Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 91 for “"soldered"”.
-
Dynamic response of soldered electronic components under impact loading
The objective of this research was to analyze the effects of impact loading on electronic component failure. A standard fiberglass composite printed circuit board (PCB) card was used in two impact tests. The first test consisted of a PCB card with four adhered strain gauges, which were mounted …
-
Analysis of Direct-Soldered Power Module / Heat Sink Thermal Interface for Electric Vehicle Applications
… other interface materials in between. However, a soldered interface typically contains a large number of voids, which results in local hot spots. This thesis describes approaches taken to reduce voids in the solder layer through surface treatment, solder paste selection, and adjustment in …
-
Comparison of relative deflection in a fixed partial prosthesis with a soldered joint and an semi-fixed partial prosthesis with a precision attachment under simulated occlusal forces
Precision and semi-precision attachments have been utilized in fixed partial prostheses for many years. A review of the dental literature reveals a lack of clinical and laboratory information and their use in specific situations therefore must have been empiricly established . The purpose of this …
-
Self assembled structures for 3D integration
… metal face. Mechanical grinding showed that face soldered SBSA structures were void free and robust in nature. In addition, the face soldered 3D structures provide a consistent heat resistant solder standoff height that serve as attachments in the integration of dissimilar electronic technologies. …
-
Effect of Processing Parameters and Thermal Cycling on the Microstructure and Strength of Eutectic Sn-Ag Solder on Cu
… solder joints were carried out on samples reflow soldered on copper substrate under various processing conditions. Light (LM) and scanning electron microscopy (SEM) as well as energy dispersive spectroscopy (EDS) were used to study the microstructural evolution, while microhardness and shear …
-
Evaluation of solder-joint reliability for a 10mm Quad Flat Leadless package with top-side paddle using classical models for a leadless device and accelerated life testing
… by moving the paddle to the topside. The soldered surface area of the package reduces by about 80% with a top-side paddle. The soldered-joint life will also reduce due to the significant thermal coefficient of expansion mismatch between the QFN package and the circuit board. The …
-
Comparative Tensile Strengths of Preceramic and Postceramic Solder Connectors Using High-Palladium Alloy
… Plus and Option (high-palladium) alloys on soldered connectors under simulated preceramic and postceramic soldering conditions. Materials and methods: Eighty cylindrical castings were fabricated (40 using Rx Naturelle Plus alloy and 40 using Option alloy). The 40 castings for each alloy were …
-
Impact of Board Pad Finish of the SnPb and Lead-free Solder Interconnect Reliability for Leadless Chip Resistors Under Random Vibration Loading
… terminal finish, tin and tin-lead, in tin-lead soldered assemblies are examined. The board pad finishes used in the assemblies tested included immersion tin, immersion silver, electroless or electrolytic nickel immersed in gold, and organic solderability preservative, while tin-lead hot air …
-
A Parametric Study Of Polarity, Contact And Current Risetime Effects On Wire Array Z-Pinches
… in both negative and positive polarity, with soldered and non-soldered contacts, and with slow and fast risetimes (100ns and 200ns). A minimum of five shots were collected for each of the eight cases to obtain statistical significance. The initiation, ablation, implosion and stagnation phases …
-
Galvanic Lead Corrosion in Potable Water: Mechanisms, Water Quality Impacts, and Practical Implications
… contacts copper pipe and lead solder (simulated soldered joints), a corrosion cell is formed between the metals in solder (Pb, Sn) and copper. If the resulting galvanic current exceeds about 2 µA/cm², a highly corrosive microenvironment can form at the solder surface, with pH <2.5 and chloride …
-
Fatigue Test for Determining the Isothermal Cyclic Stress-Strain Response of Solder Joints on a Circuit Board
… test boards with rectangular copper "components" soldered to them. The mismatch in the elastic moduli of the rectangular copper "component" and the fiberglass circuit board generate strains in the solder joints, when mechanically cycled, similar to the strains generated during thermal cycles and …
-
An Investigation of Filigree as Design in Selected Pieces of Jewelry
… an openwork technique in which wires were soldered together in a skeleton-like structure to form a tiara. The second problem concerned openwork filigree, a pendant, made of units soldered together. The third problem was executed in a hair pin which was a combination of open pierced work and …
-
Design of the Contact Metallizations for Gold-Tin Eutectic Solder-A Thermodynamic-Kinetic Analysis
… experimentally. The microstructures of the as-soldered and subsequently aged Au-20wt.%Sn|X interconnections were characterized by means of scanning electron microscopy equipped with energy-dispersive X-ray spectroscopy (EDX) and scanning transmission electron microscopy with EDX. The observed …
-
Leak rate prediction methods for hermetically sealed devices
… non-condensable gases. Experimental testing of soldered samples with seals like those in hermetically sealed devices confirmed that predictions using Graham's law could be inaccurate. Investigation of Graham's law showed that it may be derived from Knudsen's equation for molecular flow, which …
-
Rapid Prototyping of a Directly Heated Thermionic Triode Using 3D Printing Techniques
… and the grid and cathode filament supports were soldered to the remaining electrodes. The triode was characterized in a vacuum chamber to extract µ, its intrinsic gain, for several operating points when the grid was biased to 5 V. A maximum µ just below 25 was measured when the anode was biased …
-
FPGA-based digital phase-locked loop analysis and implementation
… this project involves several analog circuits soldered on PCBs, which will help the students visualize the signal flow in the PLL and get some exposure to mixed-signal systems.
-
Analysis of surface mount technology solder joints
… after soldering only one end of the component is soldered while the other is lifted up, assuming a position like a tombstone. The initiation of tombstoning during reflow was analysed based on the forces acting on the component. A model was developed to predict the initiation of this phenomenon. …
-
Mažatriukšmis stiprintuvas terahercinių dažnių detektoriams /
… prototyping machine “LPKF ProtoMat S63” and soldered.
-
PIN photodiode controlled class E microwave power amplifier
… manufactured in Sunstone Circuit Corporation, soldered and tested in the lab. The DC power is 0.5V and output is 0.4V (peak to peak sinusoidal waveform) at optimum performance in the lab. The optimum efficiency is 32% after calculation.
Page 1 of 5