Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 80 for “"plasma arc"”.
-
Design of an Air Stabilized Plasma Arc
The plasma-arc generator (see figure 1, 2) has been used for several years as an invaluable ground test facility in which the gas stagnation properties of hypervelocity flight may be reproduced. The plasma is produced by shorting an electric arc between two electrodes; then directing a gas stream …
-
A multi-stage distributed energy plasma arc railgun
… and testing of multi-stage distributed energy plasma arc railguns are presented. In collaboration on an Air Force Office of Scientific Research (AFOSR) funded Multidisciplinary University Research Initiative (MURI) project, the Center for Pulsed Power and Power Electronics (P3E) at Texas Tech …
-
Characterisation of plasma arc technology processed waste products
Plasma arc technology is a novel method that widely applied in industry for the hazardous waste vitrification. After the plasma arc process, the wastes are transformed into inert and glassy materials ready for storage or other applications. The aim of this project is to characterise a plasma arc …
-
Laser lap welding of 80Y90T steel with plasma arc augmentation
… Using a CO<sub>2</sub> laser, it is shown that Plasma Assisted Laser Welding (PALW) can provide increased fusion zone width, when compared to conventional CO<sub>2</sub> welding, even in the presence of poor part fit-up. The negative effects of material gap, on PALW and laser only welds, are …
-
Numerical Modeling of the Metal Cutting Process in the Plasma Arc Cutting
The process of cutting metal with a plasma arc cutting tool is investigated and discussed. Focus is on the metal cutting process at the inside surface of the kerf. This is an important region that is not well documented due to the difficulty of experiments and the complexity of computation needed …
-
Study of Additive Manufacturing of Hastelloy X Using Plasma Arc Welding Technology
Plasma arc welding was implemented for additive manufacturing of Hastelloy X wire due to its potential to produce thin-wall structures for a high-temperature resistance of Hastelloy X. Single-layer beads were deposited to study and optimize the effects of arc length, nozzle size, shielding gas flow …
-
Modelling and efficiency improvement of a plasma-arc gasification reactor quench probe
… flow characteristics inside a laboratory scale plasma-arc gasification reactor quench probe with the aim of efficiency improvement. "Thermal efficiency" was mainly described according to the thermal and fluid profiles and characteristics inside the quench probe, while the chemical efficiency, …
-
Quantification of the heat transfer during the plasma arc remelting of titanium alloys
Plasma-arc cold hearth melting (PAM) is an important technology used in the melting process for titanium alloys. Compared to the more common, electron beam cold hearth re-melting process, PAM allows an inert gas environment which significantly reduces the evaporation rate of alloying elements. To …
-
Three-dimensional modeling of the plasma arc and metal transfer in arc welding
"Most previous three-dimensional modeling work on arc welding focused on the weld pool dynamics. Almost all these weld pool models were based on the two-dimensional axisymmetric Gaussian assumptions of arc pressure, plasma heat flux, and/or current density. They may not represent the real situation …
-
Numerical modeling of the work piece region in the plasma arc cutting process
The plasma arc cutting process is widely used for the cutting of metals. The process, however, is not fully understood and further understanding will lead to further improvements. This work aims to elucidate the fundamental physical phenomena in the region where the plasma interacts with the work …
-
Plasma-arc synthesis of ultra-fine aluminum-nitride powder for electronic-packaging applications
Includes bibliographical references (pages 159-165).
-
Study of the influence of the plasma torch in a plasma arc melting furnace
Plasma arc melting, PAM, is used to melt and refine titanium, a reactive alloy often used in the aerospace industry. This thesis looks at the effect of the properties of a plasma torch within PAM, focusing on its use as a mechanism for inputting energy to the ingot. Previous research has failed to …
-
Non-catalytic plasma-arc reforming process of methane with carbon dioxide for hydrogen production
… and save on valuable fossil fuel. This research project evaluates the Non-catalytic Plasma-arc Reforming Process for the production of synthesis and hydrogen gas. Carbon dioxide was used as the oxidizing agent instead of steam that is normally used in the Steam Methane Reforming Process. The …
-
Deploying plasma arc reforming to a commercial coal to liquid process : a techno-economic study
… One re-design option would be to integrate plasma arc reforming (PAR), which converts greenhouse gases in by-product streams to syngas. Redesigning a coal to liquid process to use PAR instead of auto thermal reforming has the potential to improve carbon efficiency, reducing emissions and …
-
Additive Manufacturing with Stellite 6 Metal-Cored Wire by Gas Tungsten Arc Welding and Plasma Arc Welding Methods
… alloy. These wires can be used with Wire and Arc Additive Manufacturing methods such as GTAW and PAW. These methods use a lower cost, and less complex heat source compared with Laser and Electron-Beam Processes. In this study, Stellite 6 metal-cored wire was utilized with GTAW to determine …
Page 1 of 4