Global ETD Search

Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.

Results

Showing 1 to 20 of 293 for “"cutting tools"”.

  1. Cryogenic treatment of cutting tools

    … of cryogenically treated tungsten carbide cutting tools and the mechanism responsible for their improved wear resistance. Experiments show that the treated tools show better wear resistance during the initial part of cutting, but deteriorates as time progresses. Other experiments involving …

    nus Repository record for Cryogenic treatment of cutting tools (opens in a new tab) Download file for Cryogenic treatment of cutting tools (opens in a new tab)

  2. Stress analysis of metal cutting tools

    Metal cutting tools experience cutting forces distributed over a small chip-tool contact area. When the magnitude of the stresses induced by the cutting forces exceeds the tool material fatigue strength, failure of the cutting tool results. In this thesis, stress analysis in cutting tools is …

    ubc Repository record for Stress analysis of metal cutting tools (opens in a new tab) Download PDF for Stress analysis of metal cutting tools (opens in a new tab)

  3. Electrical Discharge Texturing of Cutting Tools

    … at the interface between the rake face of the cutting tool and the chip. Tool rake face friction adversely influences the chip formation process and consumes about 25% of the total cutting energy. Friction in cutting can be controlled and reduced by introducing a lubricant into the tool-chip …

    mcmaster Repository record for Electrical Discharge Texturing of Cutting Tools (opens in a new tab)

  4. Sustainable machining using micro-textured cutting tools

    … is the implementation of micro-textured cutting tools. Micro-textures decrease the chip-tool contact length and thus reduce friction and heat which lead to better surface quality and longer tool life. However, micro-cutting of the bottom side of the chip, known as derivative cutting, is …

    uoit Repository record for Sustainable machining using micro-textured cutting tools (opens in a new tab)

  5. The Nitriding Of High Speed Steel Cutting Tools

    … downtime. Saltbath nitriding of high speed steel tools adds only about 1%to the cost of a finished tool, but has been found to confer benefits considerably in excess of this over a range of cutting conditions .A series of cutting tests is described, during which cutting forces and tool …

    plymouth Repository record for The Nitriding Of High Speed Steel Cutting Tools (opens in a new tab)

  6. Chip breaking performance of cutting tools with unusual forms.

    … chip breaking are reexamined by conducting cutting tests on laboratory prepared tools. These experiments enable the repeatability of data to be assessed. The range of workpiece materials is also extended. A nomogram is devised, using the results of these tests, to predict the range of …

    sheffield-hallam Download PDF for Chip breaking performance of cutting tools with unusual forms. (opens in a new tab)

  7. High Temperature Deformation Behavior of Cemented Carbide Cutting Tools

    Made available in DSpace on 2014-12-12T00:32:37Z (GMT). No. of bitstreams: 1 7514078.pdf: 4565521 bytes, checksum: b396e97761098d04753d979246661b6b (MD5) Previous issue date: 1975

    uiuc Repository record for High Temperature Deformation Behavior of Cemented Carbide Cutting Tools (opens in a new tab)

  8. Mathematical modelling and in-process monitoring techniques for cutting tools.

    … for mathematical models which describe the cutting tool-workpiece interaction and for accurate on-line monitoring of tool-state. These are essential requirements for the achievement of unmanned and computerized machining processes. Techniques are used to design the experiments which …

    whiterose Download PDF for Mathematical modelling and in-process monitoring techniques for cutting tools. (opens in a new tab)

  9. Development and characterisation of nano-multilayer CrAlSiN coating systems for cutting tools

    Two types of CrAlSiN nano-multilayer coating were designed and synthesised on AISI M2 high speed steel. Selected coatings were also deposited on pre-nitrided M2 substrate to investigate the effect of duplex treatment. A series of type I CrAlSiN coatings, which have sharp interfaces between …

    birmingham Download PDF for Development and characterisation of nano-multilayer CrAlSiN coating systems for cutting tools (opens in a new tab)

  10. An investigation into interface behavior and delamination wear for diamond-coated cutting tools

    … this research is to enhance the diamond-coated cutting tool performance through fundamental understanding of the interface adhesion of chemical vapor deposition (CVD) diamond-coated tungsten carbide cutting tools. CVD diamond-coated cutting tools have the advantages of superior tribological …

    alabama Repository record for An investigation into interface behavior and delamination wear for diamond-coated cutting tools (opens in a new tab)

  11. Investigation of the wear and failure modes of surface engineered multipoint cutting tools

    … todate into the wear mechanisms associated with cutting tools have been undertaken on single point tools which invariably operate under conditions of high speed and stress. The application of PVD coatings has been claimed to confer great benefits in terms of tool life by reducing friction on the …

    dcu Download PDF for Investigation of the wear and failure modes of surface engineered multipoint cutting tools (opens in a new tab)

  12. Development of high temperature/oxidation- resistant PVD coatings for cutting tools using HIPIMS

    … lend themselves to the application of protecting cutting tools exposed to harsh environment such as the dry, high-speed machining of abrasive materials. This thesis discusses the literature supporting the project and pays tribute to the development of coatings that formed the foundation for the …

    sheffield-hallam Repository record for Development of high temperature/oxidation- resistant PVD coatings for cutting tools using HIPIMS (opens in a new tab) Download PDF for Development of high temperature/oxidation- resistant PVD coatings for cutting tools using HIPIMS (opens in a new tab)

  13. Saturation effects on mechanical excavatability of Roubidoux sandstone under selected rock cutting tools

    "This study investigated the differences in the cutting performance of two rock cutting tools in dry and saturated rock. For this purpose, a permeable quartzose sandstone was subjected to a series of full scale linear rock cutting tests, in both dry and saturated conditions, using a constant …

    must-thes Repository record for Saturation effects on mechanical excavatability of Roubidoux sandstone under selected rock cutting tools (opens in a new tab)

  14. An investigation of the machining performance and mechanisms with rake face textured cutting tools

    … the previous studies of using surface textured cutting tools to improve the cutting performance is reported. It is shown that cutting tool surface texture is a promising technology to reduce the friction at the tool-chip and tool-work interfaces and cutting tool wear in machining. However, a …

    unsw Repository record for An investigation of the machining performance and mechanisms with rake face textured cutting tools (opens in a new tab)

  15. DEVELOPMENT OF A COMPUTATIONAL MODEL TO INVESTIGATE THE THERMO-MECHANICAL BEHAVIOUR OF CUTTING TOOLS

    During machining, the cutting tool wears out and affects the machined surface quality and overall production cost. The prediction of tool wear and analysis of cutting mechanics has significant importance for process optimization and cutting-edge design. In this present study, an efficient FE …

    mcmaster Repository record for DEVELOPMENT OF A COMPUTATIONAL MODEL TO INVESTIGATE THE THERMO-MECHANICAL BEHAVIOUR OF CUTTING TOOLS (opens in a new tab)

  16. Wear Mechanisms in Cutting Tools for Machining Applications : Interfacial Phenomena, Characterization, and Relation to Performance

    Metal cutting technology plays an important role in the automotive and aeronautic sectors, both of whichare important for the Swedish economy. Both make use of traditional grey cast iron and difficult-to-machine materials like titanium alloys and compacted graphite iron. The tools used to machine …

    lund Repository record for Wear Mechanisms in Cutting Tools for Machining Applications : Interfacial Phenomena, Characterization, and Relation to Performance (opens in a new tab) Download PDF for Wear Mechanisms in Cutting Tools for Machining Applications : Interfacial Phenomena, Characterization, and Relation to Performance (opens in a new tab)

Page 1 of 15