Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 484 for “"substrate temperature"”.
-
Substrate temperature and carnation growth
… greenhouse benches in soil and in gravel. Soil temperatures were controlled at 7.2 to 10.0, 15.6 to 18.3, and 22.8 to 25.6°C. Gravel temperatures were controlled at 7.2 to 10.0 and 15.6 to 18.3°C. Some plots in both soil and gravel were left to fluctuate with the air temperature. Warming was …
-
Nanocrystalline Silicon Solar Cells Deposited via Pulsed PECVD at 150°C Substrate Temperature
… wave (cw) and pulsed (p)-PECVD at 150°C substrate temperature. Working at this temperature allows for the easy transfer of film recipes from glass to plastic substrates in the future. During the p-PECVD process the pulsing frequency was varied from 0.2 to 50 kHz at 50% duty cycle. …
-
The Effect of Ion Energy and Substrate Temperature on Deuterium Trapping in Tungsten
… was studied as a function of ion energy and substrate temperature. Deuterium retention was shown to decrease with decreasing ion energy below 100 eV/D+. Irradiation of tungsten specimens with 10 eV/D+ ions was shown to retain up to an order of magnitude less deuterium than irradiation with …
-
Chemical vapor deposition of polymeric films
… may allow deposition at a higher rate with lower substrate temperature. In this work the influence of deposition parameters, such as sublimation temperature, substrate (pyrolysis) temperature, pressure, plasma condition on the structure of deposition product was systematically studied. It's found …
-
Growth of obliquely deposited metallic thin films
… under highly oblique vapor incidence on planar substrates. Oblique angle deposition is a physical vapor deposition technique that is based on the self-shadowing effect. This enables the fabrication of highly porous thin films that are composed of three-dimensionally separated, micro-, and …
-
Surface diffusion: A computer study of its effects on thin film morphology.
… algorithm to the evaporation parameters of substrate temperature and evaporation rate. In the limit of no surface diffusion (low substrate temperature), the model predicts a dendritic structure with large voids; this is the Henderson model. With sufficient surface diffusion (higher substrate …
-
Growth and characterization of hydrogenated amorphous silicon prepared using a combined hot wire and electron cyclotron resonance plasma deposition technique
… in the same reactor using a 10.5 cm filament to substrate distance to minimize substrate heating by radiation during deposition. The growth rate is halved when ion bombardment is added to HWCVD, however it remains four times greater than the highest quality ECR-PECVD films. Also, ECR-HWCVD …
-
Electron beam-induced organometallic chemical vapor deposition for nanostructure fabrication
… of film growth has been conducted in the STEM. Substrate temperature and organometallic partial pressure play an important role in the growth mechanism. Two different film growth mechanisms and two resulting structures of the deposited material are found at different deposition conditions. The …
-
Laser annealing of Ni (001)
… for the thermally annealed surface. Effects of substrate temperature on laser annealing results are investigated. It is concluded that laser-annealing yields clean, well ordered surfaces for elevated substrate temperature, but not at room temperature.
-
An investigation of the temperature distribution induced during laser chemical vapor deposition (LCVD) of titanium nitride on titanium-aluminum-vanadium
To understand how the substrate temperature influences the deposition rate and spatial profile of deposits formed using laser chemical vapor deposition (LCVD), spatially resolved multi-wavelength pyrometry measurements of the substrate temperature have been made during LCVD of titanium nitride …
-
Plasma enhanced chemical vapour deposition of thin carbon films
… Their deposition rate was found to decrease with substrate temperature and increase with induced bias and pressure. The intrinsic stress and wear resistance were found to increase with the induced bias and substrate temperature but decreased as the pressure was increased. The film adhesion was …
-
Continuous high-speed resin 3D printing by interface temperature control : a thesis presented in partial fulfilment of the requirements for the degree of Master of Engineering in Mechatronics at Massey University, Albany, New Zealand. EMBARGOED until 15th December 2027
… by the stiction between the cured resin and the substrate. This stiction restricts how quickly layers can be separated during the printing process and is one of the key limitations preventing the wider adoption of high-speed and continuous 3D printing. This thesis investigates the impact of the …
-
Ferromagnetic resonance studies of DC magnetron sputtered CO-CR films
… of DC sputtered Co-Cr Films with different substrate temperatures. This angular variation has been Fitted with the classical uniaxial anisotropy crystal model and yields the values of 2K₁/M-4πM=-4∼-7 KOe, 4K₂ =-0.8∼0.8 KOe and g-factor = 2.3~2.8. The FMR measurments of the first anisotropy …
-
Observer-Based Simultaneous States and Parameters Estimation Method with Application to System Heath Monitoring
… Kalman filter is implemented to estimate the substrate temperature in the Advanced Metal Organic Chemical Vapor Deposition (AMOCVD) process, used for High-Temperature Superconductor tapes manufacturing. Precise temperature control in this process is crucial to minimize nano-scale defect growth …
-
Tailoring the properties of PECVD deposited terpinen-4ol thin films
… The effect of Process variables such as substrate temperature have been investigated on the PECVD of terpinen-4-ol. The influence of surface functionalization and the deposition mode of terpinen-4-ol plasma polymer on its antibacterial property has been studied. Coating created in the …
-
Development of a Sustainable Solution for the Elimination of Helium in the Copper Cold Spray Process for Used Nuclear Fuel Containers
… several copper powders and various steel substrate preparations, copper coating delamination still occurs. The purpose of the current study is to produce copper coatings using only nitrogen as the process gas, while avoiding delamination of the deposited material. To this end, the current …
-
Processing and characterization of Ge2Sb2Te5 and Sb2Te-based phase change memory films
… deposition (PLD) was studied. The effects of substrate temperature and laser energy density on the structure, surface and stoichiometry of the films were investigated to enhance the quality of the films by (i) reducing the size and number of the large particulates, (ii) decreasing the …
-
Characterizing growth conditions in chlorine-activated diamond chemical vapor deposition
… and experimental data. Modelling suggests a low substrate temperature diamond growth mechanism by atomic carbon insertion reactions. Such a mechanism becomes pronounced at high atomic hydrogen concentrations and can lower the apparent growth activation energy in the low substrate temperature …
-
CHARACTERIZATION OF ORGANIC GLASSES BY NEXAFS SPECTROSCOPY
… orientation by using electric field and substrate temperature during the film growth by PVD. Recently, PVD has been shown to produce organic glasses with enhanced kinetic and thermodynamic stability. For many organic glass formers, the substrate temperature during the deposition process …
-
SPH simulation of YSZ and stainless-steel droplet impact for thermal spray process
… alloys, and metallic) being propelled onto the substrate as molten or semi-molten droplets to form a dense coating. The quality of thermal sprayed coatings depends on the impact behavior of the droplets, which is, however, still not fully understood. In the present study, the Smoothed Particle …
Page 1 of 25