Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 159 for “"pumping power"”.
-
Design, Construction, and Qualification of an Open Loop Wind Tunnel Facility to Quantify Enhanced Heat Transfer/Pumping Power Performance in Isothermal Rectangular-Cross Section Passages
Hydrocarbon-fueled and nuclear power plants are generally located near rivers, lakes or oceans so that water may be used to condense the turbine cycle working fluid. Since geothermal power plants must be located near their thermal source, air must be used to condense the working fluid when …
-
Electric Vehicle Battery Thermal Management Using Liquid Cooling
… slight expense of increased pressure drop and pumping power. Changing the spacing between batteries also had an effect on maximum temperature, pressure drop, and pumping power. The 0.75x ST set-up had the lowest maximum temperature values and the 0.75x SL set-up had the lowest pressure drop and …
-
Effects of particle concentration and surfactant use in convective heat transfer of CuO nanofluids in microchannel flow
… transfer rates, pressure drop, mass flowrate and pumping power for all fluids. These results show a heat transfer improvement for nanofluids of 8-16% over pure water, with no meaningful increase in pumping power. This result is highly desirable, as it indicates an easily obtainable heat transfer …
-
Performance of plate fin compact heat exchangers
… heat transfer rates between two fluids and the pumping power required to overcome fluid friction and push the fluids through the heat exchangers. In gas flow heat exchangers, the friction power limitations force the designer to select moderately low mass velocities. Low mass velocities with low …
-
ELECTROHYDRODYNAMICS (EHD) PUMPING OF LIQUID NITROGEN APPLICATION TO SPOT CRYOGENIC COOLING OF SENSORS AND DETECTORS
… Most of these applications require modest power dissipation capabilities while having stricter requirements on the spatial and temporal temperature variations. Controlled surface cooling techniques ensure more stable and uniform temporal and spatial temperature distributions that allow …
-
FORCE FED MICROCHANNEL HIGH HEAT FLUX COOLING UTILIZING MICROGROOVED SURFACES
Among other applications, the increase in power density of advanced electronic components has created a need for high heat flux cooling. Future processors have been anticipated to exceed the current barrier of 1000 W/cm<super>2</super>, while the working temperature of such systems is expected to …
-
Thermal Management with Supercritical Carbon Dioxide under Extreme Applications
… in thermal system design is minimizing the power required to operate cooling systems while maintaining effective heat removal. Traditional cooling systems utilize single-phase fluids where the heat transfer mechanisms are well understood. To meet a variety of cooling demands, a range of …
-
A feasibility study of heat transfer improvement in marine stream condensers.
… compared for heat load capability at constant pumping power, and for weight, volume, and estimated cost at an equivalent heat load. Results show that with the present condenser volume, the heat load can be increased by as much as 50 percent using heat transfer improvement techniques. From a …
-
A Feasibility Analysis of a Directly Sun-Pumped Carbon Dioxide Laser in Space
… for such applications as space communication and power transmission. In order to optically pump CO2 using sunlight, the intense vibrational-rotational absorption bands of CO2 in the 4.3 micron spectral region would have to be utilized. The total pumping power from sunlight can be calculated from …
-
Experimental evaluation of heat transfer and pressure drop performance of internally finned tubes.
… heat transfer area, but at the expense of high pumping power requirement. It is, therefore, suggested that quintuplex tube should be preferred in industrial applications in which the size of the heat exchanger is an important factor. But if the pumping power is the criterion for selection, the …
-
Investigation of heat and mass transfer in superhydrophobic microchannels with and without nanofluids
With the miniaturisation and increasing power density of electronic devices and energy systems, increasing the efficiency and effectiveness of heat removal is closely tied with technological advancement. Both microchannels and nanofluids have shown promise to enhance the internal convective heat …
-
Experimental Study of Microencapsulated Phase Change Slurry in Shell-and-Tube Heat Exchanger
… heat transfer performance but also increases the pumping requirements due to the exponential increase in viscosity along with particle concentration. The maximum average heat transfer coefficients of 5% and 7.5% mass fraction MPCS was 16.7% and 21.6% higher, respectively, than that of water under …
-
An Experiment on Integrated Thermal Management Using Metallic Foam
… comparable to past studies. In addition, the pumping power required was not excessive and would allow the thermal management system to be realized without an unreasonable energy input. Therefore, a metal foam heat exchanger integrated within the ducting of a variable cycle engine is deemed …
-
Numerical Study of Convective Heat Transfer in Flat Tube Heat Exchangers Operating in Self-Sustained Oscillatory Flow Regimes
… for the same Reynolds numbers. Data for required pumping power versus resultant Nusselt number were collected which showed four distinct operating regions for these devices spanning the low Reynolds number, steady flow region through the self-sustained oscillating flow region. Based on the data, …
-
A Heat Transfer Study Of SiO2 Colloid Flow In The Thermal Entry Region Of Mini Circular And Square Tubes
… and water was also compared at the same pumping power. This comparison evinced that at the same pumping power, water is a better heat transfer medium than SiO2 nanofluid. There was no observed effect of the hydraulic diameter on the heat transfer, and for the same hydraulic diameters …
-
Structurally Enhanced Electrodes for Redox Flow Batteries Produced via Electrospinning
… is not yet widely deployed owing to its low power density. This thesis describes the way of constructing the fibrous electrode with novel structure to overcome the flaw. The general electrospun materials of polyacrylonitrile were synthesized with substantially lower porosity than standard …
-
Thermo-Hydraulic Performance of Partially Blocked Metal-Foam Channels
… is the attendant higher pressure drop or pumping power penalty. This thesis was undertaken to investigate whether channels partially filled with metal foams can reduce the required pumping power with a minimal loss in thermal performance. The thermo-hydraulic (T-H) performance factor …
-
Pressure and thermal effects on superhydrophobic friction reduction in a microchannel flow
… becomes intrinsically high and a high pumping power will be required to drive the fluid. Since the pumping power delivered by portable devices is limited, one method to reduce this is to render the surface to become slippery. This can be achieved by roughening up the microchannel wall …
-
Enhanced active cooling of high power led light sources by utilizing shrouds and radial fins
Technological developments in the area of high power LED light sources have enabled their utilization in general illumination applications. Along with this advancement comes the need for progressive thermal management strategies in order to ensure device performance and reliability. Minimizing an …
-
General correlations for pressure drop and heat transfer for single-phase turbulent flows in ribbed tubes
<p>Heat exchangers are an integral part of any power plant, sometimes representing as much as one-third of the total investment. Recently, new techniques have been considered to increase the effectiveness of heat exchangers. Particular attention has been directed toward augmentation or enhancement …
Page 1 of 8