Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 12 of 12 for “"Wirebonds"”.
-
Thermal Analysis, Parasitic Extraction, and Wirebond Reliability Studies of Power Electronic Modules
… approaches is studied in detail. Reliability of wirebonds in the case of encapsulated and un-encapsulated power modules were investigated by subjecting them temperature cycling from -55ᴼC to 250ᴼC. It was found that the solder flux affected the reliability of the wirebonds. As such, it is …
-
High Temperature Packaging For Wide Bandgap Semiconductor Devices
… The new module is also without problematic wirebonds that lead to a majority of traditional module failures which also introduce parasitic inductance and increase thermal resistance. Resultantly, the module also features a severely reduced form factor in mass and volume.
-
Combined Stressors in Reliability Failure Modes in Flip-Chip Electronic Packaging
… considering the industrial tendency to replace wirebonds with solder attachment while improving the current carry capacity. This dissertation utilizes FEA simulation and an experimental approach to study the solder’s reliability. First, the SiC MOSFET packaging method using flip-chip technology …
-
Processing and Reliability Assessment of Solder Joint Interconnection for Power Chips
… of power chips is accomplished with wirebonds. Wirebonds in power devices and modules are prone to resistance, noise, parasitic oscillations, fatigue and eventual failure. Furthermore, there has been an increase demand for higher power density and better efficiency for power …
-
Design and integration of hybrid and monolithic microwave power amplifiers for wideband applications using gallium nitride technology
… matching techniques, and comparisons of both wirebonds and flip-chip bonds that are used for PA interconnections. With a focus on bandwidth enhancements and efficiency improvements, the presented hybrid PA designs achieve state of the art performance with commercially-available GaN power …
-
Advancing quantum-limited amplifiers with hybrid Josephson junctions
… eliminates the need for circuit board and wirebonds, mitigating impedance mismatch and loss at high frequencies. The WJPA delivers >20 dB gain over a 3 MHz bandwidth in the 21--23.5 GHz range, with a compression point of -125 dBm and added noise near 2 photons. These results mark the first …
-
Low Power Electronics and Thermal Management for the Cryogenic Temperature Regime
… IC. A experiment was performed to show aluminium wirebonds can act as superconducting heat switches between hot and cold devices in the same setup. Voltage noise thermometry with the cross-correlation technique was demonstrated inside the IC. This was demonstrated to work in the range 300~mK to …
-
Integrated thin film magnetics in advanced organic substrates
… integration of the released magnetic core using wirebonds; 2) the embedding of the released magnetic material using a Flip-Chip approach; 3) fully embedding the released magnetic material between the prepreg layers in the PCB stack. \newline\newline Finally, methods for the modelling and …
-
Gigahertz Modulation of a Photonic Crystal Cavity
… in the quality factor was possible. Broken wirebonds on the transducers created unintended etch channels rendering the SAW non-operational.
-
INTERFACIAL DEGRADATION OF COPPER WIRE BONDS IN THERMAL AGING AND CYCLING CONDITION
… namely, 0.5 µm, 1 µm and 4 µm, over which Cu wirebonds with four different thermosonic bond recipes are made. Results from Part II-A provide guidelines for bond comparison using bond shear analysis. Part II-B focuses on the effect of bond pad thickness on the reliability of Cu wire bonds under …
-
Die-Attachment on Copper by Nanosilver Sintering: Processing, Characterization and Reliability
… point of the assembly was the detachment of the wirebonds. Great reliability performances of nanosilver sintered die-attachment on Cu were mainly due to the low mismatch of coefficient of thermal expansion (CTE) between sintered-Ag and Cu. Meanwhile, low inter-diffusion rate between Ag and Cu …
-
Dual-band lightweight, low-cost RF front-end solutions for point-to-point wireless applications
The objective of this work is to achieve the integration of a state-of-the-art RF CMOS chip in lightweight multilayer-organic (MLO) substrates at millimeter-wave frequencies. To do this, first the substrates need to be characterized above 30 GHz. This was done through the Ring Resonator Method. …