Global ETD Search

Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.

Results

Showing 1 to 20 of 48 for “"point loads"”.

  1. Elastic-Plastic Analysis of Tapered Beams Subjected to Point Loads

    Made available in DSpace on 2014-12-10T17:25:22Z (GMT). No. of bitstreams: 1 6406031.pdf: 5129364 bytes, checksum: 7639bd08b9567d895102c2c72a588447 (MD5) Previous issue date: 1963

    uiuc Repository record for Elastic-Plastic Analysis of Tapered Beams Subjected to Point Loads (opens in a new tab)

  2. Flexural Behaviour of Nail-Laminated Timber Panels Subjected to Concentrated Point Loads

    … panels were fabricated and tested under center-point bending, where a specific number of laminations were loaded. The loaded laminations were observed to experience an apparent increase in flexural strength and stiffness due to the contribution of unloaded laminations in the NLT panel, …

    carleton Repository record for Flexural Behaviour of Nail-Laminated Timber Panels Subjected to Concentrated Point Loads (opens in a new tab)

  3. Location of the Elastic-Plastic Boundary in Tapered Beams Subjected to Point Loads

    Made available in DSpace on 2014-12-04T23:11:06Z (GMT). No. of bitstreams: 1 6206248.pdf: 2829623 bytes, checksum: d3af01c48419d9fe6740a4852487e5d7 (MD5) Previous issue date: 1962

    uiuc Repository record for Location of the Elastic-Plastic Boundary in Tapered Beams Subjected to Point Loads (opens in a new tab)

  4. A Method for Approximating the Distributed Loads of an Airplane by Sets of Point Loads

    … determining the forces to be applied to these points which will simulate the load distributed over all the airplane.

    unt Repository record for A Method for Approximating the Distributed Loads of an Airplane by Sets of Point Loads (opens in a new tab)

  5. Analyses of Quasi-Isotropic Composite Plates Under Quasi-Static Point Loads Simulating Low-Velocity Impact Phenomena

    … obvious when laminates are subjected to impact loads. Due to these impact loads, laminates suffer visible and invisible damage. To improve the material performance in impact requires a better understanding of the deformation and damage mechanics under impact type loads. In thin composite …

    odu Repository record for Analyses of Quasi-Isotropic Composite Plates Under Quasi-Static Point Loads Simulating Low-Velocity Impact Phenomena (opens in a new tab)

  6. Composite Open-Web Trusses with Metal Cellular Floor

    … 50 ft. and were loaded by two symmetrical point loads. Different types of shear connectors and different degrees of connection were used. Tests results are shown and compared with analytical results obtained from elastic theories. An ultimate strength design method is proposed.</p>

    mcmaster Repository record for Composite Open-Web Trusses with Metal Cellular Floor (opens in a new tab)

  7. Design criteria for strength and serviceability of inverted-T straddle bent caps

    … ledge depth, web reinforcement, number of point loads, web depth, and shear span-to-depth ratio. The dissertation focuses on the effects of ledge length, ledge depth, number of point loads, and developing design criteria for strength and serviceability of inverted-T beams. Most inverted-T …

    texas Repository record for Design criteria for strength and serviceability of inverted-T straddle bent caps (opens in a new tab)

  8. Point Load Distribution in Overhang Slabs: Effects of Model Complexity and Load History

    Understanding the distribution of point loads in overhang slabs is crucial for improving design and assessment of reinforced concrete bridges. The concept of an effective width allows shear forces and bending moments to be evaluated at critical sections and used in the dimensioning of the slab. …

    chalmers Repository record for Point Load Distribution in Overhang Slabs: Effects of Model Complexity and Load History (opens in a new tab)

  9. Application of digital calibration technique on global bidirectional interconnects in integrated circuit

    … has increased the overall size of chips to the point where global interconnects between sub-units are becoming harder and harder to route and meet timing rules and requirements. The traditional way of routing interconnects and the use of uniform, unidirectional, point to point busses may no …

    texas Repository record for Application of digital calibration technique on global bidirectional interconnects in integrated circuit (opens in a new tab)

  10. ANALYTICAL STRIP METHOD FOR THIN CYLINDRICAL SHELLS

    … solution method can handle any combination of point loads, uniform loads, hydrostatic loads, sinusoidal loads, patch loads, and line loads applied in the radial direction. The results of the ASM are compared to results from existing analytical solutions and numerical solutions for several …

    uky-thes Repository record for ANALYTICAL STRIP METHOD FOR THIN CYLINDRICAL SHELLS (opens in a new tab)

  11. Shear cracking in inverted-T straddle bents

    … ratio, ledge height, ledge length, number of point loads, and member depth. This report focuses mainly on results from a first series of tests conducted within this experimental program.

    texas Repository record for Shear cracking in inverted-T straddle bents (opens in a new tab)

  12. Destructive Testing and Finite-Element Modeling of Full-Scale Bridge Sections Containing Precast Deck Panels

    … was subjected to flexural yield and failure. Point loads were applied and removed in increments, and dynamic testing was conducted at each load level. It was found that significant damage is somewhat noticeable by monitoring the changes in natural frequencies.

    utahstate Repository record for Destructive Testing and Finite-Element Modeling of Full-Scale Bridge Sections Containing Precast Deck Panels (opens in a new tab)

  13. Stability of a shallow planar truss model under multiple loads

    … subjected to multiple, independent, quasi-static point loads. Stability boundaries are determined for three different height-to-span ratios. The load sustaining capabilities increase greatly as the height-to-span ratio is increased. Stable branches of the load-deflection path are determined with …

    vt Repository record for Stability of a shallow planar truss model under multiple loads (opens in a new tab)

  14. Continuous Concrete/Cold-formed Steel Composite Beams Utilizing Joist Attachment to Support Offset Loading

    … the proposed LDM effectiveness. Three point loads were applied to each specimen and four roller supports were used to provide the reactions. Load was applied incrementally until failure was observed in the specimen. This loading was used to simulate story loads bearing directly on the …

    sdstate Repository record for Continuous Concrete/Cold-formed Steel Composite Beams Utilizing Joist Attachment to Support Offset Loading (opens in a new tab)

  15. Development of interactive computer programs for mechanical engineering design: fatigue analysis, section properties, and beam analysis

    … Uniformly or linearly varied distributed loads, concentrated point loads, applied moments, or combinations of all three may be applied. This program allows any combination of pinned, fixed, free, or guided flexural boundary conditions, even normally kinematically unstable condition can be …

    vt Repository record for Development of interactive computer programs for mechanical engineering design: fatigue analysis, section properties, and beam analysis (opens in a new tab)

  16. Design of reinforced concrete inverted-T beams for strength and serviceability

    … length, quantity of web reinforcement, number of point loads, member depth, and shear span-to-depth ratio. A strut-and-tie design method proposed by Birrcher et. al (2009), initially calibrated for compression-chord loaded deep beams, was investigated. It was concluded that the strut-and-tie …

    texas Repository record for Design of reinforced concrete inverted-T beams for strength and serviceability (opens in a new tab)

  17. COMPUTER INTERPRETATION OF HOLOGRAPHIC AND SHEAROGRAPHIC FRINGES

    … under uniform pressure or subjected to central point loads can be determined from holographic and shearographic fringes respectively. When applied to nondestructive testing, the size and depth of square and circular debonds in laminates can be accurately estimated for specimens tested under …

    nus Repository record for COMPUTER INTERPRETATION OF HOLOGRAPHIC AND SHEAROGRAPHIC FRINGES (opens in a new tab) Download file for COMPUTER INTERPRETATION OF HOLOGRAPHIC AND SHEAROGRAPHIC FRINGES (opens in a new tab)

  18. Experiments on a Hybrid Composite Beam for Bridge Applications

    … and FRP shell. Testing was performed by applying point loads on simple span beams (before placing the bridge deck) and a three beam skewed composite bridge system. Curvature from strain data is used to find internal bending forces, and the proportion of load within the arch is found. Additionally, …

    vt Repository record for Experiments on a Hybrid Composite Beam for Bridge Applications (opens in a new tab)

  19. Investigation of a hybrid bridge girder with reinforced concrete web and steel flanges

    … bridge specimen was subjected to two equal point loads at the third points. The behaviour of the test specimen was studied under service loads and increasing load until failure. Many aspects of the bridge test specimen behaviour were investigated. Perhaps the most important one was the …

    ubc Repository record for Investigation of a hybrid bridge girder with reinforced concrete web and steel flanges (opens in a new tab) Download PDF for Investigation of a hybrid bridge girder with reinforced concrete web and steel flanges (opens in a new tab)

  20. Computer aided design and analysis of cold formed sections

    … loading conditions where the number of supports, point loads, and uniform distributive loads can be specified by the designer. The profile can then be checked for suitability for the specified type of loading. Artificial Intelligence concepts have been introduced to give the designer decision …

    aston Download PDF for Computer aided design and analysis of cold formed sections (opens in a new tab)

Page 1 of 3