Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 51 for “"technology computer-aided design (TCAD)"”.
-
SILVACO MODELING AND SIMULATION OF THE MOS2 MEMTRANSISTOR
… will simulate an MoS2 memtransistor in Silvaco technology computer-aided design (TCAD). Subsequently, voltage sweeps will be applied to the simulated memtransistor to validate its accuracy against real-world prototypes developed by a research team at Pennsylvania State University. The benefits …
-
Transient Safe Operating Area (tsoa) For Esd Applications
A methodology to obtain design guidelines for gate oxide input pin protection and high voltage output pin protection in Electrostatic Discharge (ESD) time frame is developed through measurements and Technology Computer Aided Design (TCAD). A set of parameters based on transient measurements are …
-
MODELING SCHOTTKY BARRIER GAAS SOLAR CELL USING SILVACO ATLAS
… cost of cell fabrication. Using Silvaco ATLAS Technology Computer Aided Design (TCAD), we simulated and optimized the performance of back-side contact thin-film solar cells. In such a design, both anode and cathode contacts are placed on the same side of a device, resulting in no shadowing of …
-
Transient analysis of silicon carbide power MOSFET
… Power MOSFET. Transient analysis enables the designer to understand the thermal stress the semiconductor device undergoes while dissipating high power for short period of time. Silicon carbide has been a material of interest in the development of High Power Semiconductor device especially due …
-
Development and Characterization of 1200V and 1700V SiC Schottky Barrier Diode for Power Electronics Applications
… 1200V and 1700V SBDs are characterized and key design parameters like drift region length, active area, and carrier concentration are extracted. The device design process is explored and edge termination structures like junction termination extension (JTE) and floating field ring (FFR) are …
-
Modeling and Analysis of Quantum Well Structures in GaNInGaN Light Emitting Diodes
… be prohibitive to full exploration of potential design spaces. Technology Computer Aided Design (TCAD) simulation tools have emerged allowing engineers to explore design alternatives at an early stage. However simulations, especially for new materials and devices exhibiting quantum effects, must …
-
Defect Modeling and Device Optimization in Chalcogenide Photovoltaics from First Principles to AI-assisted Design
… optimization. The developed predictive Technology Computer Aided Design (TCAD) model offers a detailed depiction of defect behaviors and their impact on device performance, serving as a powerful tool for guiding experimental efforts and advancing the development of high-efficiency …
-
NEUTRON IRRADIATION EFFECTS AND APPLICATION OF JUNCTION TERMINATION EXTENSION ON GAN SCHOTTKY DIODES
… power devices against neutrons was examined via technology computer-aided design (TCAD) models in two steps. First, the forward bias characteristics of experimental bulk GaN Schottky barrier diodes (SBD) utilizing Rhenium (Re) as the Schottky contacts were simulated after fast neutron (1 MeV) …
-
Effects of Collector Profile on the Single-Event-Transient Response of High-Speed and High-Breakdown Silicon-Germanium Heterojunction Bipolar Transistors
… bipolar transistor (SiGe HBT) variants designed for high-speed (HS) applications and high-breakdown (HB) applications is presented. A significantly lower amplitude SET response at low laser pulse energies was observed in the HS device compared to the HB device. At high laser pulse …
-
Radiation Damage in CMOS Image Sensors for Space Applications
… Coupled Device (CCD) style CMOS image sensor designed for TDI (Time Delay and Integration) mode imaging, a mode commonly used for Earth observation. Damage from high energy protons in the space environment decreases the Charge Transfer Efficiency (CTE) and increases the dark current of such …
-
A low-cost laser grooved interdigitated back contact solar cell
… devices have yet to become the market leading technology due to the costly and tricky fabrication processes required to keep the doped regions of the p/n junction separate from each other whilst being on the same side of the wafer. This project will demonstrate a novel approach using lasers to …
-
Area Efficient Device Optimization for ESD Protection in High Speed Interface ICs
… for improving the circuit performance. These design challenges could be easily overcome if the parasitic components in a circuit were used for ESD protection. Despite the various design challenges, on-chip ESD protection is still desirable as it saves the area on the circuit board by …
-
Nanoscale thin film transistor design and device physics
… This dissertation first investigates the design and device physics of nanoscale TFTs through a combined experimental and physics-based modeling approach. Amorphous InGaZnO (a-IGZO) TFTs employing nanospike source and drain electrodes are fabricated to enhance gate control over channel and …
-
Nanoscale RF CMOS transceiver design
… provides guidelines for low-power (LP) RFIC design, focusing on low-noise amplifier (LNA) design, by implementing, measuring, characterizing, and modeling a 90 nm CMOS LP process, from DC to RF. De-embedding is applied to RF and noise measurements in order to remove parasitics inserted from …
-
Characterization of two-dimensional electrostatic potential profiles in deep submicron MOSFET devices
… and solving problems in semiconductor device technology. This dissertation describes the application of electron holography to dopant distributions in deep submicron devices and compares the outcome with results obtained by other techniques. For this study, complementary metal oxide (CMOS) …
-
Design, scaling and reliability of devices for high-performance mixed-signal applications
… heterojunction bipolar transistor (HBT) device design couples with both performance scaling and reliability for mixed-signal applications (high-frequency and analog). In addition, this work provides methods of using this knowledge to enhance the predictive modeling of performance and reliability …
-
Combined accumulation-depletion-mode SiMOS quantum dots for quantum computation
… unintentional quantum dots. Multi-layer device designs can also increase the probability of failure during fabrication. In order to address the issues mentioned above, a new device design was proposed, which replaces the overlapping regions by patterning the top gate and the barrier gates side …
-
Technology computer aided design and analysis of novel logic and memory devices
… analyzed. For the latter purpose the commercial technology computer aided design (TCAD) simulators Taurus and Sentaurus Device by Synopsys are used. These simulators allow ready definition of complex device geometries. Moreover, while not all device physics models are state-of-the-art, the wide …
-
Study of Defect-Enhanced Charge Multiplication in an Irradiated Avalanche Photodiode
… irradiation. Simulating the IBIC pulse with technology computer-aided design (TCAD) software revealed that introducing negative defects could lead to DECM. The localized distortion of the internal electric field led to increased rates of impact ionization and ultimately increased the total …
-
ESD-robust 4H-SiC Low-voltage CMOS Technology Development for High Temperature
… discharge (ESD)-robust, low-voltage CMOS technology using 4H-silicon carbide (SiC) tailored for high-temperature applications, addressing the critical need for reliable semiconductor devices in harsh environmental conditions. The advent of SiC as a semiconductor material offers significant …
Page 1 of 3