Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 23 for “"round tubes"”.
-
Effect of micro-fin geometry on flow and heat transfer during evaporation in round tubes
… flow pattern in transparent micro-finned tubes under both adiabatic and diabatic conditions. Rather than the conventional sight-glass method (without internal micro-fin geometry in the clear tube), clear resin tubes are made by a 3D printer to reproduce the real internal geometry in the …
-
Modeling heat rejection in horizontal smooth round tubes and experimental validation for R1234ze(E), R134a and R32
Heat transfer in condensers is typically divided into 3 zones: superheated, two-phase and sub cooled region. These regions, in general, are considered to be independent of each other and various correlations are available in literature to predict the heat transfer coefficient (HTC) in these regions …
-
Heat transfer and flow regimes during condensation in horizontal tubes
… condensation of refrigerants in horizontal tubes was conducted. Measurements were made in smooth, round tubes with diameters ranging from 3.14 mm to 7.04 mm. Four refrigerants were tested: R-12, R-22, R-134a, and azeotropic blends of R-32/R-125 in 50%/50% and 60%/40% compositions.
-
Supercritical Gas Cooling and Near-Critical-Pressure Condensation of Refrigerant Blends in Microchannels
… (ODP) refrigerant blends in small diameter tubes was conducted. The azeotropic refrigerant blend R410A (equal parts of R32 and R125 by mass) has zero ODP and has properties similar to R22, and is therefore of interest for vapor compression cycles in high-temperature-lift …
-
Heat transfer and visualization in large flattened-tube condensers with variable inclination
… on inclined, convective condensation in small, round tubes to large, non-circular tubes with low inlet mass flux of vapor. The steel condenser tube in this study was designed for use in a power-plant air-cooled-condenser array with forced convection of air. The tube was cut in half lengthwise …
-
Numerical Modeling of Failure in Magnesium Alloys under Axial Compression and Bending for Crashworthiness Applications
… behavior during axial compression tests of the round tubes of magnesium alloy, AZ31. A parametric study was also performed to investigate the effects of various phenomena on simulated results. Numerical modeling of square magnesium tubes during bending was also simulated for extruded magnesium …
-
Characteristics of the Liquid Film in Horizontal Two -Phase Flow
… is not currently available. Measurements for round tubes, square tubes in two orientations, and a triangle tube in two orientations are presented. Beyond the fundamental importance of these data sets, the results are used to show that the base liquid layer tends to behave in a manner analogous …
-
An Investigation into the Longitudinal Rolling of Tubes Through Two Grooved Rolls
… of the process of the longitudinal rolling of tubes through two grooved rolls with the aim of contributing to the full understanding of the mechanics of the process in order to increase its efficiency. The tubes which were unsupported internally, were rolled through an oval groove. Two types of …
-
Edge-defined, film-fed growth : a process evaluation
… to grow crystals in the form of thin ribbons, round tubes, square channels and airfoils. Dies of these configurations were constructed for this purpose.</p><p>3. A LiF/CaF<sub>2</sub> eutectic composition crystal was grown to study the growth interface characteristics and to explore the use of …
-
Flow visualization and pressure drop for refrigerant phase change and air-water flow in small hydraulic diameter geometries
… drop in horizontal small hydraulic diameter tubes was conducted. Co-current flow of air-water mixtures in four round tubes and one rectangular tube with hydraulic diameters ranging from 5.5 mm to 1.3 mm were investigated. Bubble, dispersed, elongated bubble, slug, stratified, wavy, …
-
Longitudinal flow between cylinders in square and triangular arrays
… correlated by the Nikuradse equation for smooth round tubes when the Reynolds number exceeded 10,000 and when the equivalent diameter, used in both the Reynolds number and the friction factor, was taken as four times the hydraulic raduis based on total wetted perimeter. In laminar flow no …
-
Design aspects related to noise in indirect heat pumps
… different types of heat exchangers, with flat tubes and round tubes, are designed and compared for suitability. Using relevant data and literature on heat transfer and heat exchangers, the necessary size (height, width and depth) and air flow of the different heat exchangers is calculated using …
-
Performance evaluation of louvered fin compact heat exchangers with vortex generators
… of a louvered fin heat exchanger with round tubes in a staggered layout can be improved by adding delta winglets to the fins. Such compound designs form the next generation of heat exchangers. Both experiments (flow visualizations in a water tunnel and heat transfer and pressure drop …
-
Development of capacitive sensor to determine void fraction in horizontal and vertical tubes
… and void fraction in horizontal and vertical tubes with R134a in the adiabatic condition and low mass flux range. Visualization results of horizontal flow patterns are compared to Wojtan-Ursenbacher-Thome flow regime map and have a good agreement. Both void fraction results for horizontal and …
-
Cascade and Secondary Coolant Supermarket Refrigeration Systems: Modelling and New Frost Correlations
… frost characteristics on flat plates and round tubes thereby determining the appropriate defrost periods. Cascade and secondary coolant refrigeration systems are the potential candidates to replace traditional ones due to the fact that the former can work on natural refrigerants and the …
-
AN INTEGRATED, MULTI-PHYSICS ANALYSIS AND DESIGN OPTIMIZATION FRAMEWORK FOR AIR-TO-REFRIGERANT HEAT EXCHANGERS WITH SHAPE-OPTIMIZED TUBES
… to consider small characteristic diameter HX tubes with novel shapes and topologies which were not feasible even a decade ago. These small diameter, shape-optimized tubes have been shown to perform the same job as existing HXs while offering significant and desirable improvements in …
-
An experimental study of critical heat flux with surface modification and its analytic prediction model development
… consistent with classic understanding of CHF in round tubes using water in relatively low pressure (less than 0.2 reduced pressures). In addition, a Fluid-to-Fluid scaling model was utilized to convert the test data obtained in the simulant fluid (R-134a) into the prototypical fluid (water). The …
Page 1 of 2