Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 146 for “"Z direction"”.
-
Effect of chemical additives on Z-direction filler distribution in paper
… brightness, and roughness are affected by the z-direction mineral filler distribution. In this study, the effect of four different parameters (filler, starch, chemical retention aids and the machine parameter (vacuum)), on the z-direction filler distribution in paper samples was investigated. …
-
Interaction of fibres and additives in mechanical pulp suspensions
… as a non-destructive technique to obtain the z-direction PCC filler distribution in paper. In TMP suspension loaded with PCC high degree of substitution (DS) tapioca starch was found to be better strength developing agent and retention aid compared to high DS potato starch. It was also found …
-
Modeling viscoelastic responses of the head/neck system during pilot ejection
… Patterson Air Force Base. Experimental head z-direction acceleration data from a first subject, L7, was reproduced accurately using the ATB model. However, Simulated head z-direction acceleration profiles for a second subject, B9, could not match experimental data for this subject, even after …
-
Reproducibility of extra-oral tongue motion in a normal cohort using a 3D motion capture system
… maximum tongue tip position in the x, y and z directions were calculated for each of the two movements at both time points and subsequently analysed. Results: The up and down range of motion (ROM) of the tongue was 48.3 ± 10.0mm (95% CI 45.7mm to 51.0mm) and for right to left ROM was 66.4 ± …
-
Smart Water Receiver for Use in the Wet Press Section of a Paper Machine
… only flows through the felt in the transversal z-direction, but also flows through the felt in the machine and cross-machine directions. On the exit side of the nip, the pressure imposed on the sheet-felt system by the rolls begins to decrease. Both the paper web and press felt begin to expand, …
-
Forces on a rotary tine aerator under normal working conditions
… the bearing mounts causing the force to change directions when the tool was working and 20 cm depth and the tine gang was set a 0º. Forward velocity was not seen to be a significant factor affecting forces on the frame. The loading in the X, Y and Z direction on the tine increased as depth …
-
Performance Improvement in Robotic Milling: Hybrid Compliance Error Compensation and Fast-Chirp Identification Approach
… TCP deflection decreases by 78 percent in the x direction and 77 percent in the y direction. Another contribution of this study is introducing a novel automated approach, termed “fast chirp”, for identifying the joints dynamic parameters, specifically stiffness and damping, in moving robots. A …
-
Numerical simulations of flow through model paper machine forming fabrics
… the two fabrics were investigated, such as the z direction separation between the paper side and machine side layers, the diameter ratio of two-row cylinders, the second row spacing between two adjacent cylinders, and variable second row spacing between two adjacent cylinders. The simulations …
-
Incorporating rapid prototyping technology into the IE and MAE undergraduate curriculum at WVU
… in lower expansion of the part in X and Z direction, however the expansion in Y direction was higher under the same conditions. At 46.24% saturation level and higher curing time of 2.5 hrs expansion in the Z direction was found to be higher compared to that of X and Y direction. Experiments …
-
Analyse der Chromosomenverteilung in menschlichen Fibroblasten mittels 3D-Vielfarben Fluoreszenz in situ Hybridisierung
… large in xy-diameter (10-20µm), but flat in z-direction (5µm). In these nuclei chromosome territories typically lie side by side or slightly above each other. The question whether these arrangements are ordered or variable has yielded conflicting answers. We hybridised an improved …
-
The Whitehead Link on the Cubic Lattice
… vertex one unit away in the x-, y-, or z-direction. This thesis will show that the Whitehead Link needs at least 34 steps to be embedded on the cubic lattice.
-
Improving Alignment of Kinematically Coupled Polymer Microfluidic Modules by Modularization of Coupling Features
… method is 22 percent. Maximum reduction in z-direction misalignment when decreasing only post dimension tolerances is 51 percent. However, simulations showed significant benefit to also decreasing groove dimension tolerances. When both are considered and set to ±2 µm, the maximum z-direction …
-
Do post-surgical unilateral cleft lip and palate patients have a comparable dynamic facial expression to a non-cleft population?
… and left corners of the mouth, in the x, y, z direction and Euclidian distance were statistically significantly (p<0.05) less in the cleft group (20-40% less) compared to the control group during maximum smile. This was greater than 3mm, therefore clinically significant. There was a baseline …
-
Image Restoration through Deconvolution of Computer Tomography Images Generated from Helical Projection Data
… collected while the patient is moving in the z direction and, thus, does not have all the data collected from the same plane. As a result there is less resolution in the images. This thesis describes an image restoration technique that improves resolution in images generated from CT data …
-
Spectroscopic studies of substrates used for solid-phase synthesis and combinatorial chemistry : fundamentals and applications
… a function of distance down through the bead (z-direction) is seen to be symmetric about the bead centre for the swollen beads but a distinct asymmetry is observed for dry beads.. This is due to the re & action of light at the air/bead interface leading to the bead acting as a lens. A discrepancy …
-
A Comparison of Force and Pressure Coefficients on Dome, Cube and Prism Shaped Buildings due to Straight and Tornadic Wind Using Three Dimensional Computational Fluids Dynamics
… those on the dome by at least 90% in the x-y directions, and 140% in the z direction. The tornado pressure coefficients on cube and prisms were greater at least 200%. The force coefficients on cube and prisms due to SL wind were higher than those on the dome due to tornado wind by about 100% …
-
CRYOGENIC ATOMIC FORCE MICROSCOPE FOR CHARACTERIZATION OF NANOSTRUCTURES
… design provides reliable autoapporach in the Z direction. AFM imaging with 10nm horizontal and ~2 angstrom vertical resolution has been achieved. We have used this AFM in the current-voltage characterization of diodes, and, with a modified sensing mechanism, electrical force microscopy (EFM) and …
Page 1 of 8