Global ETD Search

Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.

Results

Showing 1 to 20 of 59 for “"tension testing"”.

  1. Diagonal Tension Testing of Interlocking Compressed Earth Block Panels

    This thesis examines the use of diagonal tension (shear) testing to determine factors affecting shear strength of Interlocking Compressed Earth Block (ICEB) panels. This work expands on the current information available about strength properties of ICEB assemblies, which are dry-stacked, as opposed …

    calpoly Repository record for Diagonal Tension Testing of Interlocking Compressed Earth Block Panels (opens in a new tab)

  2. Application of Direct Tension Testing to Field Samples to Investigate the Effects of HMA Aging

    … The lack of an effective and efficient method of testing field samples has contributed to this deficiency. This study focused on the development of a method for preparing and testing field samples in direct tension. This methodology was then be employed in combination with the VEC and RDT* tests …

    tamu Repository record for Application of Direct Tension Testing to Field Samples to Investigate the Effects of HMA Aging (opens in a new tab)

  3. Application of Direct Tension Testing to Laboratory Samples to Investigate the Effects of Hot Mix Asphalt Aging

    … compacted (LMLC) samples. Direct tension tests were conducted on HMA samples to measure mixture stiffness and a Modified Calibrated Mechanistic with Surface Energy (CMSE*) analysis method was used to predict fatigue life. The effect of various mix design parameters was evaluated to …

    tamu Repository record for Application of Direct Tension Testing to Laboratory Samples to Investigate the Effects of Hot Mix Asphalt Aging (opens in a new tab)

  4. Numerical and experimental studies on the use of a Split Hopkinson Pressure Bar for high strain rate tension testing

    … generation limit the broader application of the testing technique. The current investigation addresses tensile load generation in a tensile SHPB apparatus, establishes a reliable loading methodology, develops a correction methodology for one dimensional theory strain estimation, and identifies …

    wichita-thes Repository record for Numerical and experimental studies on the use of a Split Hopkinson Pressure Bar for high strain rate tension testing (opens in a new tab)

  5. The effect of thermomechanical processing variables on ductility of a high-Mg, Al-Mg-Zr alloy.

    … from one to fourteen percent elongation in tension testing. This variability in ductility was studied in a series of experiments conducted jn an Al-10%Mg-0 . l%Zr alloy. Study by light microscopy and scanning Electron microscopy revealed defects resulting from inverse segregation in the …

    nps Repository record for The effect of thermomechanical processing variables on ductility of a high-Mg, Al-Mg-Zr alloy. (opens in a new tab)

  6. Development of lunar ceramic composites, testing and constitutive modeling, including cemented sand

    … involves new molding methods, development of tension testing setup, uniaxial compression and tension testing of ICC. Results showed that strength and ductility can be improved significantly by applying fibers. The second portion of the study proposes a unified constitutive modelling approach …

    arizona-thes Repository record for Development of lunar ceramic composites, testing and constitutive modeling, including cemented sand (opens in a new tab)

  7. The Effect of Loading Conditions and Specimen Size on the Tensile Strength of Ring-Shaped Specimens

    This study introduces a custom-built direct tension testing apparatus designed for ring-shaped rock specimens. The apparatus applies a uniform axial load to the inner surface of the ring and is compatible with standard geotechnical testing equipment. Using this device, 176 granite specimens sourced …

    boise Repository record for The Effect of Loading Conditions and Specimen Size on the Tensile Strength of Ring-Shaped Specimens (opens in a new tab)

  8. Effect of strain and strain rate on the microstructure of a superplastically deformed Al-10%Mg-0.1%Zr alloy.

    … warm rolling at 300°C to 90-95% reduction. Tension testing was done at various temperatures and strain rates and superplastic elongations were observed for both alloys. Subsequently, samples of Al-1 0%Mg-0. 1 %Zr were tested at 300°C to strains ranging from 8% to 267% as well as to fracture. …

    nps Repository record for Effect of strain and strain rate on the microstructure of a superplastically deformed Al-10%Mg-0.1%Zr alloy. (opens in a new tab)

  9. A preliminary investigation of the corrosion and stress-corrosion susceptibility of thermomechanically processed high magnesium aluminum magnesium alloys

    … 7076-T6. Results obtained from stress-corrosion testing and from tension testing after stress-corrosion exposure indicate that these 8-10% Mg alloys are less susceptible to stress corrosion cracking than 7076-T6. the addition of Cu or CU and Mn to a 10% Mg alloy raises strength, homogenizes the …

    nps Repository record for A preliminary investigation of the corrosion and stress-corrosion susceptibility of thermomechanically processed high magnesium aluminum magnesium alloys (opens in a new tab)

  10. Cyclic Loading of Porcine Coronary Arteries

    … arterial soft tissue collected from cyclic tension testing. Coronary arteries from porcine hearts will be tested as a material that closely models the plaque cap in non-linear elastic behavior. The S-N curve will be developed through failure testing with multiple cycles at stresses between …

    gatech Repository record for Cyclic Loading of Porcine Coronary Arteries (opens in a new tab)

  11. Superplasiticity in thermomechanically processed high magnesium aluminum-magnesium alloys

    … deformation characteristics of these alloys. Tension testing was conducted at strain rates ranging from 5.3x10(-5) to 5.3/10(-2) s-1 and temperatures varying from ambient to 300 degrees C. Materials in the warm rolled condition exhibited the highest strength at ambient temperature and were …

    nps Repository record for Superplasiticity in thermomechanically processed high magnesium aluminum-magnesium alloys (opens in a new tab)

  12. Characterization of VLSI interconnect materials: Mechanical behavior, time-dependent plasticity, and electromigration

    … A Hall-Petch relationship determined for bulge testing of pure aluminum is comparable to another worker's results for films tested by the substrate curvature method. Al-Cu(2%) alloys are shown to have a response to precipitation hardening similar to that of bulk material of the same composition. …

    rice Repository record for Characterization of VLSI interconnect materials: Mechanical behavior, time-dependent plasticity, and electromigration (opens in a new tab)

  13. Computational Stress and Deformation Analysis of Mammary Prosthesis

    … the breast implants was developed through axial tension testing, while linear and non-linear breast tissue models were assumed based on smooth muscle. These material models were to develop axisymmetric finite element models to determine the stresses in the implant walls under tissue loading. The …

    vt Repository record for Computational Stress and Deformation Analysis of Mammary Prosthesis (opens in a new tab)

  14. The Comparison of the Tensile, Shear-Peel, and Torque Orthodontic Bond Strength Test Methods Performed on a Resin and Two Glass Ionomer Cements

    … tensile, shear-peel, and torque bond strength testing methods using a commercially available resin (R), light-cured (LC), and chemically cured (CC) glass ionomer. Sixty-three bovine incisors were randomly divided into three groups. Stainless steel incisor brackets were bonded to the prepared …

    iupui Repository record for The Comparison of the Tensile, Shear-Peel, and Torque Orthodontic Bond Strength Test Methods Performed on a Resin and Two Glass Ionomer Cements (opens in a new tab)

  15. The effect of thermomechanical processing on the tensile properties and microstructure of a 6061 Al-Al_x001B_b2_x001B_s0_x001B_b3_x001B_s metal matrix composite

    … during subsequent straining. Failure during tension testing resulted from the ductile tearing of the matrix as voids initiated by the cracking of reinforcement particles, joined together. A distinct microstructural difference related to processing history was the development of a strongly …

    nps Repository record for The effect of thermomechanical processing on the tensile properties and microstructure of a 6061 Al-Al_x001B_b2_x001B_s0_x001B_b3_x001B_s metal matrix composite (opens in a new tab)

  16. An evaluation of a silicon carbide/alumina ceramic composite for use in high temperature air heaters

    … in properties. The project included mechanical testing and microscopy. The mechanical testing consisted of compression and tension testing of circular rings of unexposed and exposed material. The microscopy included stereo, metallurgical, and scanning electron microscopy as well as microprobe …

    ut-knoxville Repository record for An evaluation of a silicon carbide/alumina ceramic composite for use in high temperature air heaters (opens in a new tab)

  17. Bauschinger effect in Nb and V microalloyed line pipe steels

    … effect was measured during compression-tension testing for the same steel conditions. The yield stress drop during reverse deformation has been found to increase with an increase in forward pre-strain, dislocation density and particle number density within the effective particle diameter …

    birmingham Download PDF for Bauschinger effect in Nb and V microalloyed line pipe steels (opens in a new tab)

  18. Friction stir processing of AS-CAST AA5083 Superplastic response

    … were prepared by wire EDM for high-temperature tension testing. Tensile tests were carried out at 450 degrees C under different strain rates. The relationship between strain rate and elongation was established. A maximum superplastic elongation of ~550% was obtained at a strain rate of 3 x 10-3 …

    nps Repository record for Friction stir processing of AS-CAST AA5083 Superplastic response (opens in a new tab)

  19. Damage Analysis of Aluminum Structure Repaired with A Composite Patch

    … composite patch repaired structures. The compact tension testing of aluminum, four-point bend and fracture testing of composite repaired structures are employed to investigate the yielding and cracking in aluminum, fiber breakage, matrix cracking and delamination in the composite patch, and …

    utk-theses Repository record for Damage Analysis of Aluminum Structure Repaired with A Composite Patch (opens in a new tab)

Page 1 of 3