Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 204 for “"plastic hinge"”.
-
Plastic hinge length in high-rise concrete shear walls
… concrete shear wall depends on the length of the plastic hinge. Typical building codes and several researchers recommend the use of an equivalent plastic hinge length at the base equal to half the wall length. However, the plastic hinge length is also influenced by parameters other than the wall …
-
Analytical Development of A Plastic Hinge Detail for Steel SMFs
A modular plastic hinge seismic special detail has been developed for use in steel special moment frames (SMFs). The aim of the special detail design is to dissipate seismic energy through stable yielding of a beam "link" in plastic hinge region. Reliable and repeatable energy dissipation at high …
-
Automatic plastic-hinge analysis and design of 3D steel frames
A rather complete picture of automatic plastic-hinge analysis onto steel frames under static loads is made in the present thesis. One/two/three-linear behaviours of mild steel are considered. The frames are submitted to fixed or repeated load. The geometric nonlinearity is taken into account. The …
-
Shifted Plastic Hinge Column Connections Using Grouted Sleeves for Accelerated Bridge Construction
… and experimentally tested using a shifted plastic hinge (SPH) concept to minimize the damage in the capacity-protected elements and retain the column ductility. The column testing matrix considered aspect ratio, moment gradient, and splicing details. Column models were tested in an upright …
-
Development of Shear Plastic Hinge Models for Analysis of Reinforced Concrete Members
The lumped plasticity analysis approach is one of the most efficient methods to calculate the nonlinear behavior of reinforced concrete (RC) structures. However, the number of models that can capture shear effects using this approach are limited, and the existing models mostly require iterations or …
-
Developing a Plastic Hinge Model for RC Beams Prone to Progressive Collapse
The US General Service Administration (GSA) 2013 Guidelines specify the procedures and the minimum requirements for the design and evaluation of the new and existing buildings against progressive collapse due to an instantaneous removal of vertical load bearing elements (i.e., columns). The …
-
In-Ground Plastic Hinge Analysis for Piles Used in Marine Oil and LNG Terminals
… the current recommendations for the in-ground plastic hinge length and depth for piles in section 7 of MOTEMS for all typical soil properties and pile dimensions found in Marine Oil and LNG Terminals. The pile types considered in this analysis are 24-inch octagonal prestressed concrete piles …
-
Evaluating the Effect of Decking Fasteners on the Seismic Behavior of Steel Moment Frame Plastic Hinge Regions
A series of full-scale beam-to-column moment connection tests were completed to determine the effects of powder actuated fasteners (PAF) and puddle welds on the seismic behavior of steel moment connections. In seismic regions, PAF are currently prohibited in the connection region (referred to as …
-
Evaluation of plastic hinge models and inelastic analysis tools for performance-based seismic design of RC bridge columns
… notion of an equivalent region under constant plastic curvature, i.e., the plastic hinge length (Lp), has been the main approach for evaluating the inelastic response of reinforced concrete (RC) columns for seismic bridge design. Most of the proposed Lp models have been calibrated on columns …
-
Seismic Performance Design Criteria of Existing Bridge Bent Plastic Hinge Region and Rapid Repair Measures of Earthquake Damaged Bridges Considering Future Resilience
… the moderate splice length that ensured flexural plastic hinging and the low longitudinal steel ratio that resulted in significant rocking at the column-footing interface. Furthermore, flexural cracking of the accompanying spread footing and splice failure of the column dowel bars were also …
-
Ductility of Reinforced Concrete Masonry Shear Walls
… achieved through the development of a flexural plastic hinge at the base characterized by yielding of the vertical reinforcement. The length of the plastic hinge and the ultimate curvatures within this region are the essential parameters affecting the ductility and ultimate displacements of …
-
Seismic performance of full-scale reinforced concrete columns
… among various ductility parameters. Measured plastic hinge lengths of column specimens were also affected by the shear span-to-depth ratio and axial load. The plastic hinge length of concrete columns was investigated by studying the compressive strain profile of the core concrete. An …
-
Plastic Hinging Behavior of Reinforced Concrete Bridge Columns
… deformations generally occur over a finite hinge length. A model of hinging behavior in reinforced concrete bridge columns will help guide proportioning, detailing and drift estimates for performance-based design. Data was collected during the NEESR investigation of the seismic performance …
-
Experimental Testing and Reliability Analysis of Repaired SMA and Steel Reinforced Shear Walls
… with SMAs in the boundary zones within the plastic hinge region and other control wall reinforced with conventional steel only. The repair procedure included removal of damaged concrete within the plastic hinge region, replacing fractured and buckled reinforcement, followed by shortening of …
-
Design of composite haunch beams and connections for long span applications
… of composite haunch beam can be achieved when plastic hinge occurred at haunch toes followed by at the mid-span to form a plastic collapse mechanism. Haunch toe could be designed as the weakest section to form a plastic hinge with suitable amount of reinforcement in the slab and range of haunch …
-
Pretest 3-D finite element analysis of the girder-to-cap-beam connection of an inverted-tee cap beam designed for seismic loadings
… a moment resistant connection and allow a plastic hinge to form in the top of the column. By allowing a plastic hinge to form in the top of the column the system is more economical then the current design detail.</p>
-
Experimental Testing of Axially Loaded Fuse Plates Without Continuous Buckling Restraint
… deformation away from the column and allow a plastic hinge to form in the beam. This plastic hinge prevents collapse but leaves the building difficult to repair. Some proprietary moment frame connections address this issue with replaceable fuse plate connections. These fuse plate connections …
-
Design of One-Story Hollow Structural Section (HSS) Columns Subjected to Large Seismic Drift
… using three design methods: elastic design, plastic hinge design, and pinned base design. First, for elastic design, the compression and flexural strength of the HSS columns are calculated according to the AISC specifications, and the story drift ratio that causes the interaction equation to …
-
Modeling the behavior of shear-critical reinforced concrete columns under lateral loads
… deformability of such columns, the definition of plastic hinge length was reassessed through consideration of yield penetration effects. The required confined zone in critical regions of columns and piers undergoing lateral sway during earthquakes is related to the plastic hinge length where …
-
Effect of near-fault ground motion characteristics on bridges with footing uplift
… though the damping of the structure and plastic hinge development at a specific location. Plastic hinge development, within limits, helps to improve the safety of people. However, recent research indicates that plastic hinging due to near-fault earthquakes is more significant than that …
Page 1 of 11