Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 45 for “"lateral bracing"”.
-
Top-lateral bracing systems for trapezoidal steel box-girder bridges
… support the weight of the fresh concrete. Top-lateral bracing systems are used to provide both strength and stiffness during construction. A method for the design of top-lateral bracing systems was developed through field and laboratory experiments conducted on full-scale trapezoidal steel …
-
Lateral Torsional Buckling of Wooden Beams with Mid-Span Lateral Bracing
… and numerical investigation is conducted for the lateral torsional buckling analysis of wooden beam with a mid-span lateral brace subjected to symmetrically distributed loading. Two models are developed; one for the case of a rigid brace and another one for the case of a flexible brace. The …
-
Lateral bracing forces in compressed two-span columns with initial curvature
… of this study is to find critical loads and full bracing conditions for perfect two-span columns, and to find the reaction forces at the lateral bracing supports and maximum deflections for two-span columns with initial curvature. In each case, the column under consideration may have different …
-
The effect of lateral bracing on the dynamic response of wood floor systems
… of an extensive study of several types of lateral bracing for solid-sawn and parallel-chord truss floor systems. Three solid-sawn floor bracing systems were evaluated: X-bridging, full-depth solid blocking, and finally, post-tensioned solid-blocking. Five different truss bracing systems …
-
Critical behavior of rectangular frames considering the influence of non-linear flexible connections and lateral bracing in the presence of primary bending moments.
… load. Further studies include the effect of lateral bracing on the critical behavior of framed structures. Both modes of buckling, symmetrical and anti-symmetrical, are considered. The critical load for the anti-symmetrical mode of buckling is found to be considerably lower than that …
-
Measured deflections of a four girder bridge under varying bracing conditions
… of bottom flange, impact factors on girders, and lateral load distribution from two different bracing conditions under a controlled load and normal traffic loads on the Holston River Bridge located in Knoxville, TN. The two controlled load tests performed were a crawl (static) and speed (dynamic) …
-
Bracing design requirements for inelastic members
Using properly spaced and designed bracing can substantially increase the buckling capacity of a member. A brace needs to satisfy both stiffness and strength requirement. Significant research has been done for the bracing requirements of elastic members. Relatively little work has been performed …
-
Load-Deformation Behavior of Tension-Only X-Brace Roof Truss Diaphragms
… subassembly specimens with tension-only rod bracing were conducted to determine the load-deformation behavior of the system. The first specimen used 7/8-in. rods, two types of hillside washers, two types of compression members, and two configurations of lateral bracing. The second specimen …
-
Stability and reliability analysis of metal plate connected wood truss assemblies
… describes a study on the stability capacity and lateral bracing force of wood beam-columns and metal plate connected (MPC) wood truss assemblies. A user-friendly computer program, SATA, was developed based on the finite element method (FEM). The program can be used to perform three-dimensional …
-
Design considerations for mid-rise steel frame structures using wood-based flooring systems
… structural weight, floor vibration and lateral bracing are considered for joisted and panel floors in steel building structures. The influence of joisted wood-based flooring systems on the seismic response of concentrically braced steel frame buildings is assessed based on linear dynamic …
-
A Study Rigid-Frame Design versus Truss-and-Column Design
… brevity the overall design of the building (sway bracing, lateral bracing, purlins, girts, roofing, siding, and bay spacing) was assumed to be the same for both designs. It is possible that this assumption cannot be made and the estimates of cost, therefore, are in error. In actual practice the …
-
Assessment of basic steel I-section beam bracing requirements by test simulation
… the required stiffness and strength for basic bracing of columns and of beams. Substantial evidence exists showing that the Appendix 6 equations provide an accurate characterization of the stability bracing requirements, particularly when various refinements from the AISC Commentary are …
-
Safety of Concrete Formwork to Wind Loading During Construction
… shape, height above the ground level, amount of lateral bracing, and location on safety will be investigated. The investigation includes the development of a model for predicting short-term wind velocities. A second model was also developed for the evaluation of uncertainties in falsework …
-
Evaluation of steel I-section beam and beam-column bracing requirements by test simulation
… provisions provide limited guidance on the bracing requirements for beam-columns. In cases involving point (nodal) or shear panel (relative) lateral bracing only, these provisions simply sum the corresponding strength and stiffness requirements for column and beam bracing. Based on prior …
-
Use of Cast Modular Components for Concentrically Braced Steel Frames
… research: (1) the Cast Modular Ductile Bracing system (CMDB); (2) the Floating Brace system (FB).The CMDB system makes use of cast components introduced at the ends and the center of the brace to produce a special bracing detail with reliable strength, stiffness and deformation capacity. …
-
Inelastic behavior of laterally supported steel beams subjected to cyclic loading
… behavior and the failure characteristics of laterally supported wideflange steel beaus which are subjected to alternating inelastic strains. It is essentially an extension of a study conducted by L. D. Ozier on similar beaus which had no lateral support. The primary purpose of the thesis is …
-
Net section rupture in tension members with connection eccentricity
… and similar sections are frequently used for lateral bracing and as truss elements. Such members will normally have eccentric connections, and it is often permitted, by current design specifications, to neglect this eccentricity in the design of the member. In this study, load tests were …
-
Toward improved flange bracing requirements for metal building frame systems
… of the AISC Direct Analysis Method for stability bracing design of columns, beams, beam-columns and frames. Emphasis is placed on out-of-plane flange bracing design in metal building frame systems. Potential improvements and extensions to the 2005 AISC Appendix 6 stability bracing provisions are …
-
Elastic stability of a pony truss
… of certain type of bridge without the top lateral bracing. A qualitative study of the question reveals, that the resist lag action of the web members is greatly affected by the magnitudes of their axel stresses; and this conclusion leads to the necessity of determination of web resistances …
-
Stability bracing behavior for truss systems
The stability bracing behavior of trusses was investigated using experimental testing and computational modeling. The laboratory experiments were conducted on twin trusses fabricated with W4x13 sections for the chord and web members. Spans of 48 and 72 feet were used in the tests that included both …
Page 1 of 3