Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 139 for “"transformation temperature"”.
-
Development of low transformation temperature welding (LTTW) consumables, The
Includes bibliographical references (pages 149-156).
-
Effects of composition upon the martensite transformation temperature of austenitic steel welds
Includes bibliographical references (pages 143-151).
-
Welding simulation of steels welded with low transformation temperature (LTT) filler materials
… of thermal expansion, plastic flow and phase transformation. By using filler material which has a composition that transforms to phase transformation to Martensite at low temperatures, the residual stress state can become more favorable. The purpose of this thesis is to develop a numerical …
-
Effect of transformation temperature on the effective grain size and crystallographic orientation of bainitic ferrite
Includes bibliographical references (pages 125-131).
-
Analysis of low transformation temperature welding (LTTW) consumables: distortion control and evolution of residual stresses
… and after the weld is cooled to room temperature. They result due to thermal contraction that occurs during cooling. These tensile residual stresses also give rise to distortion. The deleterious tensile residual stresses in the weld toe region reduce the fatigue life of weld …
-
Stability and optimization of p-Phase precipitates in nickel-titanium-palladium shape memory alloys
… for this research is the understanding of phase transformations that lead to an increase in the shape memory effect (SME) transformation temperature in a Ni-Ti-Pd shape memory alloy (SMA). The research addressed three major parts of this transformation - (1) The phase stability of the P-phase …
-
Magnetic Field Induced Strain in Polycrystalline Magnetic Shape Memory Foam
… of polycrystalline Ni-Mn-Ga foam include phase transformation temperature, pore architecture, spatial distribution of pores, porosity, training, and magnetic anisotropy/texture. Samples were tested for MFIS and phase transformation temperatures to probe for a correlation. Single pore foam …
-
Characterization of Mechanical and Magnetic Properties of Ni-Mn-Ga Shape Memory Thin Films Deposited onto Silicon and Alumina Substrates
… performed to characterize the martensitic phase transformation temperature, the in-plane film stress change during the phase transformation, and the biaxial modulus of each film. Vibrating sample magnetometry was performed to characterize the Curie temperature and the magnetic anisotropy of each …
-
Characterization of the structure and substructure of thermally transformation cycled Cu-Zn-Al shape memory alloys
… the parent and martensite phases. The trends of transformation temperature versus number of cycles were correlated with observed microstructure . Specimens were examined through transmission electron microscopy techniques. The character of lattice defects and residual structures in the parent …
-
Flux Growth of Single Crystal Lead-Titanate and Property Measurements
… Of particular concern is the disruptive phase transformation at approximately 500$\sp\circ$C, and the attainment of large equidimensional crystals free of defects. A flux method was developed for the growth of single crystals at reduced temperatures. High quality crack-free crystals were …
-
Superplasticity and creep behaviour in pure zirconia
… using a creep-in-bending method with programmed temperature increase, showed the occurrence of superplasticity at temperatures near the monoclinic to tetragonal phase transformation. An interesting phenomenon was observed in a temporary halt to the creep process which occurred with continuing …
-
Austenite decomposition during hot strip rolling of microalloyed low carbon steel
… to 100℃/s), and retained strain (0.2, 0.4) on transformation kinetics and the transformation products under no-recrystallized rolling conditions were examined. With contact dilation measurements on a series of continuous cooling tests, transformation temperature was found to increase with …
-
Mechanical and caloric response of BaTiO3 and BaTiO3 reinforced metal matrix composites
… near the paraelastic to ferroelastic phase transformation temperature changes significantly, and this phenomenon and phase transformation temperature are stress and frequency dependent. While previous reports of metal matrix composites incorporating barium titanate particles report anomalous …
-
The generation of thermal stress and strain during quenching.
… The effect of an applied stress during transformation (transformation plasticity) was also introduced in the mathematical model. The new model produced a marked improvement in the degree of agreement between the calculated and experimental residual stress, although the corresponding …
-
Microstructure and continuous cooling transformation behaviour of C-Mn-Ni and C-Mn-Ni-Mo weld metals
… were produced which revealed that the γ-α transformation behaviour of the weld metals was controlled by the cooling rate, type and content of the alloying element, prior austenite grain size and the oxygen content. It was shown that progressive addition of nickel depresses the …
-
Influence of microstructure on the shape memory properties of two Ti-lean, Ni-Ti-Pt high temperature shape memory alloys
… of choice for development of derivative high-temperature shape memory alloys (HTSMAs). Ternary additions of Hf, Zr, Pt, Pd, and Au can be made, in quantities greater than [approximate] 10 at.%, to increase the transformation temperature of Ni-Ti based SMAs. Pt as an alloying addition is …
-
Influence of Inelastic Phenomena on the Actuation Characteristics of High Temperature Shape Memory Alloys
Most e orts on High Temperature Shape Memory Alloys (HTSMAs), have focused on improving their work characteristics by thermomechanical treatment methods. However, the in uence of transformation induced plasticity (TRIP) and viscoplasticity during actuation has not been studied. The objective of …
-
Development of laser powder bed fusion and heat treatment parameters for additively manufactured Ni51.5Ti48.5 shape memory alloys, The
… been shown to produce dramatic composition and transformation temperature changes. These characteristics, combined with the capability to produce complex geometries, provide a platform for transforming the design process for materials utilized in the medical and aerospace industries. To date, …
Page 1 of 7