Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 155 for “"polymethylmethacrylate"”.
-
Elution of Metronidazole and Gentamicin from Polymethylmethacrylate Beads
Ten polymethylmethacrylate (PMMA) beads containing metronidazole (3 concentrations); gentamicin sulfate; or metronidazole and gentamicin sulfate were immersed in 5 ml of phosphate buffered saline in triplicate. Eluent was replaced at specified time intervals for 1 day (1, 3, 6, 12 and 24 hours), …
-
Characterization of a Lab-Scale Polymethylmethacrylate and Gaseous Oxygen Hybrid Rocket
… propulsion was conducted using optically clear polymethylmethacrylate and gaseous oxygen with a nozzle designed to achieve Mach 2. Characterization was performed using combustion simulations available from NASA and measurements with pressure transducers, thermocouples, a load cell, and …
-
Porous polymethylmethacrylate cement: development and evaluation of a potential implant material
Promotores : F. Driessens en T. Slooff
-
Chronic Ocular Hypertensive Model using Microbead Injection in Rats: Comparison of Polyurethane, Polymethylmethacrylate, and Polystyrene
… [7- and 17-µm polyurethane (PU), 7- and 15-µm polymethylmethacrylate (PMMA), and 15-µm polystyrene (PS)] and selected the appropriate microbeads for a chronic ocular hypertensive model in terms of IOP elevation and adverse events. IOP changes were observed for 4 weeks after microbead …
-
Processing history induced birefringence and the mechanical behavior of anisotropic filaments of virified polymethylmethacrylate and polystyrene
… behavior of anisotropic filaments of vitrified polymethylmethacrylate and polystyrene. Oriented filaments have been prepared by melt spinning and by oven drawing. Analysis of the internal stresses in the filaments indicates that even though the overall birefringence is made up of contributions …
-
Biomechanical analysis of vertebral body load-to-failure after cement augmentation with polymethylmethacrylate cement augmentation performed using two different techniques
Introduction Cement augmentation is a commonly performed procedure by spine surgeons as well as interventional radiologists. The ultimate goal of cement augmentation is to aid a vertebral body in resisting axial stresses. Understanding the difference between traditional and modern techniques in …
-
Biomechanical analysis of vertebral body load-to-failure after cement augmentation with polymethylmethacrylate cement augmentation performed using two different techniques
IntroductionCement augmentation is a commonly performed procedure by spine surgeons as well as interventional radiologists. The ultimate goal of cement augmentation is to aid a vertebral body in resisting axial stresses. Understanding the difference between traditional and modern techniques in …
-
Characterization of Surfactant Effects on the Visible Spectroscopy of Lanthanide Metal Ion-Triphenylmethane Dye Complexes (Microscopy, Polyvinylidene Fluoride, Electron, Polymethylmethacrylate, Blends)
Although both micellar and submicellar concentrations were considered, adding the nonionic surfactant Triton X-100 to the Gd('+3)-CAS complex had little effect.
-
The Thermal Degradation of Polymer Blends of Polyacrylonitrile
… and of blends of polyacrylonitrile and polymethylmethacrylate is studied in detail in Chapter 3. The decomposition of polymethylmethacrylate is shown to undergo significant changes upon blending. The effect has been found to vary with blend composition and has been attributed to reaction …
-
Flow behavior of molten polymer blends
… polyvinylacetate-polystyrene, polymethylmethacrylate-low Mw-polystyrene, polymethylmethacrylate-high Mw-polystyrene), crystalline polymers (polyethylene-polypropylene) and combinations of non-crystalline-crystalline polymers (polyethylene-polystyrene). Two methods of sample …
-
Strength Development at Incompatible Polymer Interfaces
… Three pairs of polymers were used: polystyrene-polymethylmethacrylate, polystyrene-co-acrylonitrile-polymethylmethacrylate, and polystyrene-co-acrylonitrile-polycarbonate. For each pair, the weld strength, as measured by G$\sb{\rm IC}$, attained a constant value which increased with welding …
-
Effect of carbon filler characteristics on the electrical properties of conductive polymer composites possessing segregated network microstructures
… focused on making composites consisting of a polymethylmethacrylate matrix, with various carbon fillers. The fillers that were examined were 3 different carbon blacks: N-550, N-772 and pureblack, and short multi-wall carbon nano-tubes. The carbon fillers were coated onto the …
-
An investigation of the reacting and non-reacting flow characteristics of solid fuel ramjets
… flow characteristics of solid fuel ramjets. Polymethylmethacrylate fuel grains were burned in a ramjet motor on a thrust stand. Combustion efficiency, regression rate profile and pressures were determined for the reacting flows and compared to pro- files obtained in non-reacting flows for …
-
Ultrafast Photoisomerization Dynamics of Photochromic Molecular Switches Affected by Their Environment and Ultrafast Energy Transfer
… transient absorption spectroscopy on thin polymethylmethacrylate (PMMA) films doped with azobenzene (AB) derivatives called for an improved experimental setup and data collection strategy combined with a background subtraction scheme. The vibrational cooling in the electronic ground state …
-
Experimental investigation of surface temperatures of some polymers in unlubricated sliding
… polytetrafluoroethylene, polystyrene, and polymethylmethacrylate were investigated. Effects of load and sliding speed on the friction and wear behavior of the polymers were examined. Finally, the experimental results were compared with theoretical calculations, and reasons for the …
-
PROTON BEAM WRITING OF MICRO/NANO FLUIDIC DEVICES FOR DNA ANALYSIS AND PARTICLE SEPARATION
… (PDMS) through soft lithography, polymethylmethacrylate (PMMA) are very popular for micro/nanofludic fabrication because of the easy process and low cost. In this thesis, different types of molds (resist, OrmoStamp and nickel mold) were fabricated for PDMS and PMMA fluidic devices …
Page 1 of 8