Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 22 for “"microcomposite"”.
-
Development of polyimide/metal gradient microcomposite films
… soluble metal compounds in an effort to create microcomposite films in which the location of the composite structure was controlled; namely at the film interfaces. Two different modification techniques were used in this study, in-situ chemical generation and infusion deposition. Results indicate …
-
Study of a microcomposite metal-doped polyimide adhesive
It is widely held in the field of adhesion science that the properties of the interfacial region, or interphase, between two bonded surfaces are of critical importance to the performance of an adhesive bond. This thesis describes a study in which a polyimide was modified by the addition of metal …
-
Poly(amide acid) infusion with Copper(II) Chloride to form polyimide microcomposite films
Polyimides are well known for their high thermal stability, chemical inertness, and their high electrical resistance. These properties make them ideal for use in the aerospace and electronics industries. Often polyimides are modified by coating or doping the films with metal species to change the …
-
Synthesis of Functionalized Polysiloxanes and Investigation of Highly Filled Thermally Conductive Microcomposites
… networks. The intention was to generate stable microcomposite dispersions with very high concentrations of polar thermally conductive fillers. Lightly crosslinked elastomeric networks with controlled amounts of polar moieties were prepared via a hydrosilation curing mechanism. High …
-
Processing-Structure-Property Relations in Novel Organocement Composites
… from CaAl$\sb2$O$\sb4$-coated Al$\sb2$O$\sb3$ microcomposite powders were fabricated. These composites contained a negligible amount of unreacted CaAl$\sb2$O$\sb4$ and a moderate reduction in bulk polymer content and exhibited initial strengths comparable to those reported for conventional …
-
Polylactic Acid (PLA) containing Talc Microparticles and Amorphous Polyhydroxyalkanoates (aPHAs) for Improved Barrier and Mechanical Properties in Food Packaging
… to be transported through a nanocomposite or a microcomposite by the same solution-diffusion mechanism, the barrier properties in the two cases should be the same as long as the volume fraction of the two fillers is the same and the aspect ratio of the two platelets is the same. Validating this …
-
Terahertz microjets for spectroscopy on the subwavelength scale
… spheres are then manufactured out of custom THz microcomposite materials and experimentally characterized in terms of the focusing performance. Finally, the dielectric spheres are demonstrated in a spectroscopic application to show the improvement in resolution.
-
Modelo numérico multiescala para previsão da curva tensão-deformação de aços dual phase pelo método tensão RVE
… by combustion. DP steel is considered to be a microcomposite with a biphasic microstructure composed of islands of hard and resistant martensite dispersed in the ductile and soft ferritic matrix, which provides mechanical properties demanded by the mobility industry with a good cost-benefit …
-
Preparation and characterisation of poly(ethylene terephthalate) and poly(vinyl alcohol)/clay nanocomposites.
… be dependent on the dispersion of the clay with microcomposite structures resulting in better barrier properties than their nanocomposite counterparts. Higher temperatures resulted in faster diffusion rates. During the diffusion of water crystalline regions of the PVOH were dissolved and the clay …
-
Multi-Functional Composite Materials for Catalysis and Chemical Mechanical Planarization
… This first objective involved the fabrication of microcomposites consisting of titanium dioxide (TiO2) nanoparticles confined within porous, microgels of a thermo-responsive polymer for use in the photocatalytic treatment of wastewater. TiO2 has been shown to be an excellent photocatalyst with …
-
Electric Field Alignment of Cellulose Based-Polymer Nanocomposites
… 50 KHz for duration of 20 minutes for the microcomposite and 250Vpp/mm, 10KHz for a duration of 1hr for the nanocomposite. At 0.4wt% concentration, 21% increase in dielectric constant for the optimal nanocomposite case. Above Tg, a 680% improvement in elastic modulus at 0.4wt% concentration …
-
Evaluation of corrosion resistance of different steel reinforcement types
… the performance of corrosion resistance for MMFX Microcomposite steel reinforcement, a high-strength, high chromium steel reinforcement, is evaluated. The study presented herein presents the separate field and laboratory studies of ongoing research at Iowa State University to determine if in fact …
-
Injection Molding of Pregenerated Microcomposites
… concerned with injection molding pregenerated microcomposites composed primarily of poly(ethylene terephthalate) (PET) as the matrix and HX1000 as the thermotropic liquid crystalline polymer (TLCP). Several factors were examined to maximize the mechanical properties of these composites, …
-
Carbon nanotube - Polymer nanocomposites & Activated charcoal - Polymer microcomposites
… and characterisation of five novel polymer nano/microcomposites. Separate sets of single wall carbon nanotubes (SWCNT)-poly (vinyl alcohol) (PVA) and COOH functionalised multi wall carbon nanotubes (MWCNT)-PVA nanocomposite films of 50–80 μm were fabricated through solution-cast; similarly, …
-
Novel composite materials synthesized by the high-temperature interaction of pyrrole with layered oxide matrices
… first members of a new class of heterogeneous microcomposites characterized by incomplete occupancy by the metal oxide core of the volume encapsulated by the rigid, amorphous permeable polymeric membrane that reproduces the volume of the initial grain of precursor substrate. The method may be …
-
The processing of microcomposites based on polypropylene and two thermotropic liquid crystalline polymers in injection molding, sheet extrusion, and extrusion blow molding
… liquid crystal polymers (TLCPs), referred to as microcomposites. The processing methods used are injection molding, sheet extrusion, and extrusion blow molding. The TLCPs used are HX6000 and Vectra A950. The microcomposites are produced by drawing strands of PP and TLCPs generated by means of a …
-
Επεξεργασία και αξιοποίηση μηχανολογικών πολυμερών από απορρίμματα ηλεκτρικού και ηλεκτρονικού εξοπλισμού
… (XRD): mixed intercalated/exfoliated and microcomposite structure. The second one is formed at much lower percentage and is ascribed to the degradation of surfactant on the clay or to its transfer from the clay to the matrix or/and to the change of the surrounding tension during the melt …
-
Development of bioinspired hyaluronan enhanced synthetic polymers for medical applications
… polyethylene glycol (PEG). HA was used to form a microcomposite on the surface of the non-woven polypropylene while PEG was grafted to the surface with oxygen plasma. The resulting materials were evaluated for their tensile mechanical properties, breathability, chemical composition, …
-
Cure and Conductivity: Investigation of Thermal Processing of Silver Nanobelt - Epoxy Composites
… 1) reduced total filler content compared to microcomposites, resulting in reduced cost; 2) improved final conductivity; 3) improved longevity due to high nanobelt stability. The current work is focused on several studies of electrically conductive composites, and of silver nanobelts: 1) …
Page 1 of 2