Global ETD Search

Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.

Results

Showing 1 to 20 of 290 for “"Water Injection"”.

  1. Mechanistic modeling of low salinity water injection

    Petroleum and Geosystems Engineering

    texas Repository record for Mechanistic modeling of low salinity water injection (opens in a new tab)

  2. Expert system for oilfield water injection problems, An

    Includes bibliographical references.

    colo-mines Repository record for Expert system for oilfield water injection problems, An (opens in a new tab)

  3. Thermal signature reduction through liquid nitrogen and water injection

    … the exhaust but no infrared shielding. Second, water was injected at a flow rate of 13% of the flow of exhaust gases, producing a greater temperature reduction and some shielding. Water was then injected through a manifold at a flow rate of 118% of the flow rate of exhaust gases, producing a …

    tamu Repository record for Thermal signature reduction through liquid nitrogen and water injection (opens in a new tab)

  4. Water Injection in an Automobile Gas Turbine Combustion System

    … for this thesis. The method of solution was by water injection into the combustion gases prior to entrance into the turbine. The injection of water reduces the turbine inlet temperature, which allows the production of gas turbines from less expensive materials. This reduces the production cost …

    byu Repository record for Water Injection in an Automobile Gas Turbine Combustion System (opens in a new tab) Download PDF for Water Injection in an Automobile Gas Turbine Combustion System (opens in a new tab)

  5. Investigation of Hydraulic Fracture Water Injection in Wolfcamp Formation

    … and injecting more fluid will result in water blockage which will reduce relative permeability and also cause phase trapping where oil and gas are trapped and will not be produced. This thesis focuses on fracture half-length and the effect of water volumes injected to generate such a …

    ku Repository record for Investigation of Hydraulic Fracture Water Injection in Wolfcamp Formation (opens in a new tab)

  6. Streamline-based simulation of water injection in naturally fractured reservoirs

    The current streamline formulation is limited to single-porosity systems and is then not suitable for application to naturally fractured reservoirs. Describing the fluid transport in naturally fractured reservoirs has been recognized as a main challenge for simulation engineers due to the …

    tamu Repository record for Streamline-based simulation of water injection in naturally fractured reservoirs (opens in a new tab)

  7. Numerical modeling of cold water injection into supercritical geothermal reservoirs

    … study is to apply the improved supercritical air-water equation-of-state of the AUTOUGH2 numerical simulator to an artificial supercritical geothermal reservoir. A radially symmetric numerical model is used to investigate the response to cold water injection of a geothermal reservoir with …

    reykjavik Repository record for Numerical modeling of cold water injection into supercritical geothermal reservoirs (opens in a new tab)

  8. Modeling and Analysis of Reservoir Response to Stimulation by Water Injection

    … fracturing operations, fracturing during water-flooding of petroleum reservoirs, shale gas, and injection/extraction operations in a geothermal reservoir. During the operations, the pore pressure will increase with fluid injection into the fracture and leak off to surround the formation. …

    tamu Repository record for Modeling and Analysis of Reservoir Response to Stimulation by Water Injection (opens in a new tab)

  9. 1D SIMULATION OF DIRECT WATER INJECTION IN A SPARK IGNITED ENGINE

    … power output in spark ignited engines. Direct water injection into the combustion chamber is a potential solution to this problem by means of the ‘charge cooling’ effect of water. 1D Fluid Dynamic simulation tool GT-Power has been used to develop a test CFR S.I. engine model complete with …

    mtu Repository record for 1D SIMULATION OF DIRECT WATER INJECTION IN A SPARK IGNITED ENGINE (opens in a new tab)

  10. Water Injection and its Impact on Knock Mitigation in Spark Ignited Engines

    … mitigate knock at different operating regimes. Water due to its higher latent heat of vaporization compared to gasoline fuel has been used to reduce the charge temperature and mitigate knock. When water is injected into the intake manifold or into the cylinder, it evaporates by exchanging energy …

    mtu Repository record for Water Injection and its Impact on Knock Mitigation in Spark Ignited Engines (opens in a new tab)

  11. Recovery of Non-Aqueous Phase Liquids from Contaminated Soil by CO2-Supersaturated Water Injection

    Supersaturated water injection (SWI) is a novel remediation technology which is able to remove entrapped residual NAPLs from saturated porous media by both volatilization (partitioning of volatile contaminants into the gas phase) and mobilization (displacement of isolated NAPL residuals by gas …

    waterloo Repository record for Recovery of Non-Aqueous Phase Liquids from Contaminated Soil by CO2-Supersaturated Water Injection (opens in a new tab)

  12. THE IMPACT OF WATER INJECTION ON SPARK IGNITION ENGINE PERFORMANCE UNDER HIGH LOAD OPERATION

    … experimental effort has been completed in which water injection was investigated as a means of enabling increases in engine output and high load efficiency. Water was injected into the intake port of a direct fuel injected, 4-cylinder, boosted engine with dual independent variable valve timing. …

    mtu Repository record for THE IMPACT OF WATER INJECTION ON SPARK IGNITION ENGINE PERFORMANCE UNDER HIGH LOAD OPERATION (opens in a new tab)

  13. Computational Fluid Dynamics Modeling of the Effects of Water Injection in a Diesel Engine

    Water injection has been used in internal combustion engines for many years. It has been used to cool combustion temperatures, reduce emissions, and in some instances clean carbon buildup from the cylinder. Research has shown that the water to fuel mass ratio is most effective between 20-30%, so …

    gsu Repository record for Computational Fluid Dynamics Modeling of the Effects of Water Injection in a Diesel Engine (opens in a new tab)

Page 1 of 15