Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 32 for “"green body"”.
-
Formation of alumina features and cadmium chalcogenide coatings of single-walled carbon nanotubes
… have been investigated. The formation of the 'green body' upon drying of the alumoxane solution and its sintering to ceramic have been studied with regard to shrinkage and cracking. Physical mixtures of the two alumoxanes were investigated to determine optimum conditions for the controlled …
-
Constitutive Modeling of the Densification Process of Ceramic Powders Subjected to Cold, Quasi-Static Pressing
The consistent, uniform pressing of green bodies is a necessary part of producing high-quality, high-performance ceramics with predictable qualities and behavior. Undesirable density variation in the compacted ceramic powder causes variability in performance, failure to meet quality control …
-
Supercritical extraction of binder from multilayer ceramic capacitors
… suggest a mechanism that led to defects in these green ceramic bodies after the extraction process. Supercritical extraction with carbon dioxide at 10-40 MPa and 55-90[degrees]C was used to remove binder from multilayer green ceramic bodies. Defects such as cracking and delamination were …
-
Additive Manufacturing of Ceramics with Multiscale Heterogeneous Microstructure
… ceramics are often extruded for form a green body and then fired to a high density. However, two challenges are faced by the extrusion-based AM of ceramics with multiscale features. One is to depositing ceramics with submicrometer thickness. The other one is to embed microchannels in …
-
Vliv nízkoteplotní plazmy na zlepšení keramické technologie
… prášku bylo metodou suspenzního lití připraveno green body, které bylo následně slinuto jednostupňovým a dvoustupňovým slinováním. V rámci práce jsou podrobně popsány metody přípravy keramických vzorků a jejich hodnocení. Vyhodnocené experimenty prokázály, že plazmová technologie má pozitivní …
-
Failure analysis of green ceramic bodies during thermal debinding
… cycle. This thesis presents failure behavior of green MLCs as a function of changing body size and heating rate. This is then used to design rapid heating cycles. Furthermore, models are presented to qualitatively analyze the failure behavior in terms of the stresses and strength of the green …
-
Near-Net Shaping and Additive Manufacturing of Ultra-High Temperature Ceramics via Colloidal Processing
… particle packing, and strength of a ceramic green body. For difficult-to-densify ceramics such as the UHTCs, which find their place in extreme environment applications, precise control of each step of the manufacturing process is key. In this work, a fundamental study on the interaction …
-
Keramické materiály na bázi spinelu MgAl2O4 pro optické aplikace
… s nejvyšší relativní hustotou těles ve stavu „green body“. Jako poslední procesní krok byla použita pro optimalizovanou keramiku metoda izostatického lisování za tepla, díky které byla úspěšně připravena transparentní nedopovaná i dopovaná spinelová keramika. Nejvyšší naměřené hodnoty RIT (real …
-
Design and Testing of a Top Mask Projection Ceramic Stereolithography System for Ceramic Part Manufacturing
… layer is built upon the previous to produce a green body that can be sintered for a fully dense ceramic part. This thesis introduces a new approach to ceramic stereolithography with a top mask projection light source which is much more economical compared to current vector scanning methods. The …
-
Experimental and numerical study of silicon nitride for powder injection moulding
… powder distribution within the injection moulded green bodies which will be used to validate the numerical simulations. The differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) are developed to measure the volume fraction of ceramic powder in the feedstock and green bodies. …
-
ADVANCED MATERIALS PROCESSING FOR DENSIFICATION AND PERMEABILITY OPTIMIZATION AT ELEVATED TEMPERATURES
… molten medium and urea as the nitrogen source. Green bodies were prepared from commercial Si₃N₄ powder, compacted, and partially encapsulated before sintering in an air-filled furnace. Densification was assessed using Archimedes measurements, and microstructural evolution was characterized …
-
Advances in Processing of Transparent Lutetia-Based Ceramics for High Power Laser Applications
Conventional and scalable methods of green-body formation of powder compacts, along with temperature/pressure processing methods, were optimized to sinter Lu2O3 powder compacts to relative densities of 97-98%, with micrometer-sized grains. Post-HIPing at or below sintering temperatures yielded …
-
DEVELOPMENT AND TESTING OF ADDITIVELY MANUFACTURED COPPER MIXTURES FOR WARHEAD APPLICATIONS
… debinding and sintering depend on sufficient green-body porosity, complete binder removal, and sintering temperature. This study provides a foundation for developing Cu metal FFF filaments and production of shaped-charge liners.
-
Advancing Elastomers to Additive Manufacturing Through Tailored Photochemistry and Latex Design
… surrounded the particles and yielded a solid "green body" structure. Photorheology elucidated rapid photocuring behavior and tunable green body storage moduli based on scaffold composition. Subsequent water removal and annealing promoted particle coalescence by penetration through the scaffold, …
-
Synthesis of Ta-doped Li7La3Zr2O12 for application in solid-state electrolyte
… commercial powder. Systematic optimization of green body properties and sintering yielded ceramics with 95.8% relative density, 0.49 mS cm⁻¹ conductivity at 20 °C and 0.25 eV activation energy (20–40 °C). Furthermore, the study introduces a spray-drying synthesis approach for cubic-phase …
-
Characterization of Andrenocortical Tissue Morphology, Histology, and Steroid Synthesis Among Finetooth (<i>Carcharhinus isodon</i>), Blacktip (<i>Carcharhinus limbatus</i>), Atlantic Sharpnose (<i>Rhizoprionodon terraenovae</i>), and Bonnethead (<i>Sphyrna tiburo</i>) Sharks
… interrenal is a single yellow-white to dark green body along the kidney midline. Bonnethead sharks possess one thin strip of white tissue extending from the anterior potion of the kidney ending past the division of the kidney lobes. Histological assessment of cell type and 3bHSD expression …
-
Behavioral, temporal, and spatial relationships in free-ranging female Anolis carolinensis (Sauria: Polychridae)
… range volume, perched highest, and maintained a green body color most often. Females tended to perch on smaller diameter limbs and to perch higher than males.
-
Μελέτη δομής και ιδιοτήτων κονιομεταλλουργικά παραχθέντων σύνθετων μεταλλικών αφρών αλουμινίου
… production conditions (compact pressure) of the “green body”. Apart from that, a methodology of 3D design of the structure of the Al-MSFs is proposed based on Delaunay triangulation with FEM analysis. Appropriate equivalent electrical circuit and the mechanism of the early stages of corrosion of …
-
Understanding phase transformations during flash sintering
… flash sintering is described. The effects of green body resistance and selected flash parameters on the flash temperature and the resulting phases are shown. By studying reduction reactions as model systems and utilizing in situ Raman to monitor defects and phases, we can gain further …
-
Processing of Boron Carbide
… carbide powder including sintering optimization, green body optimization and sintering behavior of nano-sized boron carbide was investigated for the development of complex shaped body armor. Pressureless sintered B4C relative densities as high as 96.7% were obtained by optimizing the soak …
Page 1 of 2