Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 125 for “"high injection"”.
-
Bicmos delay analysis including high injection and base push-out effects
Master of Science (M.S.)
-
HIGH INJECTION PRESSURE DME IGNITION AND COMBUSTION PROCESSES: EXPERIMENT AND SIMULATION
… This can be addressed by a larger nozzle size or higher injection pressure. However, the effect of high injection pressure on DME spray combustion characteristics have not yet been well understood. In order to fill this gap, spray and combustion processes of DME were studied extensively via a …
-
HIGH INJECTION PRESSURE IMPINGING DIESEL SPRAY CHARACTERISTICS AND SUBSEQUENT SOOT FORMATION IN REACTING CONDITIONS
… vessel. The impinged spray was captured by a high-speed camera and the instantaneous spray propagation distance and rate were obtained. For a better understanding, the microscopic behavior of the spray propagation, the curvature of the impinged spray was calculated and a relationship between …
-
Macroscopic and microscopic characterization of non-reacting diesel sprays at low and very high injection pressures
En la exploración de nuevos métodos para el mejoramiento de la eficiencia y rendimiento del motor diésel, es claro que un gran esfuerzo debe estar enfocado en el proceso de inyección de combustible. La eficiencia de la combustión y las emisiones, se ven muy afectadas por el proceso de atomización, …
-
Experimental and numerical investigation of a high boost and high injection pressure Diesel engine concept for heavy duty applications
… system, a two-stage turbocharger and a 3000 bar injection pressure-capable Fuel Injection System. This thesis focuses on the experimental and numerical assessment of emissions and performances of this engine architecture over the Stage V certification procedure. It will be shown how the …
-
Spray characterization under flash boiling conditions of a DI multi-hole injector at high injection pressures in a combustion vessel
… injector applicable to the gasoline direct injection (GDI) engine. Tests were performed in a constant volume combustion vessel using a high-speed schlieren and Mie scattering imaging systems. Four fuels including n-heptane, 100% ethanol, pure ethanol blended with 15% iso-octane by volume, …
-
Light Injection from an Active Cladding to the Core of a Fiber Optic Fluorosensor
A fluorosensor works on the basis of light injection from the clad into the core of an optical fiber. The sensitivity of such a sensor depends on the efficiency of light injection. Conditions necessary for a high injection efficiency are experimentally determined. The refractive index difference …
-
Theory of conductivity modulation in semiconductors
… characteristics of the form: J α V at low injection levels, J α V² at high injection levels, and J α V³ at very high injection levels. Space charge is important in the cube law case. Models ignoring diffusion are shown to be valid only for extrinsic semiconductors. Bipolar neutral flow with …
-
A theoretical and experimental investigation of metal-semiconductor contacts
… theory by Borneman et. al. (1955) is extended to high injection levels by using the junction relations of Misawa (1955). Then the non-zero-electron-current theory is developed. This theory shows that 'a' is unity for low Injection Into extrinsic semiconductors and that a = (3b-M)/(b-M) for …
-
Analysis of and process development for high-frequency indium gallium phosphide/gallium arsenide heterojunction bipolar transistors
… These properties include the availability of highly selective etches, an energy band alignment favorable for high injection efficiency devices, and the absence of DX centers.
-
Η εκτίμηση της λειτουργικότητας της αριστερής κοιλίας με τη δοκιμασία κόπωσης
… into three groups according to their L.V. injection fraction. Each group combined patients with a low, medium, and high injection fraction. 424 patients had normal i.f. (53-75%) 1266 patients medium i.f. (45-55%), 410 patients low i.f. ↓ 45%). Using the injection fraction and the curve …
-
QUANTUM EFFICIENCY ENHANCEMENT FOR GAN BASED LIGHT-EMITTING DIODES AND VERTICAL CAVITY SURFACE-EMITTING LASERS
… electron overflow and asymmetrical electron/hole injection were found to be the dominant reasons for efficiency degradation in nitride LEDs at high injection; (2) delta p-doped InGaN quantum barriers were employed to improve hole concentration inside the active region and therefore improve hole …
-
Simultaneous propagation of multiple fractures in a horizontal well
… increased the number of propagated fractures. Higher injection fluid viscosity significantly increased the fracture widths and slightly decreased the fracture lengths, but did not have any impact on the number of propagated fractures. Also, higher injection rates led to longer and wider …
-
Injection Impairment by Suspended Solids: Well Models, Filtration Parameters, and Models’ Validation with 3-D Injection Experiments
… permeability and loss of injectivity. Water injection, without solids suspension, at high velocity generates a loss of injectivity as a non-Darcy flow effect. The compounding impacts of high injection fluid velocity with suspended solids are expected to produce more severe injectivity loss …
-
Characterization of Coke Properties at Tuyere Level of an Operating Blast Furnace
… of different levels of supplementary oil injection. Coke samples were obtained through tuyere drilling and analysed using a range of analytical tools including XRD, SEM and high temperature reactors with emphasis on mineralogy, carbon structure and reactivity. Carbon structure was found to …
-
Effect of variable perforation configuration on proppant transport and distribution using slickwater, The
… heel stage. Injecting the fracturing fluid at a high injection rate creates the fractures and is followed by proppant-laden slurries to ensure the conductivity of the fractures. One of the main challenges in multi-stage, multi-cluster treatments is distributing the proppant evenly between the …
-
Progress Towards Competitive III-V Infrared Detectors: Fundamental Material Characterization and Techniques
… generated carrier density is dependent on the high-injection recombination mechanisms and not the minority carrier recombination, enabling accurate extraction of parameters governing high-injection recombination. From these measurements, it is found that the Shockley-Read-Hall lifetime is 3.47 …
-
Computer simulation of a ceramic core injection molding process
… industries, are made by ceramic injection molding. The high injection pressure, the high viscosity of the ceramic/wax mixture, and the high injection velocity during the injection molding process result in high rate of erosion, or wear, of the internal surfaces of die. The …
-
Systematic Extraction Flow and Gate Stack Development for GaN HEMT Devices with MVSG Model
Gallium Nitride (GaN) High Electron Mobility Transistors (HEMTs) are rapidly being featured as core components in modern high voltage and high frequency systems due to their wide band gap, high breakdown voltage, and superior electron mobility. New topologies and technologies are rapidly emerging …
Page 1 of 7