Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 26 for “"X-cut"”.
-
Analysis and fabrication of grating assisted optical components
… waveguides fabricated by proton-exchange in X cut Y propagation LiNbO3 are experimentally investigated.
-
Design and Optimization of Temperature-Stable MEMS Resonators for Timing Applications Based on Thin-Film Lithium Tantalate
… Firstly, the thermal behavior of S0 Lamb wave X-cut Lithium Tantalate (LT) resonators is investigated, demonstrating a zero-temperature coefficient of frequency (i.e., turnover temperature) numerically. These resonators are optimized to achieve high electromechanical coupling and high turnover …
-
RESONANT CURVED PIEZOELECTRIC CANTILEVER FLUID DIODE WINGS FOR MASS-PRODUCIBLE FLYING MICROROBOTS
… 7.6 mm wings out of 7.5 micrometer thick x-cut quartz and SU-8, after developing and implementing a method to smoothly thin x-cut quartz leaving the surface free of dielectric-compromising pits using reactive ion etching (RIE). Finally, it constructs a test chamber to measure the force, …
-
Design, construction, and testing of ultrasonic transducers with modified radial velocity profiles
… electrode array on a 12. 7 mm diameter x-cut quartz disk. Each electrode is independently connected to an impedance network optimized to produce the Gaussian distribution with less than two percent maximum error. A computer aided electrode design and normalized three dimensional ultrasonic …
-
Directional Electric Field Sensing Using Slab Coupled Optical Fiber Sensors
… area of 0.5 cm x 0.5 cm achieved by using an x-cut crystal. The method is described that uses a sensitivity-matrix approach to map the measurements to field components. The calibration and testing are described resulting in an average error of 1.5º.This work also includes a description of the …
-
Gain Improvement of Er-doped Amplifiers for the Feedback Filters
… on top of an Er doped titanium diffused x-cut lithium niobate waveguide has been investigated by simultaneous analytical expressions, numerical simulations, and experimentation. Both simulation and experimental results have shown that this structure can enhance the optical gain, as …
-
Chemical and Optical Studies of the Hydrogen-Exchanged Optical Waveguides in Lithium Niobate
… been investigated by the exposure of x- and z-cut LiNbO3 waveguides to [1H] water vapour at room temperature. The z-cut [2H] hydrogen-exchanged waveguides showed reversible behaviour when exposed to [2H]-hydrogen labelled water vapour successively, unlike the x-cut waveguide which exhibited …
-
Investigating the physics of ferroelectric domains and domain walls using novel scanning probe methods
… potential across conducting domain walls in x-cut lithium niobate. Head-to-head and tail-to-tail domain walls, which exhibit n and p type conduction respectively, have been created between coplanar electrodes. The morphology of the switched domain has been established using Tomographic …
-
CHARACTERIZATION OF PROTON EXCHANGED PLANAR OPTICAL WAVEGUIDES IN ZNO:LINBO3 CRYSTALS
… proton exchanged planar optical waveguides in x-cut, y-cut, and z-cut 6mol%, ZnO-doped lithium niobate crystals (ZnO:LiNbO3) using adipic acid as proton source for the first time. The diffusion properties m1d optical features of the waveguides were optically characterised using the prism coupling …
-
Velocity of sound in solid iodine
… generating the waves were: longitudinal waves, X-cut quartz crystals of 5 and 12 Mcs.; transverse waves, Y-cut quartz crystal of. 5 Mcs. For longitudinal measurements the sample was immersed in baths of liquid helium, liquid nitrogen, solid carbon dioxide, ice, ambient room temperature, and …
-
Acousto-Optic Filter Device Using Proton-Exchanged Waveguides
… index. Multi-mode waveguides are fabricated on Y-cut LiNbO3 substrates without surface damage, though short post annealing is necessary to relieve induced strain. Planar optical waveguides are fabricated on X-cut and Z-cut LiTaO3 substrates from dilute melts without the need for prolonged post …
-
Acoustooptical techniques for ultrasonic materials evaluation: optical fiber interferometry and pulse-echo systems
… concentric ring electrodes etched on a single x-cut quartz crystal substrate with a 1 mm circular aperture at the center. By shaping the amplitude and phase profile of the high voltage pulse applied to each ring, a focused ultrasonic field results at an adjustable distance below the transducer. …
-
Design and fabrication of highly efficient electrooptic modulators using bragg grating reflectors
… of ~1542 nm for TE polarization on an x-cut, y-propagating substrate. The reflectance in the channel waveguides is found to be strongly dependent on the depth of the etched grating. The 3-dB bandwidth of 0.05 nm obtained for all tested samples is the smallest reported for waveguides in …
-
Optical Phased Arrays for High Speed, Non-Mechanical Beam Steering Applications
… The high electro-optic coefficient of the x-cut y-propagating LiNbO₃ (r₃₃ = 30.8 pm/V) is utilized by electrode structures fabricated on the LiNbO3 substrate to create low-power, low-loss beam steering with high-speed bandwidths, capable of 10 GHz and larger, as demonstrated by commercial …
-
Direct Voltage Measurements Using Bulk Acoustic Waves in LiNbO3
… ease of use, and compactness in mind. A Y+36° cut LiNbO3crystal was coupled to two acoustic transducers, where direct current (DC) voltages ranging from 128—1100\u2009V were applied transversely to the crystal. An acoustic wave was used to interrogate the crystal before, during, and after …
-
METHOD AND APPARATUS FOR THERMOACOUSTIC ANALYSIS (TAA)
… by a high voltage RF pulse excitation of an X-cut quartz transducer at its resonant frequency of 4 MHz. The waves are coupled to and from the material by two identical buffer glass rods while the material temperature is ramped accurately by a PID temperature controller. The chanqes in the …
-
Fabrication and Measurement of LT-GaAs Photoconductive Antennas and Arrays
… Further, a polarization study using an x-cut quartz rotator was conducted, validating that all four electrode shapes are highly linearly polarized. Results show that the co-polarized THz pulse is two orders of magnitude greater than the cross-polarized THz pulse. In addition, two element …
-
Studies of the analytical utility of low-temperature photoacoustic spectroscopy
… PA detectors. Two PE materials were studied, X-cut crystalline quartz and lead-zirconate-titanate (PZT). PZT was found to exhibit ~10 times higher sensitivity. PA spectra of Nd(OH)<sub>3</sub> powder at 6-8 K were taken to demonstrate the ability to acquire piezoelectrically-detected PA spectra …
-
Novel diagnostic technologies for optical communication systems
… also used to measure the chirp parameter of an X-cut LiNbO3 MZM, revealing a chirp parameter of απ/2 < 0.1 across a modulation band- width of 250-2500MHz. Additionally, the distinctive CW spectrum of a DFB laser diode was measured. Analysis of the measured CW spectrum yielded a linewidth …
-
Spectral slicing filters in titanium diffused lithium niobate (ti:linbo3)
… Both types of devices were fabricated on x-cut y-propagating LiNbO3 substrates, with N = 6 strain-induced coupling regions. The single mode channel waveguides were formed by Ti diffusion. Electrode patterns centered about the optical waveguide were defined by liftoff. In the straight channel …
Page 1 of 2