Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 14 of 14 for “"spool valve"”.
-
Some flow characteristics of spool valve orifices
… jets issuing from effectively two-dimensional spool valve orifices. (Aspect ratio 2.5 - 45}. Reynolds number is varied from 200 to 3000 and cavitation number from 0.15 to 0.8.Valve geometry effects are examined by (a) varying the orifice opening and clearance and (b) by providing each valve …
-
EXPERIMENTAL CHARACTERIZATION OF SPOOL VALVE FLOW NOISE
… measure the flow noise produced by a spool valve and compare with measurements of orifice flow noise to reduce flow noise modelling complexity. The similarities and differences are compared over a range of volume flow rates, back pressures, and cross section areas. The impact of down …
-
CFD analysis of steady state flow reaction forces in a rim spool valve
Hydraulic spool valves are found in most hydraulic circuits in which flow is to be modulated. Therefore their dynamic performance is critical to the overall performance of the circuit. Fundamental to this performance is the presence of flow reaction forces which act on the spool. These forces can …
-
Quasi-Static Hydraulic Control Systems and Energy Savings Potential Using Independent Metering Four-Valve Assembly Configuration
In this research, the four valve independent metering configuration is to be investigated. The Independent metering concept will be emphasized and compared to spool valve coupled metering conventional technologies. Research focuses on the energy savings potential of the four valve independent …
-
Dynamic and efficiency characteristics of an inlet metering valve controlled fixed displacement pump
… (for variable displacement pumps) or bleed off valves (for fixed displacement pumps). Variable displacement pumps require mechanically complex parts which are expensive to machine and prone to break down. Bleed off valves represent a significant loss in system efficiency. In contrast, the inlet …
-
Hydraulic Variable Valve Timing Testing and Validation
… of a fully continuous, hydraulics-based variable valve timing system. This hydraulics based variable valve timing system is capable of controlling an engine valves lift height and infinitely varying the engine valves lift profile. Along with full valve controllability during normal operation, the …
-
Condition monitoring in a hydraulic system of an industrial machine using unscented Kalman filter
… the model are displacement and velocity of the spool valve, pressures of the two chambers of the hydraulic cylinder, and displacement and velocity of the hydraulic actuator. The unknown parameters of the state-space model are identified through direct measurement and experimentation. Results …
-
Estimating Parameters of a Proportional Solenoid Valve using Neural Networks
… in estimating on-line proportional solenoid valve parameters is the focus of this study. A neural network algorithm is well suited for this type of parameter estimation in that it is capable of learning and best fitting a solution to given data. It is also capable of handling inherent noise …
-
Modeling, simulation, and stability of a hydraulic load-sensing pump system with investigation of a hard nonlinearity in the pump displacement control system
… between the inlet and outlet of a flow control valve. With a constant margin pressure, predictable flow control and improved efficiency can be achieved by controlling the orifice area of the flow control valve. Instability due to limit cycles (sustained oscillations) that stem from …
-
Robust control design for a proportional valve with backlash compensation
… of a solenoid operated proportional control valve was performed using open loop testes. The model consists of linear and nonlinear parts. The linear part was developed by linearizing the nonlinear equations governing the operations of the valve at nominal conditions. The nonlinear parts …
-
Actuation and control for robotic physiotherapy
… cylinder prone to stiction effects and a single spool valve. Here the performance of modem pneumatic servo system, consisting of a low friction pneumatic cylinder and two electropneumatic proportional valves has been evaluated. The increased linearity of the modem pneumatic system enabled a …
-
CHARACTERIZATION OF HYDRAULIC FLOW NOISE INDUCED BY SPOOL VALVES
… investigate the relationship between operational valve parameters and flow noise generation. The primary consideration was correlating the flow noise generated by the valve with the distinct valve open positions. This data would allow future valve designs to account for features that cause …