Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 18 of 18 for “"pull-out strength"”.
-
Pull-Out Strength of Fiberglass/Epoxy Composite RebarFabricated on a Three-Dimensional Braiding Machine
… betweenmanufacturing parameters and tensile pull-out strength of the rebar. The strength of the bondbetween concrete and FRP rebar was investigated using the pull-out test detailed by ACI 440.3R-12. The rebar was a No. 4 size and produced by combining multiple tows of fiberglass/epoxyprepreg …
-
Experimental and numerical investigations of pull-out strength of timber joints with glued-in rods
Timber joints with glued-in rods have several advantages with respect to mechanical connections, such as higher stiffness, more uniform stress distribution, less bar corrosion problems and better appearance. This thesis describes experimental and numerical studies of timber joints made with glass …
-
Experimental Determination Of The Pull-Out Strength Of Cast-In Lifting Inserts In Precast Hollow-Core Plank
… and it was post installed using non-shrink grout into the top of a hollow-core plank shortly after it was extruded. A literature review was also performed to further analyze the insert and to formulate analytical expressions capable of reliably predicting this tensile (pull-out) capacity of …
-
Effects of Biologics on Pedicle Screw Fixation in a Sheep Model: Histological and Biomechanical Analysis
… ovine spine model. Biomechanical pull–out strength, undecalcified histology, microradiography, and quantitative histomorphometry were used to assess effects of augmentation with rhBMP–2 on the holding power and peri–implant bone formation. Methodology: rhBMP–2 (0.43 mg/ml) soaked …
-
ASSESSMENT OF PORTLAND-LIMESTONE CEMENT FOR STRUCTURAL APPLICATIONS
… kinetics; mechanical properties including strength development, elastic modulus, and tensile strength; dimensional stability properties including drying shrinkage and creep; and structural properties for precast prestressed concrete including Mostafa strand pull-out strength, transfer …
-
Sensitivity studies on the shear lag parameter β using analytical and numerical techniques
The strength of fiber-reinforced composites is dependent on the strength of the fiber-matrix interface bond. Thermal, chemical, and other means have been used to modify the surface of fibers, resulting in increased fiber-matrix interface bond strength. However, researchers are still dependent on …
-
Textile Reinforced Concrete: Design Methodology and Novel Reinforcement
… carbon textile material (TRC beams). The tensile strength of textile reinforcement and pull out strength of TRC were measured. Four-point bending tests were performed on 76 beams (small and large scale beams). Several parameters such as volume fraction and reinforcement layout were studied in …
-
Fibre reinforced concrete in shear and flexure
… into the effect of steel fibres on the shear strength of concrete beams and slabs containing no transverse reinforcement is presented. Eight slab elements were tested in the UBC Element Tester and eight beams were tested under third point loading. A number of combinations of concrete strength …
-
Evaluation of Osseointegration Between Two Different Modalities of Hydroxyapatite Implant Surface Coatings: Plasma Sprayed HA Coated Implants and Electrophoresis Deposited Nano HA Coated Implants
… of osseointegration was inferred by interfacial strength and percent tissue-contact length.Materials and Methods: Thirty-six cylindrical implants (18 PS and 18 EPD) were placed into dog mandibles. Nine implants from each group were evaluated with pull out testing and histological studies at 12 …
-
INVESTIGATING CHLORIDE INGRESSION IN CONCRETE AND CHLORIDE-INDUCED REBAR CORROSION
… parameters, steel mass loss, and rebar pull-out strength. Results indicate that FFA reduces the corrosion rate by enhancing pore structure, while SN delays corrosion by increasing chloride threshold levels. Numerical simulations depict crack initiation and development due to rust …
-
Studies on rotator cuff repairs
… of rotator cuff tears has improved patient outcomes, the rotator cuff often re-tears. The aim of this thesis was therefore to investigate rotator cuff repair, particularly with respect to preventing re-tear. Methods: A shoulder strength testing device was designed and built specifically to …
-
Experimental characterization of the mechanical consequences of a debonded total hip stem with an unsupported distal tip
… within the cement mantle were measured. Stem pull-out tests were performed before the specimens were loaded and after each load case. Finally, the cement mantles were examined for damage.;The compressive creep tests of Simplex P bone cement indicate that this cement has a relatively high …
-
High Performance glued-in rod connections for Cross-Laminated Timber (CLT) structures
… connections determine the stiffness and strength of the structures. Glued-in rod connections are one of the frequently used connections in timber engineering due to their large load capacity, good fire and corrosion performance (because of the concealed rods), and aesthetically pleasing …
-
Continuum-based Multiscale Computational Damage Modeling of Cementitous Composites
… numerical algorithm is coded using the user subroutine UMAT and then implemented in the commercial finite element analysis program Abaqus, and the overall performance of the proposed model is verified by comparing the model predictions to various experimental data on macroscopic level. Using the …
-
Η επίδραση της χορήγησης α-τοκοφερόλης στην οστική ενσωμάτωση των ορθοπαιδικών εμφυτευμάτων από ανοξείδωτο χάλυβα και στο οξειδωτικό stress
… implants in rats as determined by (1) pull-out strength and removal torque and (2) a histomorphological assessment of bone formation. In addition, we investigated, (3) the correlation between the administration of alpha-tocopherol and the reduction in postoperative oxidative stress that …
-
Development of fire sprinkler system design for buildings with exposed timber surfaces
… “Timber in Construction Roadmap 2025”, sets out an ambition for timber to play a significant role in reducing the use of concrete and steel in construction. The first phase of the study focused on optimizing the wetting potential of sprinkler systems in rooms with exposed timber surfaces as …
-
Orthodontic mini-implants: morphological/structure characteristics and in vivo performance in animals
… stress generation and distribution, and pullout strength of commercially available orthodontic mini-implants (OMIs). In order to investigate the possible association of the findings and their clinical significance, four different OMIs systems were placed in early preadolescent pigs. …