Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 42 for “"front axle"”.
-
A Study Towards the Removal of the Relay Rod in Volvo Trucks: Exploring Solutions for Steering the Second Front Axle in a Future Double Front Axle Arrangement by Wire
… in Volvo Trucks, specifically focusing on the front axle arrangement with two nondriven steered front axles (FAA20). The relay rod, a mechanical link between the axles in the steering system, presents structural and manufacturing challenges. The investigation aims to replace the currently in …
-
Weigh-in-Motion Auto-Calibration Using Automatic Vehicle Identification
… at highway locations to record vehicle weights, axle spacing, vehicle class, travel speed, vehicle length, and traffic volume. These data elements support effective transportation planning, infrastructure design, and policy development. Therefore, it is important that WIM sensors supply accurate …
-
Automatic Guidance of Agricultural Vehicles at Higher Speeds
When the GPS sensor was mounted above the front axle of the vehicle, adequate guidance control was demonstrated at speeds up to 6.7 m/s. Moving the sensor rearward to a more practical location added phase lag to the system, and guidance control was less effective.
-
Relationships Between Parameters of Combine Design and Soil Compaction
… do cause soil compaction due to excessive axle loads and resulting ground contact pressures, which can substantially reduce soil productivity: Researchers have documented crop yield reductions up to 60%. Field observations, consisting of soil bulk density, cone index, and moisture content …
-
Modelling and control of active power steering systems for heavy trucks
… the logistics chain. Today’s trucks can take a front axle load of approximately 8 tonnes. To be able to maneuver at high front axle loads, the driver needs assistance from additional power sources. The additional power can be provided through different sources in different steering topologies: …
-
Numerical optimization methods for improving energy efficiency in Battery Electric Vehicles using wheel torques and steering angles
… by controls given to it in the form of the front axle steering angle and the individual wheel torques. A battery electric vehicle with four in-wheel motors is an over-actuated system where the control space has multiple control solutions for allocating the wheel torques and front axle …
-
Optimum Path Tracking of an Independently Steered Four Wheeled Mobile Robot
… steering angles by remembering the path of the front axle, given by navigational sensors. Simulation and experimental results are provided to validate the proposed algorithms. One simulation demonstrates the performance of the controller, while the second compares the maneuverability of the …
-
Optimization of the Control Strategy for a Range Extender Vehicle
… electric motors. One electric motor propells the front axle and the other one is connected to the combustion engine to generate electric power. The control is restricted by customer requirements due to the concept of the vehicle. A Model-in-the-Loop is created to simulate the control strategy with …
-
Lane Keep Assist System for Chevrolet Blazer
… hybrid architecture, the vehicle’s front axle is powered by a GM 2.0L I-4 Turbo engine coupled with a 9-spd automatic transmission and an eRAD motor is used to propel the rear axle. The primary goal of this thesis is to present the construction of a hybrid electric vehicle system …
-
A COMPARATIVE ANALYSIS OF COASTDOWN TESTING METHODS FROM AN ELECTRIC DRIVE UNIT ENGAGEMENT PERSPECTIVE USING A STUDENT-DESIGNED PARALLEL HYBRID ELECTRIC VEHICLE
… with an internal combustion engine on the front axle and an electric drive unit on the rear. This vehicle’s electric drive unit has a clutch that can be disconnected through the team-implemented controls system. To test two post-processing methods to account for the forces of the drive unit …
-
Development of Pole Impact Testing at Multiple Vehicle Side Locations As Applied To The Ford Taurus Structural Platform
… induced deformation. The findings show that the front axle and A-pillar regions are much stiffer than the CG and B-pillar areas to narrow rigid pole impact. The central CG region produced stiffness relations that correspond well with published broad-impact data when the effective crush width was …
-
Hybrid Vehicle Supervisory Controller Development Process to Minimize Emissions and Fuel Consumption in EcoCAR 2
… architecture with a B20 biodiesel engine-powered front axle and electric motor-driven rear axle. The primary goal of this work is to present a selection of the processes used by the controls team throughout the competition to define the control system requirements and platforms, model the …
-
Design of Suspension Systems and Control Algorithms for Heavy Duty Vehicles
… (such as tractors in agriculture), only the front axle is provided with a suspension. Typical applications of suspensions in off-highway industry include the cabin suspension (known as secondary suspension system) and the front axle suspension (known as primary suspension system). Up to now, …
-
Impacts of Battery Electric Vehicles on Axle load and Pavement Performance for Swedish Road
… weight and redistribute mass toward the steering axle. Existing flexible pavement standards in Sweden were calibrated to diesel vehicle loading and may be inadequate as heavy electric trucks enter the national freight fleet. This study derives axle loads from manufacturer specifications for a …
-
Tractive performance of high-horsepower wheeled tractors with low tire inflation pressures
… two ballasting conditions represented the same front-axle/rear-axle weight distribution using the minimum and the maximum of ballast. The drawbar pull produced by the tractor was measured by a drawbar pin load cell, while the axle torques were measured by means of strain gauges on their output …
-
Torque vectoring using e-axle configuration for 4WD battery electric truck: Utilizing control allocation for motion control and steer by propulsion
… using four individual motors on two separate e-axles, different coordination possibilities are available for motion control of the truck. This thesis focuses on using torque vectoring as a principle to allocate the requested global torque. Furthermore, a novel method mentioned to as steer by …
-
Concept design of a portal gear reduction upright for F150 Raptor
… cars. The most common solution is to change the axle ratio for ring and pinion, but the downside to this solution is it increases the torque in all components downstream of the ring and pinion, including the ring and pinion system itself. To avoid this a portal gear reduction system can be used …
Page 1 of 3