Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 21 for “"Vacuum Testing"”.
-
The Design and Construction of a UHV Test System to Evaluate A Magnetron Pump-Gauge (Part B)
… and initial operation of an ultra high vacuum testing system was undertaken. The final UHV system is equipped with a residual gas analyser (RGA). </p> <p> The system was used to test a National Research Council of Canada magnetron pump-gauge. The pumping action of the device was adequate …
-
Creep, fatigue, and environmental response of Alloy 800H tested at 900 degrees C
… carried out at 900$\sp\circ$C in lab air and in vacuum on Alloy 800H. Three different notch acuities were chosen so that the effect of stress intensity on the rupture lifetimes could be examined. The effect of oxidation on the creep rupture lifetimes has also been examined using reduced section …
-
PERFORMANCE COMPARISON OF A LOW MASS VIBRATORY LUNAR SURFACE COMPACTOR IN VACUUM VERSUS ATMOSPHERE
… in collaboration with Colorado School of Mines. Testing in vacuum is necessary to simulate a relevant environment, which is required to increase the technology readiness level of this tool to TRL 5. Testing concluded significant interactions between the presence of atmosphere and other factors. …
-
Thermal Modeling and Testing of the Blue Thermal Vacuum Chamber
The Blue Thermal Vacuum Chamber (TVAC) located in the Space Environments Laboratory at California Polytechnic State University, San Luis Obispo (Cal Poly), may be used for thermal vacuum testing of test articles that fit with in the semi cylindrical test section that has a radius of approximately …
-
Design and Validation of an LED-Based Solar Simulator for Solar Cell and Thermal Testing
… solar simulators intended for photovoltaic cell testing were used primarily, supplemented by information from ASTM E491-73 for solar simulators intended for spacecraft thermal vacuum testing. Three main criteria were identified as design goals - spectral match ratio, spatial non-uniformity, and …
-
Development and Verification of an Updated Thermal Model for Cal Poly's Small Thermal Vacuum Chamber
… modifications made to the Small Thermal Vacuum (TVAC) Chamber in the Space Environments Laboratory at California Polytechnic State University, San Luis Obispo, and the development and verification of an updated thermal model reflecting these changes. The chamber was redesigned to improve …
-
Planetary Micro-Rovers with Bayesian Autonomy
… problem-solving tasks can be performed. Thermal vacuum testing of components is also done to validate their operation under space conditions.
-
Moiré interferometry at high temperatures
… measurements at high temperatures in a vacuum oven using an achromatic interferometer. The moiré system setup was designed with particular consideration for the stability, compactness, flexibility, and ease of control. A vacuum testing environment was provided to minimize the instability …
-
High-Temperature Resistojets for All-Electric Spacecraft
… first proof of concept thruster, STAR-0, through vacuum testing with Ar propellant at the University of Southampton facility. The prototypes are made of stainless steel, which limits the maximum gas temperature to approximately 1,000 K. A set of multiphysics simulations is validated against the …
-
Hobby Grade Lithium-Ion Batteries for Spacecraft Applications: Establishing an Automated Electrical Characteristics Testing Procedure For Flight Acceptance of non-Space-Grade Small Secondary Batteries
… or death. The goal of this work is to establish testing setups and procedures that will give an accurate profile of the electrochemical properties of lithium-ion batteries. Ten of the tested batteries will be used as the secondary power supply on ARKSAT-1, a CubeSat mission being conducted at the …
-
A standardized 3U CubeSat common bus architecture for improving mission success
… with deficiencies in V&V and environmental testing, with as many as 65% of CubeSat missions forgoing at least one of the following vibration testing, thermal vacuum testing, or end-to-end RF testing due to schedule and resource constraints. Collectively, these findings demonstrate that …
-
Development of Adapted Capacitance Manometer for Thermospheric Applications
An adapted capacitance manometer is a sensor composed of one fixed plate and one movable plate that is able to make accurate pressure measurements in a low pressure environment. Using detection circuitry, a change in capacitance between the two plates can be measured and correlated to a …
-
Validation and Characterization of a Laboratory Ion Source for Testing Thermal Space-Plasma Instruments
… to stimulate thermal plasma instruments in a vacuum chamber. This dissertation presents the mechanical design of the source, simulations of the potentials and charged particle trajectories in and around the source, and vacuum chamber measurements of the emitted ion beam. Once the ion source is …
-
Testing the Ariel exoplanet space observatory
… calibration and performance verification. The testing of the integrated Ariel payload will be the subject of this work. The ground calibration of the Ariel payload will take place in 2026 in the 5m vacuum chamber at the Rutherford Appleton Laboratory’s space instruments test facility. The …
-
Accident analysis of software architecture in high -reliability systems: Space Based Infrared System software problems
… years. This resulted in major failure in thermal vacuum testing. The architecture was reassessed, the new architecture so adopted was the wrong architecture. This is the accident this research has analyzed. The cause of the accident is analyzed thoroughly to understand the circumstances in which …
-
Electrical facility effects on Hall effect thrusters
… tests are performed in ground-based vacuum facilities. To ensure predictable flight operation of HETs, the ground-based testing environment must be representative of the on-orbit environment, or there must be a clear path to correlate the ground test results to expected on-orbit HET …
-
Development of the Cherenkov Camera for the EUSO-SPB2 Mission and Analysis of Above-the-Limb Observations of Cosmic-Ray Particle Showers
… electronics and integrating the camera, thermal vacuum testing, and characterizing the performance of the camera in the field. Together with the rest of the team, we deployed the payload to fly as part of a NASA pathfinder mission. We operated the payload for two days before the balloon …
-
Zkoušky tepelné vodivosti struktur pro kosmické aplikace
Tato práce se zaobírá měřením bronzového (CuSn8) a hliníkového (Al 7075) vzorku v termovakuové komoře za specificky definovaných podmínek, které se lišily vstupními výkony a teplotami regulovaných testů. Úvodní část práce řeší konstrukci termovakuové komory a potenciální výzvy, spjaté s …
-
Vývoj infrastruktury pro testování materiálů při působení vakua – outgassing
Tato diplomová práce se zabývá návrhem testovacího zařízení pro testování odplyňování (outgassing) materiálů. V teoretické části jsou popsány standarty zabývající se danou tématikou a je provedena rešerše existujících zařízení z veřejně dostupných zdrojů. Výstup teoretické části je seznam celkem …
-
Advanced analysis and testing of space equipment systems
Tepelná kontaktní vodivost (TCC) popisuje pokles teploty na rozhraní dvou těles vystavených tepelnému zatížení. Neznámá velikost TCC a její vliv se významně projevují při měření tepelné vodivosti vzorku v tepelně-vakuové komoře Leteckého ústavu VUT v Brně. Bez spolehlivých údajů o TCC není možné …
Page 1 of 2