Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 18 of 18 for “"cutter head"”.
-
Measuring the effects of cutter suction dredge operating parameters on minor losses due to fixed screens installed at the suction inlet
… and versatile types of modern dredges is the cutter suction dredge. Specific regulations mandate the placement of screens over the suction mouth during dredging operations to prevent ordnance, wildlife, and other debris from entering the system; however, these screens change the operational …
-
Measuring the Effects of Cutter Suction Dredge Operating Parameters on Minor Losses due to Fixed Screens Installed at the Suction Inlet
… and versatile types of modern dredges is the cutter suction dredge. Specific regulations mandate the placement of screens over the suction mouth during dredging operations to prevent ordnance, wildlife, and other debris from entering the system; however, these screens change the operational …
-
Comparison of Experimental and Theoretical Forces on a Model Dredge Cutterhead
… the forces expected on an average dredge. For a cutter suction dredge one of the largest forces is applied on the cutter head. To determine the design criteria for a given cutter suction dredge the forces on the cutter head must be known. Forces on a 33 cm (13 inch) model cutter head have been …
-
Near-Field Sediment Resuspension Measurement and Modeling for Cutter Suction Dredging Operations
… an estimation of turbidity created during a cutter suction dredging operation. This estimation was facilited by the development of resuspension measurement and data acquisition techniques in a laboratory setting. Near-field turbidity measurements around the cutter head were measured in the …
-
Επιτελεστικότητα μηχανών ολομέτωπης διάνοιξης αβαθών σηράγγων
… face support and the choice of the machine cutter head to provide it during boring, in order to restrict surface settlements within tolerable limits.The scope of this research is to make a new approach to control Mechanized Tunnelling Works with Earth Pressure Balance machines, by including …
-
Defining a Model for Tool Consumption Rate on Asphalt Reclamation Machines
… placement and pattern of cutting picks on the cutter head. Previous studies, focused on mining and excavation applications, have shown strong correlation between placement and wear. The following study employs a screening experiment (observational study) to find significant contributors to tool …
-
Numerical simulation of continuous miner rock cutting process
… rotation and advance of a continuous miner cutter head is simulated by the Finite Element Method with explicit time integration, while dynamic contact with an element erosion algorithm is utilized to model the impact between the bits and the rock elements. Two rock failure modes, shear …
-
An investigation on the influence of microwave energy on basic mechanical properties of hard rocks
… with tunnel boring machines (TBMs) or road headers is becoming more popular and commonly used by contractors. One of the main disadvantages of such system is that, it cannot handle very hard rocks and uneconomical major disc or bit wear takes place. Today, novel explosive free rock breaking …
-
Experimental study of pressure drop and bubble size in a laboratory scale compressed air foam generation system
… agent, is injected into the soil at the cutter head of the tunnel boring machine. The foam transforms the excavated material into a deformable soil paste that provides a homogenous pressure to the surrounding ground, improves stability of the tunnel face, and minimizes friction and wear …
-
High gain circular polarized antenna design for harsh mining environments
… the information from the tools mounted on the cutterhead to the machine. Due to the spinning motion of the machine’s drums or bits, a circular polarized (CP) antenna design is necessary to ensure maximum data transfer from various orientations. The working environment of the antenna is often …
-
Rock-mass classification in tunneling based on seismic velocities and tunnel- driving data using support vector machines
… of seismic systems as a predictive tool ahead of tunneling. These seismic systems are either specialized for hard rock or soft rock excavations. In this study, the hypothesis is tested, if artificial intelligence approaches are capable to deduce automatically and in real time critical rock …
-
Advanced methods for rock discontinuities estimation in tunneling
… the prediction of lithological discontinuities ahead of a tunnel face, in a tunnel under construction, i.e. the identification of whatever type of zone producing a reflection of the seismic waves generated in a source point. Typical excitations are the blasting, the hammer or magneto-strictive …
-
COMPARING MECHANICAL MASTICATION, HERBICIDE APPLICATION, AND PRESCRIBED FIRE WITHIN AN ESTABLISHED LONGLEAF PINE (PINUS PALUSTRIS MILL.) ECOSYSTEM
… consisted of a mix of backing, flanking, and head fires. The herbicide used was the granular form of hexazinone [3-cyclohexyl=6-(dimethylamino)-1-methy-1,5-triazine-2,4(1H,3H)-dione] also known as DupontTM Velpar ULW®, which was broadcast evenly at a rate of 1.26 kg a.i./ha. A Bobcat T-300 …
-
Konstrukce natáčivé frézovací hlavy
Cílem této práce je studie variant natáčivých frézovacích hlav pro CNC stroje.Zpráva popisuje konkrétní konstrukční řešení natáčivé frézovací hlavy pro frézovací stroj, součástí je také technická zpráva a ekonomické zhodnocení.
-
Prognose von Aktivierungsparametern für die maschinelle Gewinnung hochfester Gesteine
Die maschinelle Gewinnung ist in der Lage, den verantwortungsvollen Umgang mit Lagerstätten und die Sicherheit in Bergwerken zu erhöhen. Dennoch hat sie sich bisher nicht in gekurvten Strecken und in untertägigen Abbauen des Festgesteinsbergbaus etablieren können. Es wird daher überprüft, welche …
-
Konstrukce tloušťkovací frézky
Bakalárska práca sa zaoberá návrhom hrúbkovacej (česky tloušťkovacej) frézky na opracovanie dreva. V úvodnej časti je vypracovaný prehľad problematiky spracovania dreva, existujúcich konštrukčných riešení a systémový rozbor stroja. Na základe stanovených požiadaviek sú navrhnuté tri konštrukčné …
-
Řešení technologie součásti "Nátrubek" ve firmě ČKD Hradec Králové.
Zpracování kompletní výrobní dokumentace pro zadanou součást „Nátrubek“ pro univerzální a CNC stroje. Výroba součásti je navržena základními obráběcími metodami (tj. soustružení, frézování a vrtání). Zhodnocení je provedeno na podmínky zavedení do výroby vyhovující pro firmu ČKD Hradec Králové.
-
Obrábění součásti "Stator elektromotoru" ve firmě PBS Velká Bíteš.
Ve své práci jsem představil nový způsob výroby součástí ,,stator elektromotoru“ ve firmě První brněnská strojírna Velká Bíteš a.s, kterým je možné nahradit stávající technologii. Při sestavování této práce jsem použil technologické zvyklosti využívané ve výše uvedené firmě.