Global ETD Search

Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.

Results

Showing 1 to 20 of 683 for “"loading rate"”.

  1. Loading Rate Effects on Axial Pile Capacity in Clays

    … can damage the pile and may not produce accurate results. There is a relatively new testing method called the Statnamic Testing Method which tests foundation piles at a very fast rate, but still slower than with dynamic tests. As the rate at which load is applied to a test pile increases, the …

    byu Repository record for Loading Rate Effects on Axial Pile Capacity in Clays (opens in a new tab) Download PDF for Loading Rate Effects on Axial Pile Capacity in Clays (opens in a new tab)

  2. The influence of loading rate on excess pore pressures in triaxial tests

    … in this dissertation is concerned with coupled loading and consolidation in triaxial tests and with selection of rates of loading in routine tests to avoid errors due to incomplete drainage or non-uniform pore pressures in fine grained soils. The work consisted of a combination of laboratory …

    city-london Download PDF for The influence of loading rate on excess pore pressures in triaxial tests (opens in a new tab)

  3. THE EFFECT OF LOADING RATE ON ANNULUS FIBROSUS STRENGTH FOLLOWING ENDPLATE FRACTURE

    … mechanical properties of AF specimens would show rate-dependent alterations in their tensile and adhesive strengths following endplate fracture. The purpose of the present study was to quantify the mechanical properties of the AF from IVDs that had sustained endplate fracture via different rates …

    wilfrid-laurier Repository record for THE EFFECT OF LOADING RATE ON ANNULUS FIBROSUS STRENGTH FOLLOWING ENDPLATE FRACTURE (opens in a new tab) Download PDF for THE EFFECT OF LOADING RATE ON ANNULUS FIBROSUS STRENGTH FOLLOWING ENDPLATE FRACTURE (opens in a new tab)

  4. Numerical modeling of steel fiber reinforced concrete composite exposed to high loading rate

    … dass die Festigkeit solcher Verbundwerkstoffe ratenabhängig ist, d.h. sie wird durch die Erhöhung der dynamischen Belastung stark beeinflusst. Dieser Effekt gilt sowohl für die Verbundwerkstoffkomponenten Beton und Stahlfasern als auch für die Verbundwechselwirkung zwischen ihnen. Das Phänomen …

    qucosa-diss

  5. A Numerical Investigation of Loading Rate Effects on Pre-Cracked Charpy V-Notch Specimens

    To quantify the effects of loading rate on ductile crack growth in CVN specimens, plane strain, finite element analyses are used to model ductile crack extension in specimens subjected to quasi-static and impact loading. The Gurson-Tvergaard dilatant plasticity model for voided materials describes …

    uiuc Repository record for A Numerical Investigation of Loading Rate Effects on Pre-Cracked Charpy V-Notch Specimens (opens in a new tab)

  6. Determining an Appropriate Organic Matter Loading Rate for a Created Coastal Plain Forested Wetland

    … native forested hydric soils. However, optimal loading rates for created wetland soil reconstruction have not been rigorously established. Our objective was to determine appropriate organic amendment loading rates for a Coastal Plain mitigation wetland based on 1) soil properties reflective of …

    vt Repository record for Determining an Appropriate Organic Matter Loading Rate for a Created Coastal Plain Forested Wetland (opens in a new tab)

  7. Laboratory Strength Testing of Argillaceous Limestone Under Varying Saturation, Scale, Loading Rate, and Confinement Conditions

    … The effects of specimen saturation, scale, loading rate, and confinement have been investigated through the laboratory strength testing of specimens representative of Cobourg limestone found at depth for the proposed low and intermediate level DGR site. Using standardized laboratory testing …

    queens Repository record for Laboratory Strength Testing of Argillaceous Limestone Under Varying Saturation, Scale, Loading Rate, and Confinement Conditions (opens in a new tab)

  8. Optimizing the design ammonia loading rate of submerged attached-growth reactors in warm and cold conditions

    … It is sized using a typical design maximum TKN loading rate (per unit volume of the SAGR). Historic studies have shown that nearly full TAN and TKN removal can be consistently achieved in SAGRs sized using these design parameters at very low sustained water temperatures of even less than 1°C. …

    manitoba Repository record for Optimizing the design ammonia loading rate of submerged attached-growth reactors in warm and cold conditions (opens in a new tab)

  9. Effect of soil loading rate on microbial activity during co-composting of diesel-contaminated clay soil

    … experiment was to determine the effect of soil loading rate on the microbial performance during active phase co-composting of diesel-fuel contaminated clay soil under simulated windrow composting conditions. Microbial performance was monitored through relative heat generation, volatile solids …

    manitoba Repository record for Effect of soil loading rate on microbial activity during co-composting of diesel-contaminated clay soil (opens in a new tab)

  10. Influence of Loading Rate and Shear-Displacement Magnitude on the Pore Pressure Generation at Sliding Surface

    要旨pdfファイル:タイトル「すべり面での過剰間隙水圧に及ぼす載荷速度及びせん断変位振幅の影響に関する研究」

    kyoto Repository record for Influence of Loading Rate and Shear-Displacement Magnitude on the Pore Pressure Generation at Sliding Surface (opens in a new tab)

  11. Mechanistic evaluation of geosynthetic interlayer performance in asphalt overlays: Effects of temperature, loading rate, and placement depth

    … of temperature (-20 °C, 25 °C, and 40 °C), loading rate (2 and 5 mm/min), and placement depth (one-third, one half, and twothirds from the specimen bottom), with the full rate-depth factorial conducted at 25 °C and 40 °C. Performance parameters include stiffness indices (K0-4mm and K̄ 10 …

    ets-quebec Download PDF for Mechanistic evaluation of geosynthetic interlayer performance in asphalt overlays: Effects of temperature, loading rate, and placement depth (opens in a new tab)

  12. The Influence of Hydraulic Loading Rate on Nitrification Performance in a Two-Stage Biological Aerated Filter Pilot Plant

    … one, ammonia oxidation stage two) biological aerated filter was operated for 10 months on-site at a domestic wastewater treatment plant. Over the study, the system was operated at different hydraulic loading rates that resulted in a range of applied organic and ammonia mass loadings. Performance …

    vt Repository record for The Influence of Hydraulic Loading Rate on Nitrification Performance in a Two-Stage Biological Aerated Filter Pilot Plant (opens in a new tab)

Page 1 of 35