Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 21 for “"active clamp"”.
-
Active-clamp PWM converters: design-oriented analysis and small-signal characterization
… thesis addresses issues related to the use of an active clamp (ACL) circuit in high-frequency PWM converters with an electrical isolation. Existing design guidelines and design trade-offs for the ACL in forward and flyback converters are reviewed, and specific properties of both circuits that are …
-
Design of Active Clamp for Fast Transient Voltage Regulator-Down (VRD) Applications
… control and current control buck converter, active clamp has a lot of the advantages for the transient response. With proper design, active clamp can generate a very high bandwidth since there is no compensator needed in the control loop. Since active clamp bypasses inductor and is connected …
-
The Design of an Asic Control Chip for a Forward Active Clamp Converter and the Investigation of Integratable Lateral Power Devices
… the design of an ASIC control chip for a forward active clamp converter is presented. Integration of the control and drive circuit into one IC chip results in higher power density, higher reliability for the converter module. The designed ASIC control chip uses a 2.0 um N well Analog CMOS process, …
-
Energy Harvesting from Exercise Machines: Forward Converters with a Central Inverter
This thesis presents an active clamp forward converter for use in the Energy Harvesting From Exercise Machines project. Ideally, this converter will find use as the centerpiece in a process that links elliptical trainers to the California grid. This active clamp forward converter boasts a 14V-60V …
-
Investigation of High-Input-Voltage Non-Isolated Voltage Regulator Modules Topology Candidates
… the tapped-inductor buck converter and the active-clamp couple-buck converter. The limitations of today¡¯s synchronous buck approach are identified. The extreme duty cycle of the current topology makes it difficult to design an efficient VRM with decent transient response. The …
-
Isolated Bi-directional DC-DC Converter with Smooth Start-up Transition
… in the house such as home appliances. The dual active bridge (DAB) converter is very useful because of its high power capability and efficiency. Its symmetry is effective in transferring power in both directions. However, the DAB converter has drawbacks in the start-up stage. These drawbacks in …
-
Developing Modeling and Simulation Methodology for Virtual Prototype Power Supply System
… the anomalies of the forward converter with active-clamp reset circuit extensively and facilitate the design and improve the circuit performances by utilizing the virtual prototype. With the help of the virtual prototype, it is the first time that the designer is able to analyze the dynamic …
-
Low-power PFC and forward converters : methods to improve performance
… factor correction. This is because only one active switching stage is used in the converters. Small signal and steady state analysis are performed for the dither converter. A resonant type snubber is analyzed for the BIFRED and BIBRED converters and a new type of clamp circuit is developed …
-
Analysis of an Isolated Bidirectional Ćuk Converter
… of Arkansas. The idea of integrating an active-clamp snubber circuit on each side of the converter, proposed by Dr. Sudip Mazumder from the University of Illinois, Chicago, limits the additional voltage stresses on the components due to the energy from the transformer’s leakage …
-
Multiport DC-DC conversion incorporating integrated magnetics for renewables
… converter with integrated magnetics. This has an active-clamp ZVS turn-on circuit with the addition of a ZCS turn-off. The design of the external components and simulation results for the same are presented as well.
-
New Topologies for High Voltage Gain DC-DC Power Electronic Converters – Theoretical Analysis and Experimental Validation
… an impedance-source-based converter using an active clamp is proposed. Unlike the conventional CI-based converters, in which higher voltage gain is achieved by using a higher turns ratio for the windings of the CI, this impedance-source-based converter can achieve substantial voltage gain with …
-
A novel reconfigurable multiport converter for increased utilization of power electronic interface in grid integrated PV/EV/battery systems
… synchronous buck converter, current-fed dual-active-bridge, voltage-fed dual-active-bridge (DAB), dual-input current-fed DAB with an active clamp and current/voltage-fed DAB reconfiguration. This reconfigurability enables multi purpose utilization of components, possibility of alternative …
-
Application of Integrated Magnetics and Discontinuous Conduction Mode to Multi-port DC-DC Power Conversion for integrating PV panels with storage
… converter with integrated magnetics. This has an active-clamp Zero-Voltage Switching (ZVS) turn-on circuit with the addition of a Zero-Current Switching (ZCS) turn-o. The design of the external components and simulation results for the same are presented as well. Finally, with the ever-increasing …
-
Zero-voltage switched resonant and PWM converters: design-oriented analysis and performance evaluation
… which are directly proportional to the reactive energy required by the resonant tank. The comparison of the different converters is based on the reactive energy required for ZVS. The study considers resonant converters with conventional variable frequency control and with phase-shift …
-
Analysis and Design of Soft-Switching Current-fed Bi-directional Power Conversion for Multifunctional Plug-in EV Charging
… enable zero current commutated (ZCC) without any active clamp circuit or passive snubbers, which significantly reduced switching losses, footprints, and cost. The converters steady-state operation and design equations are reported in detail. The simulation results from PSIM 11.04 software and the …
-
Topology and Control Investigation for Low-voltage High-current Isolated DC-DC Converters
… topology is proposed. Basically, by adding an active branch to the conventional half-bridge topology, the leakage inductance energy is trapped during the freewheeling time, and the energy is released to achieve ZVS for the other switch. In addition, a modified ZVS half-bridge topology is …
-
High Current Density Low Voltage Isolated Dc-dc Converterswith Fast Transient Response
… of optocoupler to increase the system bandwidth. Active-clamp half bridge dc-dc converter with secondary-side control is presented and one industry standard 16th prototype is built and tested; good efficiency and transient response are shown in the experimental section. However, one key issue for …
-
Integration Challenges In High Power Density Wide Bandgap Based Circuits for Transportation Applications
… a dual-output, PCB-embedded transformer based active-clamp Flyback (ACF) gate-drive power supply (GDPS) for automotive applications is proposed. It has been demonstrated that the PCB-embedding technique effectively improves converter power density. The final prototype achieves a power density …
-
Investigation of Power Semiconductor Devices for High Frequency High Density Power Converters
… operation. It is usually required that the active power devices operate at higher switching frequencies to shrink the passive components volume. The power semiconductor devices for high frequency high density power converter applications have been investigated. Firstly, the methodology is …
-
Design and Analysis of High Voltage to 48V DC-DC Converter Topologies for Automotive Applications
… optimized to evaluate its efficiency to the Dual Active Bridge(DAB) with its chosen modulation approaches based on various modulation comparisons. From all analyses, the Phase Shifted Full Bridge(PSFB) observes extremely high turn-off voltage oscillations across the MOSFETs on the secondary side, …
Page 1 of 2