Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 225 for “"stress values"”.
-
Comparing In Situ Submerged Jet Test Device and Laboratory Flume Methods to Estimate Erosional Properties of Cohesive Soils for Bank Stability Models
… to predict bank erosion: critical erosion shear stress and erodibility coefficient. The investigation’s purpose was to compare two erosion estimation methods and improve the bank stability models for cohesive soil commonly found on the banks.</p> <p>To accomplish the objective, critical shear …
-
Brain Tissue Mechanical Characterization and Determination of Brain Response under Confined Blasts Explosions
Mechanical experimental tests including stress relaxation, simple monotonic ramps, and impact loads were performed on porcine brain tissues to investigate the response of the brain under different loading scenarios. Linear viscoelastic models were employed to determine the applicability and …
-
Polymerization shrinkage stress of light curing dental composites
… To analyze the polymerization shrinkage stresses flowable and universal dental composites at different times. MATERIALS AND METHODS: Seven flowable and four universal composites; were used in this study. Two glass cylinders were fixed in a vertical position on the INSTRON machine; leaving …
-
Study of Mechanical Performance of Stent Implants Using Theoretical and Numerical Approach
… capture the deformation process. The maximum stress values were found to occur in localized regions of the stent. These regions were generally found along the inner radii of each of the connected links connecting each of the longitudinal struts. Stress values throughout the whole stent were …
-
A influência da adição de caulim, quartzo e feldspato potássico na formulação de massas cerâmicas para telhas: Modelo estatístico
… shrinkage, water absorption and bending rupture stress, by fitting the statistical model and using multiple linear regression to assess the relationship between technological properties and independent variables. The raw materials were characterized using the following techniques: X-ray …
-
Rheology and electro-acoustic characterization of laterite slurries
… in terms of the apparent viscosity and yield stress obtained through flow curve modeling. An attempt was made to correlate the results obtained for the laterite samples with data obtained for model single mineral systems as well as for model mixed mineral systems. In combination with detailed …
-
Efficacy of Vickers indentation method to measure residual stress in additively manufactured IN718 specimens
… parts for the aerospace industry. Residual stresses that remain in components after manufacturing are known to be detrimental, often resulting in geometric distortion and inadequate mechanical properties. It is therefore essential to be able to measure these residual stresses. Many …
-
Improvement of muscle protein functionality and evaluation of sodium reduction possibility by combining crust-freeze-air-chilling and cold-batter-mincing technologies
… the minced batter, higher cooking yield and stress values were found in HB-CFAC gels than in CB gels. In study II, two salt content levels (1.0% vs 2.0%) were compared. Higher protein extraction values were seen on 2.0% salt HB-1/4CFAC batters compared to 1.0% and 2.0% salt CB batters when …
-
Development of bimodal grain structures and their effect on toughness in HSLA steel
… fracture toughness by comparing local fracture stress values for uniformly fine, uniformly coarse and bimodal ferrite grain structures. Analysis of local fracture stress values suggests that bimodality can raise the scatter in the fracture test results and therefore, it is undesirable. Current …
-
Bond Strength of Mild Steel Reinforcement in High Strength Concrete
… study was conducted to determine the bond stress and slip between the high strength concrete and the reinforcement. Bond stress values were determined and compared to determine the effects of high strength concrete. Bond stress affects the development length of mild steel reinforcement. …
-
Pressure, temperature, and stress conditions of Southern Alpine Fault (New Zealand) mylonites
… 𝜇m in mylonitic quartz indicating differential stress values in the south of ~100 MPa, roughly twice the stress values observed in the central Alpine Fault. Constraints from Ti-in-quartz thermobarometry and Raman Spectroscopy of Carbonaceous Material (RSCM) indicate mylonitization occurred at …
-
Structure property behavior of an ethylene-propylene-diene ionic terpolymer containing zinc stearate
… a reinforcing filler under ambient conditions. Stress-strain behavior, percent relaxation, hysteresis and permanent set were all found to increase with increasing ZnSt content. Increases in stress values upon annealing for all samples were attributed to increased ionic domain formation and …
-
Tensile behavior of aluminum reinforced with angle-ply boron epoxy laminates
… was conducted. It is shown that the ultimate stresses of a wide variety of laminate configurations fall within a very narrow range of values. Some configurations of composite reinforced aluminum laminates exhibited higher ultimate stress values than the corresponding all composite laminates …
-
Timber Bridge Pile Splicing with Fiber Reinforced Polymer Wraps
… that were developed in this program. Theoretical stress values were compared with experimental stress values gained through laboratory testing to determine the reliability of the design equations. Shear and bending equations had low variability in theoretical versus experimental stress values. For …
-
A theoretical approach to the prediction of haemolysis in centrifugal blood pumps
… trauma which is primarily caused by hydrodynamic stresses. A general mechanical blood damage theory was developed which comprises a combination of the information about mechanical loading of blood with the knowledge of its resistance properties. In this theory arbitrary loading-time functions are …
-
Synthesis and characterization of LPCVD SiC films using novel precursors
… 850 C. The stoichiometric films exhibited high stress values of 700 +/- 50 MPa. Attempts to reduce the stress values resulted in films with excess carbon content of about 60%-C. From the high frequency C-V characterization, the dielectric constant for these films was estimated to be 10.1 +/- …
-
Influence of Progressive vs. Minimal Canal Preparations on the Fracture Resistance of Mandibular Molars: A Finite Element Analysis
… canal taper on residual tooth strength and stress distribution after root canal treatment. Methods: Two pre-accessed mandibular molar TruTeeth (Acadental Endo 3DP, Lenexa, KS) were subject to simulated endodontic treatment in this study. One tooth was instrumented with ProTaper Gold …
-
MATLAB script for slope stability calculations with COMSOL Multiphysics
… a factor of safety based on the finite element stress field calculated with COMSOL. The stresses are calculated based on a linear-elastic behaviour using a Young’s modulus and a Poisson’s ratio. The script is programmed to test a series of circular slip surfaces defined by their centre …
-
Damage Investigation in Dual-Phase 1000 Steel and Behaviour Prediction Using Microstructure Based Modelling
… thus allows further investigation for strain and stress values at the damage locations. The method was then used to investigate a crack initiation criterion in the martensite phase and predict crack propagation. A critical maximum principal stress value of 1700 MPa is suggested to initiate damage …
-
A finite element complementary energy formulation for plane elastoplastic stress analysis
… finite element model wherein the stress function is expressed by means of a complete set of quintic Hermitian polynomials. The function used, while allowing for selfequilibrating stresses that are continuous within the element, also enables the admission of all the second …
Page 1 of 12