Global ETD Search

Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.

Results

Showing 1 to 16 of 16 for “"ejector system"”.

  1. Experimental and Analytical Investigation of a Two-Phase Ejector Used for Expansion Work Recovery in a Transcritical R744 Air-Conditioning System

    … rejection pressure can be used to maximize the system performance. In addition, large throttling losses make R744 a suitable fluid for expansion work recovery. This study presents experimental and computational results obtained from a transcritical R744 air-conditioning system using a two-phase …

    uiuc Repository record for Experimental and Analytical Investigation of a Two-Phase Ejector Used for Expansion Work Recovery in a Transcritical R744 Air-Conditioning System (opens in a new tab)

  2. Experimental and Computational Investigation of the Effect of Swirling Flows on an Ejector With Cut Angled Entraining Diffuser

    … compared the performance of two subsonic air-air ejectors with multi-ring entraining diffusers. The first ejector system was investigated by Qi Chen in his thesis. It consists of a nozzle, mixing tube, and a Full Entraining Diffuser. The Full Entraining Diffuser was found to cause drag forces in …

    queens Repository record for Experimental and Computational Investigation of the Effect of Swirling Flows on an Ejector With Cut Angled Entraining Diffuser (opens in a new tab)

  3. Optimization of a high-efficiency jet ejector by computational fluid dynamic software

    … was performed to optimize high-efficiency jet ejector geometry (Holtzapple, 2001) by varying nozzle diameter ratios from 0.03 to 0.21, and motive velocities from Mach 0.39 to 1.97. The high-efficiency jet ejector was simulated by Fluent Computational Fluid Dynamics (CFD) software. A …

    tamu Repository record for Optimization of a high-efficiency jet ejector by computational fluid dynamic software (opens in a new tab)

  4. Noise and flow characteristics of linear arrays of circular jets and ejector flow systems

    … reduction and thrust performance of a two-nozzle ejector system with and without acoustic liners is described, and the results of a one-dimensional ejector analysis are reported.</p><p>The experimental data of the linear nozzle arrays are compared with measurements on a single nozzle of the test …

    utk-theses Repository record for Noise and flow characteristics of linear arrays of circular jets and ejector flow systems (opens in a new tab)

  5. A Comparative Study of Different Cooling/Dehumidification Systems Based on Compressor, Ejector, and Membrane Technologies

    Air conditioning and refrigeration systems for cooling and dehumidification are some of the largest consumers of energy with most of the systems using electricity or fossil fuels to operate. Additionally, refrigeration systems typically use refrigerants, which can deplete the ozone layer and …

    tamu Repository record for A Comparative Study of Different Cooling/Dehumidification Systems Based on Compressor, Ejector, and Membrane Technologies (opens in a new tab)

  6. Head augmentation in hydraulic turbines by means of draft tube ejectors

    … latter model was a laboratory scale hydropower system which demonstrated 20-31 per cent head augmentation under various conditions. The numerical model was used to generate performance maps of full scale, low-head systems in the range from 200 to 500 kW. The performance maps were then used in a …

    vt Repository record for Head augmentation in hydraulic turbines by means of draft tube ejectors (opens in a new tab)

  7. Geoejector : extracting geothermal fluid from a low-pressure geothermal well

    … a low-pressure and low-enthalpy well, a subsonic ejector system (referred to as subsonic geoejector) was developed and tested at the Theistareykir Geothermal Field in 2020 and 2021. The system connected a low-pressure geothermal well to a nearby high-pressure well to induce flow from the …

    reykjavik Repository record for Geoejector : extracting geothermal fluid from a low-pressure geothermal well (opens in a new tab)

  8. Increasing the efficiency of geothermal power plants using optimum pressures for turbocompressors and steam jet ejectors in gas extraction systems

    … unless actively removed by some gas extraction system. Because these gases contribute significantly to the total backpressure on the turbine, it is in the interest of power generation to remove them from the condenser. The industry standard for removing these non-condensable gases has been steam …

    msu Repository record for Increasing the efficiency of geothermal power plants using optimum pressures for turbocompressors and steam jet ejectors in gas extraction systems (opens in a new tab)

  9. Potentials for COP increase in vapor compression systems

    … for COP increase in vapor compression systems: work recovery ejectors, condenser subcooling and increase of relative size of heat exchangers (HXs). Regarding work recovery ejectors, experimental results showed that the COP of the ejector system increased between 8.2% and 14.8% when …

    uiuc Repository record for Potentials for COP increase in vapor compression systems (opens in a new tab)

  10. Hybrid thermoelectric ejector - refrigeration system

    … to predict the refrigeration performance of an ejector powered by waste energy from a thermoelectric cooler. The model is based on constant pressure mixing process and considers the effect of frictional loss, viscous effect and shock wave phenomenon. Using this model, effects of nozzle exit …

    missouri Repository record for Hybrid thermoelectric ejector - refrigeration system (opens in a new tab)

  11. A General Simulation of an Air Ejector Diffuser System

    … facility exists to validate facility control systems as well as predict problems with facility operation. One weakness in this computer model is the modeling of an air ejector diffuser system. Two examples of facilities that could use this ejector diffuser model are NASA Langley Research …

    ut-knoxville Repository record for A General Simulation of an Air Ejector Diffuser System (opens in a new tab)

  12. Experimental and Numerical Investigations of Annular Swirling Primary Flow in a Short Subsonic Air-Air Ejector with Entraining Diffuser

    … swirling flow in a short subsonic air-air ejector that can be found in helicopters, fixed wing aircrafts, ships and other applications was investigated experimentally and numerically under different inlet flow conditions and geometric parameters. These ejectors are attached to the exhaust …

    queens Repository record for Experimental and Numerical Investigations of Annular Swirling Primary Flow in a Short Subsonic Air-Air Ejector with Entraining Diffuser (opens in a new tab)

  13. Design and Control of Hydrogen Supply and Recirculation System for Proton Exchange Membrane Fuel Cell Systems

    Proton Exchange Membrane Fuel Cell (PEMFC) systems require more than the theoretically needed hydrogen (H_2) fuel gas in the anode supply system to achieve high performance and extended operating life. The ejector-based H_2 supply and recirculation system (HSRS) is superior to its mechanical …

    uvic Repository record for Design and Control of Hydrogen Supply and Recirculation System for Proton Exchange Membrane Fuel Cell Systems (opens in a new tab)

  14. Technologie výroby plastové pružné spony

    V současné době má plastový průmysl velmi široké využití a to díky možnosti plně automatizovaného procesu či vyšší efektivnosti výroby. Důvodem volby diplomové práce bylo pochopení celé problematiky procesu vstřikování plastů. Zadaná součást slouží k přichycení plachty, která chrání pracovníky ve …

    brno-tech Repository record for Technologie výroby plastové pružné spony (opens in a new tab)

  15. Parní turbina s ejektorem

    Diplomová práce je zaměřena na sladění spolupráce turbiny s ejektorem pracujícím společně do parní sítě. Práce obsahuje informace o těchto zařízeních i historický vývoj zařízení. Podstatou diplomové práce je termodynamický výpočet a návrh hlavních parametrů a rozměrů turbiny a ejektoru. Po té …

    brno-tech Repository record for Parní turbina s ejektorem (opens in a new tab)

  16. Technologie výroby základny přístroje z plastu

    Technologie vstřikování termoplastů má široké využití ve všech odvětvích spotřebního a elektrotechnického i automobilového průmyslu. Největší výhodou této výrobní technologie je velký stupeň automatizace a dobrá opakovatelnost výrobního procesu. Další výhodou je možnost recyklace vtokových zbytků a …

    brno-tech Repository record for Technologie výroby základny přístroje z plastu (opens in a new tab)