Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 21 for “"side shear"”.
-
Construction Effects on the Side Shear of Drilled Shafts
Design methods for side shear of drilled shafts, including the resistance factors that should be applied, do not account for any specific construction procedure. Instead, design often relies on analysis of case studies which include all construction methods used in each geomaterial type (e.g. …
-
Laboratory load tests of side shear for axially loaded piles
… HPX-piles have approximately 10 percent greater side shear capacity than conventional HP-piles, on average. Unit side shear and the side shear parameter [beta] for both smooth and textured piles generally increased with increasing effective stress and increasing over consolidation ratio. …
-
Time Dependent Effect of Drilling Slurries on Side Shear Resistance of Drilled Shafts
… excavated hole. These elements rely largely on side shear resistance generated by their substantial diameters and lengths to effectively transfer loads. Therefore, an exceptional concrete to soil interface is essential for proper performance of these structures. The FDOT preferred stabilization …
-
Developing LRFD Side Shear and End Bearing Resistance Factors for Design of Axially Loaded Drilled Shafts in Soil Containing Caliche Layers Using the Monte Carlo Approach
… layers The prime objective is to calibrate the side shear and end bearing resistance factors of axially loaded drilled shafts based on the soil characteristics of Nevada. The load-settlement responses of axially loaded drilled shafts installed as single piles are evaluated based on the 40 …
-
Evaluating the Effect of Temporary Casing on Drilled Shaft Rock Socket Capacity
… of this study was to determine the effect on side shear resistance in limestone when temporary casing is used. Due to testing in actual limestone being an unrealistic goal, simulated limestone mixes were prepared and cast into 6 – 42 in. diameter beds. Limestone throughout Florida can be quite …
-
An experimental study of the small strain response of sand
… in strain space. In small strain response, shear strains result mainly from shear stress increments and not from changes in stress ratio. Shear volume response is contractant for both an increasing and decreasing shear stress increment, whereas the sense of shear strain increment alternates …
-
Earth pressures applied on drilled shaft retaining walls in expansive clay during cycles of moisture fluctuation
… type of walls in expansive clay. Finally, the side shear and temperature effects on the lateral response of the wall were quantified. A differential linear thermal model was used to evaluate the temperature effects and a t-z analysis was conducted to account for the side shear applied on the …
-
The Use of Mini-Pile Anchors to Resist Uplift Forces in Lightweight Structures
… of mini-pile anchors. Mini-pile anchors generate side shear at the interface between the pile and the soil which resists the uplift forces.This thesis provides an overview of the design methods used to estimate wind-induced uplift forces and several foundation options used to withstand these …
-
Analysis of Statnamic Load Test Data Using a Load Shed Distribution Model
… complete results using a predictive model for side shear development with displacement during the statnamic test. A driven pile or drilled shaft can be discretized into segments based on the load shed distribution model. Each segment can be analyzed as a rigid body. The total static capacity is …
-
The Influence of Pile Shape and Pile Sleeves on Lateral Load Resistance
… more lateral resistance due to the increased side shear resistance, no test results have been available to substantiate the contention. Full-scale lateral load tests involving pile shapes such as circular, circular wrapped with high density polyethylene sheeting, square, H, and circular with a …
-
Effect of bioceramic fillers on antibiofilm and remineralization properties of flowable composite used as clear aligner attachments
… control group without fillers on the attachment side. Shear bond test was performed using a Universal Testing Machine. The shear bonding strength was not compromised in the attachments containing micro-fillers. In conclusion, proper incorporation of bioceramic micro-fillers in clear aligner …
-
An experimental study of the explosive welding window using a gas-gun
… the welds achieved, which were determined by a side shear test, are reported.<br/><br/>A welding window has been established within which welds of adequate integrity and without cracks can be obtained, although significant thinning of the flyer plate takes place in some regions of the window. …
-
Design of End Bent Piles for Downdrag
… relative to the pile, a downward-oriented side shear known as downdrag is introduced. While downdrag is addressed in current codes and textbooks, it is often only briefly mentioned and primarily in the context of clay soils, with little to no mention of sandy soils. Additionally, current …
-
SEISMIC DESIGN AND BEHAVIOUR OF PRECAST CONCRETE CONNECTIONS FOR ACCELERATED BRIDGE CONSTRUCTION
… spread footings. Test data from connection-level side shear load tests informed the development and validation of a finite-element model that accurately simulates capacity and damage modes under direct shear loading. Meanwhile, quasi-static cyclic tests at the pier component level demonstrated the …
-
Resistance analysis of axially loaded drilled shafts socketed in shale
… material at the test site, estimate the unit side shear and unit end bearing of the shale-shaft interaction by running two axial load tests, and compare the results to the current design methods that are used to predict the axial capacity of drilled shafts. A comprehensive field investigation, …
-
Development of a New Load Analysis Tool and a Unified p-y Method for Lateral Analysis of Large-Diameter Drilled Shafts Validated Using Load Tests
The drilled shaft foundation is often considered a reliable cost-effective solution in major engineering projects around the globe. The construction of a single drilled shaft can often replace several monopiles with smaller diameters while providing high load-bearing capacity and resistance to …
-
Influence of Pile Shape on Resistance to Lateral Loading
… sections was a result of increases in both the side shear and normal stress components of resistance. Using the back-calculated p-multipliers provided very good agreement between the measured and computed load-deflection curves and the bending moment versus depth curves.
-
Seismic performance of prefabricated bridge piers supported on pile foundations
… connection interfaces, demonstrating that side shear strength in the column socket connection is sufficient to transfer large vertical loads from the column to the pile cap. An outdoor test was subsequently conducted on the column-pile cap-pile system at a cohesive soil site. A half-scale …
-
Load and Resistance Factor Design (LRFD) Resistance Factors for Tip Grouted Drilled Shafts
Pressure grouting beneath the tip of drilled shafts, also known as postgrouting, has been used for more than fifty years throughout the world and has shown to be an effective means to enhance both the usable and ultimate end bearing resistance. In short, postgrouting is a form of compaction …
-
NEWLY MODIFIED GZZ CRITERION AND ITS APPLICATIONS
… stress on rock mass strength was stressed and considered in a 3D revision of the well-known Hoek-Brown (HB) criterion, and then the proposed 3D criterion was further developed as a constitutive model for rock mass and applied to various rock engineering practices.First, a 3D revision of the HB …
Page 1 of 2