Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 63 for “"epoxy laminates"”.
-
Central delamination in glass/epoxy laminates
Thesis (Ph. D.)--Michigan State University. Department of Metallurgy, Mechanics, and Materials Science, 1990
-
Fatigue response of notched graphite--epoxy laminates
… and strength of notched quasi-isotropic graphite-epoxy laminates were recorded and related to the fatigue damage. Two different laminates [0,90,+45,-45]s (type A) and [ +45, 90, -45, 0] s (type B) were considered and the effects of stacking sequence were compared. Nondestructive testing techniques …
-
The time-temperature behavior of graphite epoxy laminates
… study on the time-temperature behavior of epoxy based continuous and elastic fiber reinforced composite materials and the feasibility of using the time-temperature analogy as an accelerated characterization method to predict the long-term behavior are presented. This is a two-pronged …
-
Accelerated viscoelastic characterization of T300/5208 graphite- epoxy laminates
… viscoelastic response of polymer-based composite laminates, which may take years to develop in service, must be anticipated and accommodated at the design stage. Accelerated testing is therefore required to allow long-term compliance predictions for composite laminates of arbitrary layup, based …
-
Effect of high velocity oblique impacts on carbon/epoxy laminates
… stage. In this work, the behaviour of carbon/epoxy laminates subjected to high velocity oblique impacts is studied. Impact tests at the edge and centre of quasi-isotropic IM7/8552 laminates using a 3 mm steel cube projectile have been conducted over a range of velocities. The extent of impact …
-
Impact of Thermal Cycling on Carbon Fiber Reinforced Glass Epoxy Laminates
… the thermal cycling of the CF reinforced glass epoxy laminate samples and Flexural testing on the thermal cycled samples. Thermal cycling is performed on CF reinforced glass epoxy laminate samples with a range of -18 °C to 4 °C with a hold time of 10 minutes for each heating/cooling cycle. A set …
-
Tensile behavior of aluminum reinforced with angle-ply boron epoxy laminates
… of aluminum reinforced with angle-ply boron/epoxy laminates was conducted. It is shown that the ultimate stresses of a wide variety of laminate configurations fall within a very narrow range of values. Some configurations of composite reinforced aluminum laminates exhibited higher ultimate …
-
Fatigue behavior of notched carbon epoxy laminates during reversed cyclic loads
… strength were investigated for notched graphite epoxy laminates during fulIy-reversed cyclic loads. Two material systems, AS4/3501-6 and AS4/1808, two lamination arrangements, (0,45,90,-45)<sub>s</sub>₄ and (0,45,0,-45)<sub>s</sub>₄, and two notch configurations, central hole and opposing …
-
Effect of ply drop-offs on the strength of graphite-epoxy laminates
The strength reduction of a graphite-epoxy laminate due to dropping plies is investigated experimentally and analytically. Laminates were tested under uniaxial tension and compression. All the laminates were flat on one side with the plies dropped from the middle of a [( ± 45/0/90)<sub>s</sub> …
-
The effects of tensile preloads on the impact response of carbon/epoxy laminates
… weight impact tests were conducted on carbon/epoxy laminates under various magnitudes of uniform tensile stress. The composite plates were 8 ply (+45,0,- 45,90)<sub>s</sub> laminates supported in a clamped-clamped/free-free configuration. Tensile preloads from near zero to approximately 60% of …
-
Determination of material properties for progressive damage analysis in carbon epoxy laminates using Abaqus
Well-designed laminated composites do not fail suddenly but rather develop microscopic progressive damage that leads to changes in macroscopic material response, such as matrix cracks, stiffness reduction, and failure. Simulation techniques are able to predict damage initiation and evolution as a …
-
Residual Compressive Strength Prediction of Carbon/Epoxy Laminates Subjected to Low Velocity Impact Damage
Low energy impact damage to a composite structure is difficult to detect and can have profound effects on compressive strengths. Low energy impact damage is sometimes termed as barely visible impact damage (BVID). Detecting BVID is only possible by implementing nondestructive testing (NDT) …
-
Damage Assessment and Strength Predictions in S-Glass/Epoxy Laminates Subjected to Low Energy Impact
… sorting, and classifying how the composite laminates failed under compression after experiencing low energy/low velocity impact. Acoustic emission (AE) parameter data were collected during compression testing, and then inputted into an artificial neural network (ANN) for classification. …
-
Compression After Impact Load Prediction in Graphite/Epoxy Laminates Using Acoustic Emission and Artificial Neural Networks
… compression after impact (CAI) load of graphite/epoxy laminates from acoustic emission (AE) nondestructive testing (NDT) data. Thirty-four 24-ply bidirectional woven cloth laminate coupons were constructed and impacted at various energy levels ranging from 8 to 20 Joules, generating barely …
-
Tensile-tensile fatigue testing and fatigue properties of quasi-unidirectional non-crimp fabric reinforced glass-fibre/epoxy laminates
… non-crimp fabric (NCF) reinforced glass-fibre/epoxy laminates. These laminates have good fatigue performance since fibre bundles exhibit a very small amount of crimp. They are commonly used in fatigue critical structures, e.g. in spar caps of wind turbine rotor blades. The thesis is divided …
-
The development and evaluation of an experimental apparatus for the investigation of fastener pull-through failure in graphite-epoxy laminates.
… surface could be developed for the graphite-epoxy laminate. An expression was derived to predict the bending moment at the fastener in terms of the pull force on the fastener and the axial force in the plate. Aluminum specimens were tested and the results were compared with the predicted …
-
Comportamento em fadiga de laminados double-double de vidro/epóxi
… of two elastically in-plane equivalent glass/epoxy laminates suited for wind blade turbine applications: a quadriaxial (Quad) [±45/(0/90)3]s and a double-double (DD) [±15/±75]4T. Mechanical tests were performed under cyclic uniaxial tensile-tensile load using unnotched and open hole specimens. …
-
Analysis of shear test methods for composite laminates
… slotted specimen is studied for three graphite-epoxy laminates ([0], [90], [±45]<sub>S</sub>); the cross beam is studied for two graphite-epoxy laminates ([0/90]<sub>S</sub>, [±45]<sub>S</sub>); the Iosipescu and rail shear specimens are studied with several materials (steel, graphite-epoxy, and …
-
An ultrasonic test protocol for aramid aluminum laminates
… advanced epoxies and thermoplastics, composite laminates began appearing in high-performance aircraft around 1970. The boron-epoxy speed brake on the McDonnell-Douglas F-15A was one of the first such applications. With better control of the graphitizing process, high-stiffness, micron-sized …
-
A probabilistic approach to the Critical Element Model for fatigue in composite materials
… the fatigue behavior of cross ply Carbon Epoxy laminates is derived from a Monte-Carlo simulation.
Page 1 of 4