Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 16 of 16 for “"class E amplifier"”.
-
Photoswitch-based Class E microwave power amplifer
… needed. The primary source of loss is the final amplifier in the transmission-receive (TR) module. The purpose of this project was to investigate the use of a novel Class E amplifier operating at 10 GHz. The Class E amplifier was studied because of its simplicity and excellent high frequency …
-
MSM photodiode as the switching element in a photoswitch-based class E microwave power amplifier
… for use as the switching element in a 2 GHz class E amplifier. The application of this amplifier is as the final-stage amplifier in the transmit-receive module of a phased-array radar system. The goal of the photonic design, the use of a photoswitch in place of the typical transistor, is …
-
Development of a High-Efficiency, Low-Power RF Power Amplifier for Use in a High-Temperature Environment
… design of a high efficiency, low power, RF power amplifier that can operate over an extended temperature range. The amplifier has been implemented as a hybrid circuit with the active device fabricated in a 0.5μm silicon-on- sapphire CMOS technology and passive components implemented off-chip. …
-
PIN photodiode controlled class E microwave power amplifier
… is to design, build and test a switched-mode class E amplifier operating at 1GHz, using a PIN photodiode as switch. In order to explore the optically controlled class E amplifier configuration, I have done some research on characteristics of PN junction photodiode, PIN photodiode and avalanche …
-
ΝΕΕΣ ΜΕΘΟΔΟΙ ΚΑΙ ΑΠΟΤΕΛΕΣΜΑΤΑ ΣΤΗΝ ΑΝΑΛΥΣΗ ΚΑΙ ΣΧΕΔΙΑΣΜΟ ΣΥΝΤΟΝΙΣΜΕΝΩΝ ΕΝΙΣΧΥΤΩΝ ΙΣΧΥΟΣ ΤΑΞΗΣ Ε
THE ANALYSIS OF A MORE GENERAL CLASS E AMPLIFIER CONFIGURATION IS DESCRIBED WHICH CAN YIELD RESULTS FOR MOST OF THE OTHER CLASS E AMLIFIER CONFIGURATIONS PUBLISHED THUS FAR, BY MEANS OF SIMPLY IMPOSING THE PROPER DESIGN CONDITIONS. FURTHERMORE, THIS ANALYSIS TAKES INTO ACCOUNT MOST OF THE IMPORTANT …
-
Design of Class-E Radio Frequency Power Amplifier
Power amplifiers (PA) are typically the most power-consuming building blocks of RF transceivers. Therefore, the design of a high-efficiency radio frequency power amplifier is the most obvious solution to overcoming the battery lifetime limitation in the portable communication systems. A power …
-
A Class-E Inductive Powering Link with Backward Data Communications for Implantable Sensor Systems
… unit incorporates a high-efficiency switch-mode Class-E amplifier operating at ~200 kHz for driving the primary coil. The secondary unit consists of a parallel resonant coil followed by the power recovery circuitry. Means for backward data communication from the internal to the external unit over …
-
A Resonant Synchronous Gate Driver for GaN e-HEMTs
… synchronous gate driver applied to a push-pull Class E amplifier for wireless power transfer.
-
The design and implementation of an electronic article surveillance system in the high frequency band
… of the inductive transmitter coil. Therefore, a class E amplifier was designed to incorporate the transmitter coil in the amplifier’s load network which allows for soft switching and reduces voltage spiking. Finally, two detection methods for RF tags were investigated. The first method is based …
-
Design of efficient wireless power-transfer system and piezoelectric transducer for sonoporation-based drug delivery implants
… % of present design. By using an efficient power amplifier (class-E amplifier, efficiency 80%), an overall system efficiency of 22% can be achieved.
-
Investigation into the use of high-efficiency switched-mode class E power amplifiers for high-dynamic range pulse-mode applications
… of time. These systems commonly use a power amplifier in the transmitter to raise the power level of the transmitted signal to a value sufficient to meet system sensitivity requirements. In high-dynamic range systems, the power amplifier pulse must turn off at a rate compatible with the …
-
Development of Cubesat Thrusters
… with the Stanford Power Lab. It is based on the Class-E amplifier topology, which operates the power semiconductor at the two extremes - fully conducting to fully cut off, spending little time in the linear, lossy region of the transfer curve. This RF source, matched with a suitable DC power …
-
AM vysílač pro experimentální účely
Bakalářská práce se zabývá problematikou, návrhem a realizací analogového AM vysílače pro experimentální účely. V práci jsou rozebrány jednotlivé bloky obvodu, je navržena bloková a obvodová struktura vysílače s moderními součástkami, která je po simulacích následně realizována. Implementace …
-
Energy-efficient and miniaturized radio frequency systems for biomedical implants
Neural interfaces promise tremendous progress in the field of biomedical technology: They can be applied to investigate and even suppress neural diseases, allow to bridge damaged peripheral nerves to reestablish motion and enable robotic assistance devices to be controlled by pure imagination. …
-
Acoustic Power Transfer Leveraging Piezoelectricity and Metamaterials
Acoustic power transfer, or ultrasonic power transfer (UPT) more specifically, has received growing attention as a viable approach for wireless power delivery to low-power electronic devices. It has found applications in powering biomedical implants, sensors in sealed metallic enclosures, and …