Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 41 for “"capacitive load"”.
-
A highly efficient amplifier for driving a capacitive load
… sine waves between 25 and 100 kHz for a 5 nF load was designed, built and tested. The amplifier requires the system controller to configure a set of inductors within the amplifier for the frequency prior to receiving the signal. These inductors resonate with the load capacitance; thereby …
-
An efficient switching amplifier for driving a capacitive load
… voltage, phase linear amplifier for driving a capacitive load is described. With a load of 35 nanofarads, output signals approaching 200 volts peak-to-peak axe obtained with power dissipation on the order of 25 watts for a 33 KHz, 80 volt amplitude output sine wave. The amplifier has a phase …
-
A Four-stage Power and Area Efficient OTA with 30 × (400pf – 12nf) Capacitive Load Drive Range
… system requirements, in addition to ultra-large capacitive load drivability (nF-range load capacitor), are useful in applications including LCD drivers, low dropout (LDO) linear regulators, headphone drivers, etc. The major drawback of multistage OTAs is the stability concerns since each added …
-
Design and characterization of a smart bit for in-situ force measurement, using capacitive load cells and acoustic spectra analysis to determine rock type and tool wear in rock excavation process
… Three different sensor designs were tested: a capacitive load cell with non-linear dynamics used to classify material type and tool wear conditions, an acoustic sensor used to classify tool wear, and a capacitive load cell with linear dynamics used to measure the cutting forces. Full scale rock …
-
Design and Development of High-Frequency Switching Amplifiers Used for Smart Material Actuators With Current Mode Control
… a smart material actuator is ordinarily a highly capacitive load. Its capacitance is non-linear and its strain is hysteretic with respect to its electrical control signal. This actuator's reactive load property usually causes a large portion of reactive power circulating between the power …
-
DESIGN OF ANALOG VLSI CIRCUIT : A DIFFERENTIAL-IN DIFFERENTIAL-OUT HIGH SPEED, HIGH GAIN OP AMP
… a unity-gain frequency of 180 Mhz when driving a capacitive load of 5 pF. The undesired common mode gain in the DIDO op amp is very high. Hence commonmode feedback was used to reduce the output common-mode voltage. HSPICE was used for circuit simulations in this project. The transistor model used …
-
Clock tree synthesis for prescribed skew specifications
… skew targets, sink location proximities and capacitive load balance are analyzed. Based on this analysis, a maximum delay-target ordering merging scheme is suggested to minimize wire and buffer area, which results in lesser cost, power consumption and vulnerability to process variations. …
-
Exploiting level sensitive latches in wire pipelining
… or sinks, and the location in rectangular plane, capacitive load and required arrival time at each of the destinations. The user also defines a library of non-clocked (buffer) elements and clocked elements (flip-flop and latch), also known as synchronous elements. The first procedure performs …
-
Optimizing the Energy Transfer of Pulse Transformers
… and tested for the purpose of quickly charging a capacitive load to a differential voltage of up to 100 kV. The first pulse charger was designed and tested to charge a 0.5 nF load to +/- 50 kV in less than 10 μs. This pulse charger was also designed to be modular, so multiple loads could be …
-
Low power high resolution electronic driver for deformable mirror systems
… of multi-stage amplifier capable to drive large load capacitor, and HV analog switch robust to analog signal noise during OFF state. The specific research contributions of this work include (1) A feed-forward stage in combination with a class B output stage is proposed in the HV multi-stage power …
-
High performance building blocks for wireless receiver: multi-stage amplifiers and low noise amplifiers
… silicon area for the application where a large capacitive load exists. They were designed using AMI 0.5 m µ CMOS technology. The simulation and measurement results show they have the best Figure-of-Merits (FOMs) in terms of small signal and large signal performances, with 4.6MHz and 9MHz …
-
High bandwidth low power operational amplifier design and compensation techniques
… <p>product (GBW) driving a large capacitive load (100 pF). The GBW of the Op Amp was improved by a factor of 10 times compared to the miller compensation scheme. The amplifier documented in this thesis achieved a higher simulated figures-of-merit (FoMs) compared to the state-of-art …
-
Energy harvesting from ship vibration
… converter (linear generator) with a resistive load was developed and the relations of system parameters to power output were deduced. Based on these relations, the design principles of the harvested are summarized into two steps: i) tune the natural frequency of the linear generator to match …
-
Design Technique for Analog Temperature Compensation of Crystal Oscillators
… oscillator as a function of the crystal's capacitive load. This relationship leads to the development of the theory of temperature compensation by a crystal's external load capacitance. An example of the TCXO design process is demonstrated with the aid of a MATLAB script.
-
Lumped silicon photonic Mach-Zehnder modulators for high-speed optical interconnects
… MZMs, specifically, as their unterminated, capacitive load holds promise for lower power consumption than more typical travelling-wave MZMs with resistive terminations. Detailed characterisations and simulations of dual-drive silicon photonic lumped MZMs are made to investigate the key …
-
Modeling and Control Design of a Bidirectional PWM Converter for Single-phase Energy Systems
… is of importance because of the sensitive loads. In this thesis, different multi-loop-based control schemes are investigated and compared, especially between the load current feedback control, PR control and capacitor current loop control. It shows that PR controller reduces the …
-
ANALYTIC METHODS FOR TIMING ANALYSIS OF INTERCONNECTS IN CMOS VERY LARGE SCALE INTEGRATED CIRCUITS
… However these were done by either assuming the load to be purely capacitive or with no particular regard to accuracy of driver resistance. With the current advances in IC fabrication process, the minimum feature size of interconnect has greatly reduced. Also, the length of intercon next is …
-
Low Power TFT Logic Implementation on Display Backplane, Using Unipolar TFTs
… a gate of thousands of pixels, there is a high capacitive load, which contributes to a high dynamic power consumption. Recent research has been investigating the use of TFTs to change the off-panel integrated-circuit (IC) and integrate it onto the display backplane, eliminating the need for …
-
Baseband analog circuits in deep-submicron cmos technologies targeted for mobile multimedia
… over conventional Gm-C equalizers. Secondly, a load capacitance aware compensation for 3-stage amplifiers is presented. A class-AB 16W headphone driver designed using this scheme in 130nm technology is experimentally shown to handle 1pF to 22nF capacitive load while consuming as low as 1.2mW of …
-
Neurostimulator with Waveforms Inspired by Nature for Wearable Electro-Acupuncture
… discussed. The circuit is also analyzed with a capacitive load using a simplified Randles model to represent the electrode-electrolyte interface, and the output is measured in phosphate-buffered saline (PBS) solution as the load with acupuncture needles as electrodes. The circuit is designed to …
Page 1 of 3