Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 36 for “"moire interferometry"”.
-
Analysis of composite laminates by Moire interferometry
Thesis (Ph. D.)--Michigan State University. Department of Materials Science and Mechanics, 2000
-
Replication of Gratings for Use in Moire Interferometry
Moire interferometry is a technique for the measurement of small displacements using the interference pattern produced by two gratings. One of the gratings must be attached to the surface of the specimen where the measurements are to be taken. A process recently developed produces a grating on the …
-
Determination of residual stress using phase shift Moire interferometry.
… research, a combined hole-drilling/phase shift moire interferometry method was applied to determine the residual stress state. This new method overcomes the drawbacks of the conventional hole-drilling/strain-gage method in that it has the advantage of high sensitivity full field measurement. For …
-
Extension of Moire interferometry into the ultra-high sensitivity domain
… per fringe contour, which corresponds to that of moire with 20,000 lines per mm, in combination with spatial resolution of the optical microscope (2-5 μm). The objective was achieved by the following developments. First, the basic sensitivity of moire interferometry was increased beyond the …
-
Developments in moire interferometry: carrier pattern technique and vibration insensitive interferometers
… to answer the questions. It has been proved that moire interferometry is a powerful technique in the study of composite materials. The high sensitivity and resolution of a measurement technique is the key to determining the properties of a material which has a fine and complicated structure such …
-
Environmental-assisted fracture behavior of iron aluminides using Moire interferometry with digital image processing.
… under air, oxygen or water environment. Moiré interferometry was applied to obtain whole-field displacement, crack growth rate, stress intensity factor, and crack-tip strain fields. A digital image processing (DIP) procedure was developed to obtain the strain distributions. Test results showed …
-
Development of a Virtually Calibrated Projection Moire Interferometry Technique Capable of Inaccessible Surface Measurements
… on the submicron scale. Projection Moiré Interferometry (PMI) is an out-of-plane displacement measurement technique, and consists of capturing reference and deformed images of a grid pattern projected on the test object. By differencing the reference and deformed images of the projected …
-
Study of Sn-Ag-Cu reliability through material microstructure evolution and laser moire interferometry
… using microstructure evolution, laser moiré interferometry and finite-element modeling. A particle coarsening based microstructure evolution of the solder joint material during thermal excursions was studied for extended periods of time lasting for several months. The microstructure evolution …
-
Calculation of energy release rates for delaminations in composite materials using phase shifting moire? interferometry
… enhancement of the optical technique of moire? interferometry, including alternative grating technology, image processing of fringe patterns, the implementation of phase shifting and the automation of the data reduction process. The improvements provided a practical experimental means for …
-
Interlaminar Deformation at a Hole in Laminated Composites: A Detailed Experimental Investigation Using Moire Interferometry
… composite specimens was measured using new moire interferometry techniques. These new techniques were developed and evaluated using a 7075-T6 aluminum control specimen. Grating replication techniques were developed for replicating high quality diffraction gratings onto the cylindrical …
-
An experimental study of frictional phenomena around the pin joints of plates using moire interferometry
… at VPI & SU, is employed: high-sensitivity moiré interferometry. Using a clearance pin-joint model made of prototype structural material, Aluminum 7071-T6, studies on frictional phenomena between the pin and plate are conducted to provide a comprehensive treatment of the following subjects: …
-
Induced strain of actuation of surface bonded and embedded piezoceramic patches
… voltage/strain response was characterized using moire interferometry and Twyman-Green interferometry techniques. Moire interferometry experiments were conducted to investigate the induced strain of actuation in a flat plate with two surface bonded piezoceramic patches and a flat plate with one …
-
Determination of stress concentration factors using experimental methods
… brittle specimen failure, photoelasticity, and Moire interferometry. Results are compared to each other and to finite element analysis performed on the same geometry. Strain gaging and photoelasticity were chosen as the best methods for stress concentration factor determination.
-
Integration and processing of high-resolution moiré-interferometry data
A new hybrid method combining moire interferometry, high resolution data-reduction technique, two-dimensional datasmoothing method, and Finite Element Method (FEM) has been successfully developed. This hybrid method has been applied to residual strain analyses of composite panels, strain …
-
Effects of layer waviness on compression-loaded thermoplastic composite laminates
… fatigue life were determined experimentally. Moire interferometry was used to investigate the disturbance in the displacement fields and the modes of deformation associated with layer waviness under compression loading. The state of stress in the vicinity of the layer waves and the influence …
-
A crack closure study on 2024 T351 aluminum alloy by the Moire method
… displacements by using the high sensitivity Moire interferometry technique was evaluated. The stress intensity factor determination using the crack opening displacements was studied. The data on the crack opening displacement were used to obtain the crack-tip-opening load of a fatigue crack …
-
Interlaminar deformations on the cylindrical surface of a hole in laminated composites: an experimental study
… of the panels. The experimental technique of moire interferometry was extended to take measurements of in-plane deformations on singly-curved surfaces. A replication scheme was developed to produce high-frequency diffraction gratings on singly-curved surfaces. Two different techniques were …
-
An evaluation of the Iosipescu specimen for composite materials shear property measurement
… conventional strain gage instrumentation and moire interferometry is performed. A finite element analysis of the Iosipescu shear test for unidirectional and cross-ply composites is used to assess the uniformity of the shear stress field in the vicinity of the notch, and demonstrate the effect …
-
Local Displacements and Load Transfer of Shape Memory Alloys in Polymeric Matrices
… in epoxy were measured using heterodyne microinterferometry. The interfacial bond strengths from the pullout tests were correlated with the maximum wire displacements. The transient load transfer behavior of a one-way SMA ribbon in a room temperature cured polymer matrix was quantified using …
Page 1 of 2