Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 30 for “"surface renewal"”.
-
A Comparison of Methods to Measure Crop Water Use in South Carolina
… humid climate. The methods analyzed were the surface renewal method (SR), the Eddy Covariance method (EC), large in-field weighing lysimeters, a newly developed pressure differential device (PDD), a Class A Evaporation pan, and the Penman-Monteith equation. In the first chapter, ET …
-
Gas absorption in cocurrent turbulent bubble flow
… results support a postulated mechanism of surface renewal by turbulent eddies which result from the mean flow of liquid through the tube. Two theoretical approaches have been described in an attempt to relate the surface renewal rate to the pipe flow turbulence. A model based on mixing …
-
Condensation induced water hammer
… fluid approach and condensation models based on surface renewal theory are used in the simulations. Different meshes and performance of the condensation models are investigated in the present work. The simulation results achieved are mesh independent and corresponded well with the experiment …
-
Decarburization of iron-carbon alloys with oxidising slags.
… Finally, the discussion suggests that Danckwerst surface renewal adaptation of the penetration theory is worthy of future examination.
-
Micrometeorological approaches to measure and model surface energy fluxes of irrigated citrus orchards in a semi-arid environment
… micrometeorological methods, mainly based on Surface Renewal theory, were studied and tested, in order to provide reliable and low cost estimates of sensible heat fluxes within the plant-atmosphere system. Micrometeorological techniques were integrated with in situ measurements of …
-
A Model for Condensation Heat Transfer in Hydrophobic-Hydrophilic Surfaces
… condensation on patterned-‐ hybrid surface. Establishing the model requires the modeling of fully dropwise condensation (DWC) before applying modifications to evaluate heat transfer performance of patterned-‐hybrid condensation surface. The model for fully DWC consists of defining …
-
Absorption in cocurrent gas liquid flow in horizontal tubes
… density, liquid-phase diffusivity, viscosity, surface tension, and tube diameter, on the mass transfer rates. The gas-liquid systems employed, in a single tube 1.757 cm. in diameter, were CO₂-water, He-water, CO₂-ethanol, and CO₂-ethylene glycol. Two additional tube sizes, 1.228 and 2.504.cm. …
-
Bubble Induced Heat Transfer in Two-Phase Systems
… has been extended to cover heat transfer at surfaces by introducing the concept of a property boundary layer in the vicinity of the surface. The property boundary layer is a consequence of changed voidage and hence of changed thermophysical properties of the emulsion phase at the surface. A …
-
Transcriptomic and ultrastructural responses to Amiodarone–Itraconazole in naturally benznidazole-resistant and -susceptible Trypanosoma cruzi strains
… of purine metabolism and inhibition of surface renewal pathways. In contrast, the MG strain showed 57 upregulated and 412 downregulated genes, including enhanced sphingolipid metabolism—potentially linked to membrane repair—and widespread suppression of energy and nucleotide biosynthesis …
-
Investigation of turbulence promoting inserts for augmenting heat transfer from gases in tubes
… mechanisms, were conducted;Finally, basic surface-renewal/penetration theory was utilized to describe, with reasonable accuracy, the trends in heat transfer enhancement in tubes augmented by this type of bent-strip insert.</p>
-
Investigating the Tribological Behaviours of a Jet Engine’s Abrasive Rotor and Stator Vane Contact
… incursion rate, ceramic material, abrasive surface finish, and coatings’ porosity have been identified as system variables, and a statistically planned test matrix has allowed to identify the significance and dependencies of each, along with building the required knowledge to optimise the …
-
Free Radical Processes in Plasma Functionalisation of Polyolefins in the Melt State
… treatments are commonly applied to polymer surfaces to increase surface energy by introducing polar functionalities. This work extends this approach to the melt phase, an area where its use has been comparatively limited. The thesis examines the radical reactions that arise when molten …
-
Laboratory assessment of diffusion across the gas-water interface within a bubble trap
… using the ideal gas law, Henry’s law, and the surface renewal model. Results showed that the bubble trap’s headspace can shrink or grow without ebullition, with these changes associated with gas diffusion across the gas-water interface driven by concentration differences. A control experiment …
-
Thermodynamics and kinetics of aqueous solution of liquid hydrocarbon mixtures (solutes, petroleum)
… did not change substantially in the process. A surface renewal mass transfer model is used to explain this result. The mass transfer model can also be used to help explain non-equilibrium solute concentrations resulting from water in contact with a hydrocarbon phase of changing composition due …
-
BTX extraction by sulfolane in a mixer-settler cascade
… greater, by a factor of 1.5 to 3, due to the surface renewal associated with drop break-up and coalescence promoted by agitation. A similar investigation was performed using real reformate from the Kuwait Oil Company. The phase ratios were in the range 0.5 to 1 to 3.25 to 1, the agitator speed …
-
Estimation of Field Alfalfa Evapotranspiration in a Windy, Arid Environment
… ET was estimated using eddy covariance (EC) and surface renewal (SR) techniques. ET estimates from the EC and SR analyses were compared with estimates using ASCE Standardized Reference ET Equation, with both dual and mean crop coefficients. EC energy balance closure was 0.80, on average, in 2009 …
-
In-line measurement of solibility of physical blowing agents in thermoplastic melts as related to extrusion foaming
… obtained from the in-line method. A simple surface renewal model is used to study the gas dissolution behavior over the gas injection section during the foaming process. The model was found insufficient to explain the very complex phenomena occurring inside the extruder, suggesting the …
-
Comprehensive Mathematical Model for Oxygen Steelmaking
… bulk zones, the velocity of flow of metal (or surface-renewal) at the interfaces of these zones are calculated by taking into the momentum induced by the top-jets and bottom-stirring plumes. This study found that these zones contribute negligibly to overall refining in the oxygen steelmaking …
Page 1 of 2