Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 191 for “"lap shear"”.
-
Structural Behavior of Lap Shear Connections with Thermally Insulating Filler Plates
… (RCSC 2014) suggests a reduction in the bolt shear strength when undeveloped fillers with a thickness of more than 0.25 inch are used while using any non-steel material is prohibited due the limited research available. Most research studies have investigated the mechanical behavior of thermal …
-
Characterization of Structural Adhesives Using Lap Shear and Pin and Collar Tests
… and a one-part epoxy (SA9850). Experimental lap shear tests were undertaken to identify optimum strength combinations between adhesives and adherend surface preparation. Each adherend was prepared using a variety of pretreatment methods including conversion coatings, anodization, mechanical …
-
Structural Evaluation of Hybrid Double-Lap Shear Bolted Connections Incorporating Additively Manufactured 316L Stainless Steel Inner Plates
This study investigates hybrid double-lap shear bolted connections incorporating additively manufactured 316L stainless steel inner plates, alongside conventionally produced reference plates, in single- and double-bolted configurations with different geometric design variables. The additive …
-
Fatigue behavior and structural stress analysis of coach-peel and lap-shear friction stir welded joints of AZ31 magnesium alloy
… this work the fatigue behavior of coach-peel and lap-shear friction stir linear welded joints of AZ31 magnesium alloy sheet were evaluated under different loads and the results were compared using structural stress analysis. Lap-shear coupons of 30 mm in width were obtained from a welded overlap …
-
A fundamental study on the structural integrity of magnesium alloys joined by friction stir welding
… the physical and mechanical properties of lap-shear joints produced using friction stir welding. This study focuses on understanding the effect of tool geometry and weld process parameters including the tool rotation rate, tool plunge depth and dwell time on the mechanical performance of …
-
Friction Stir Spot Welding of Ultra-High Strength Steel
… over time, less abrasive wear, and better lap shear fracture loads of the welds that were produced, compared to the other grades. This is explained by less exposure of the binder phase to wear by both adhesion and abrasion during welding of DP 980. A-type tools were the most consistent in …
-
Role of metal alkoxides as primers in polymer/metal adhesion
Steel is a material with a high tensile shear strength and is relatively inexpensive to produce. Further, it is widely used in industry and its use in adhesive bonding applications is increasing. Adhesively bonded structures offer several advantages over mechanical fastening such as reductions in …
-
BOND STRENGTH EVALUATION IN ADHESIVE JOINTS USING NDE AND DIC METHODS
… defects and reliably predicting the bond shear strength. As a result, adhesive bonding technology is still not solely implemented in primary structures of an aircraft. Therefore, there is a greater demand for a novel NDE tool that can meet the existing aerospace requirement for adhesive …
-
Friction Bit Joining of 5754 Aluminum to DP980 Ultra-High Strength Steel: A Feasibility Study
… 4340, or H13. Experiments were performed in lap shear, T-peel, and cross tension configurations, with the 0.070" thick 5754 aluminum alloy as the top layer through which the friction bit cut, and the 0.065" thick DP980 as the bottom layer to which the friction bit welded. All experiments were …
-
Adhesive bonding of stainless steel :Sstrength and durability.
… surface pre-treatments. Standard single overlap shear and floating roller peel tests conducted in ambient conditions were employed in the discrimination and the degree of compatibility between adhesive and adherend, as measured by the proportion of cohesive failure on the post-fracture face, …
-
Adhesive bonding of stainless steel : strength and durability
… surface pre-treatments. Standard single overlap shear and floating roller peel tests conducted in ambient conditions were employed in the discrimination and the degree of compatibility between adhesive and adherend, as measured by the proportion of cohesive failure on the post-fracture face, …
-
Towards Understanding the Effects of Current Input on Fatigue Mechanisms in Resistance Spot Welding of Advanced High Strength Steels
… TBF-1180. Welds were fabricated in a traditional lap shear geometry in order to investigate the effects of LME, while an hourglass shaped cap geometry was used for welds with microstructural variation. Fatigue testing revealed that for lap-shear coupons containing LME cracks, no deleterious effect …
-
Design and optimisation of adhesively bonded overlap joints
… The most common joint configuration is the lap shear joint, which has been investigated widely and several ideas have been proposed to improve its performance. For example, the introduction of fillets at the overlap ends or tapering of the substrates can reduce the peel stresses at the …
-
Investigation of resin infusion consumable effect on fusion bond strength in the manufacture of a thermoplastic vertical axis wind turbine prototype
… hypothesis was tested via manufacture of double lap shear strength coupons which were tested via ASTM 3528. Processing parameters of the bulk heating fusion bonding process were varied included temperature, consolidation pressure and time, and cooling method. Strength testing results in addition …
-
Surface characterization and adhesive bonding of carbon fiber-reinforced composites
… and scanning electron microscopy (SEM). Double lap shear and Boeing wedge configurations were used to evaluate the strength as well as the durability of the composites bonded with an epoxy film adhesive. Fluoropolymer residues which were found on the composite surfaces were fully removed by grit …
-
Friction Bit Joining of Dissimilar Combinations of DP 980 Steel and AA 7075
… by Honda. Joints were mechanically tested in lap-shear tension, cross-tension, and peel configurations. Joints were also fatigue tested, cycling between loads of 100 N and 750 N. The failure modes that joints could experience during testing include: head, nugget, material, or interfacial …
-
Development of High-Performance Epoxy-Based Nanocomposite Adhesive Materials for Structural Integrity
… of carbon nanomaterials and BCP addition on the shear strength of the adhesive joints was studied by conducting single lapix shear tests. The bond thickness of 0.15 mm was maintained to achieve maximum joint performance. The lap shear strength of the adhesive joints was found to have increased …
-
An experimental and numerical investigation of refill friction stir spot welding of aerospace aluminium alloys
… and mechanical properties of AA2024-T3 lap joints produced at welding times significantly below those previously reported in the literature. Various microscopy techniques were used to assess weld microstructure and defect evolution, while mechanical properties were determined through …
-
Experimental Testing and Modelling of Adhesively Joined T-structures
… were undertaken including quasi-static direct shear (2.5 mm/min), quasi-static torsion (2.5 mm/min), unsupported dynamic impact shear (4.43 m/s) and supported dynamic impact shear (3.96 m/s). Surface preparation is an important component when assessing the strength of the adhesive. Grit …
Page 1 of 10