Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 91 for “"cone angle"”.
-
Projection print resolution as a function of illumination cone angle
… One of these of potential importance is the cone angle of the illumination furnished by the printer at a given point on the negative. Projection printers fall into two classes: those employing diffuse illumination, in which the illumination cone angle may approach 180 degrees, and those …
-
Analysis of the effects of cone angle on a cavity backed log periodic array antenna
Master of Science (M.S.)
-
Analysis of Flow in a 3D Chamber and a 2D Spray Nozzle to Approximate the Exiting Jet Free Surface
… behaviors exiting the 2D spray nozzle. The cone angle and free surface height located at the end of the free surface are two significant factors to determine the spraying area on a heated plane. This process is a reasonable representation of many industrial cooling application. The whole …
-
Analysis of Flow in a Spray Nozzle With Emphasis on Exiting Jet Free Surface
… an increase in the free surface height and cone angle. For the various radial locations of the outer inlet slot, it was noted that a position at approximately 75% of the nozzle radius produced the largest free surface height. The largest cone angle was produced when the outer inlet slot was …
-
Computational Fluid Dynamics Modeling of Projectile Drag in Baffled-Tube Ram Accelerator
… using computational fluid dynamics (CFD). Nose cone angle, tail cone angle, shoulder diameter, and shoulder length were varied to investigate their influence on drag. The geometric parameters considered here were based on previous experiments conducted in a BTRA. The velocity of the projectile …
-
Insights into the solar wind conditions near Mars from data science techniques
… to be notably steadier in field strength, clock angle and cone angle direction during the Mars Global Surveyor (MGS) mission than the Mars Atmosphere and Volatile Evolution (MAVEN) mission. Additionally, the variability of the field strength, clock angle and cone angle were all found to be …
-
In-situ control of magnetic multilayers studied with polarised neutron reflectometry
… the ability to study the depth profile of the cone angle and damping. This measurement was performed in two geometries, one where the sample magnetisation and neutron polarisation are aligned and the other where there is an angle between the magnetisation and neutron polarisation. The second of …
-
Computational Modeling of Nitrogen Oxide Emissions From Biodiesel Combustion Based on Accurate Fuel Properties
… The results indicated that increasing spray cone angle, retarding start of injection, applying exhaust gas recirculation (EGR) and charge air cooling were all effective in reducing NOx emissions from biodiesel.
-
Cellular Sorting of the Dictyostelium discoideum Slug
… the effects of a cell's active force and cone angle revealed that a cone angle less than 10 degrees or greater than 30 degrees and an active force less than 2N or greater than 6N of the prestalk cells led to unsatisfactory conditions, resulting in insufficiently directed cell movement, and …
-
VIBRATION ANALYSIS OF ROTATING TRUNCATED CIRCULAR CONICAL SHELLS
… (GDQ) method. The influences of rotating speed, cone angle, geometric properties, material properties, meridional wave number, circumferential wave number, boundary conditions and initial stress on the frequency characteristics are also discussed in detail. For the rotating conical shell, results …
-
Numerical Simulation Of Conventional Fuels And Biofuels Dispersion And Vaporization Process In Co-flow And Cross-flow Premixers
… showed that a low speed injection and high cone angle improved performance. All fuels achieved complete vaporization under a iv spray cone angle of 140°. In general, it was found that cross-flow injection achieved better vaporization performance than co-flow injection. A correlation is …
-
Spin-forging of sheet metal cones
… component forces during the spin-forging of cones from two sheet metals. Some of the theoretical methods available for the analysis of metal-forging problems have been used to determine the various forming forces involved in the process. The spin-forging operation was performed on a robust …
-
Characterisation and development of the incremental shear forming process for nickel-based aerospace structures
… process applied to 304L stainless steel and Inconel 718 and intended to facilitate an improved exploitation route of the technology into component applications by characterising it geometrically and metallurgically. First, the identification and impact of the key processing variables (KPVs) on …
-
Spray and Combustion Studies of High Reactivity Gasoline in Comparison to Diesel under Advanced Compression Ignition Engine Conditions
… emissions benefit of gasoline. A transient spray cone angle correlation was developed based on the experimental measurements. The correlation was developed to improve the description of fuel-air mixing in computational fluid dynamic (CFD) simulations. The correlation was integrated with CFD …
-
Cone Beam Tomographic Image Reconstruction: Algorithm Development and Application in Small Animal Imaging
… toward more detector rows, leading naturally to cone beam geometry. Therefore, algorithms accounting properly for the cone beam geometry have to be developed. There are two types of helical cone beam algorithms: one approximate, the other exact. Approximate methods are basically extensions of two …
-
A confocal scanning laser holography (CSLH) microscope to non-intrusively measure the three-dimensional temperature and composition of a fluid
… of practical applications. This limits the scan angle to the cone angle of the probe beam only. Reconstruction of the 3D temperature given restricted scanning from a single viewing window places a burden on the reconstruction algorithm to produce low reconstruction error. Three-dimensional …
-
The analysis of offshore foundations subjected to combined loading
… foundations such as footing embedment and cone angle were taken into consideration. Based on the numerical results, a set of empirical expressions for elastic stiffness coefficient was derived. For footing stability calculations, large horizontal or moment loads can cause the footing to …
-
Development and Testing of a CFD-Based Optimization System for Axially Symmetric Rocket Nozzles
… System(STS)-class nozzles. The optimum cone angle (Ocone) for the conical micronozzle was 26.016°, producing a specific impulse Isp) of 597.279-s using molecular hydrogen. This value agrees with those obtained by various researchers using computational fluid dynamics analyses. The …
-
A study on the characteristics of the flow inside a thermostatic expansion valve
… A new image processing method is proposed for cone angle and film thickness determination. A Phase Doppler Anemometry (PDA) system was used later to measure the size and velocity of individual droplets passing the location at the outlet of the orifice. It is found that the increase of the …
-
An investigation of the V-I characteristics of electrical discharges in Argon and their dependence on gap length and pressure
… variations in electrode material, point cone angle and tip radii. Relations were developed governing characteristics such as threshold and breakdown voltages, critical field strength and general shape of the voltage vs. current (V-I) curve, of each of the Townsend, coronal and arc phases …
Page 1 of 5