Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 28 for “"weak-axis"”.
-
WEAK AXIS BENDING RESPONSE OF POLYGONAL HOLLOW STEEL SECTIONS
… and rectangular hollow sections (RHS) under weak-axis four-point loading, and the second section focuses on the complementary structural evaluation of PHS and RHS beams via distributed fiber optic strain sensors (DFOS). The moment capacity of the RHS tested were determined to be higher than …
-
Strength and Stiffness of Weak-Axis Moment End-Plate Connections
… to investigate the strength and stiffness of weak-axis moment end-plate connections. Each test consisted of two girders connected to a column web with four-bolt extended moment end-plates. Two tests were conducted with bare steel. One test included a composite concrete slab that confined the …
-
Evaluation and modeling of the performance of glulam under weak-axis bending
… construction sector. This study investigates the weak-axis bending performance of glulam to address the overly conservative design assumptions in the Canadian Code of Engineering. The current CSA O86 design standard assigns a conservatively low specified bending strength of 11.0 MPa for Hem-Fir …
-
Elastic And Inelastic Stability Of Two-Panel Tiered Concentrically Braced Frames
… that differential tier drifts resulting in weak-axis flexural yielding have on the strong-axis buckling strength of columns in a four-tier concentrically braced frame. A three-dimensional finite element analysis was used to impart varying levels of weak-axis flexural yielding onto various …
-
Structural Benefits of Hempcrete Infill in Timber Stud Walls
… density hempcrete (715 kg/m3) not only prevented weak axis buckling of columns but also carried some direct load. Low density hempcrete was also successful in preventing weak axis buckling of the infilled walls. In-filled walls failed in strong axis buckling at a load twice (for half scale walls …
-
Strengthening Slender S-Section Steel Columns Using CFRP Plates of Various Moduli
… to the column flanges when buckling about the weak axis. Twelve columns, with a slenderness ratio of 197, were tested, of which nine were strengthened with CFRP. The main parameters tested were the level of initial out-of-straightness (length (L)/8387 to L/1020), CFRP modulus (168 to 430 GPa), …
-
Lifting Analysis of Precast Prestressed Concrete Beams
… the beam, the internal forces and moments, the weak-axis and strong-axis deflections, and the cross-sectional angle of twist. Finite element simulations are performed to investigate the behavior of concrete beams during lifting and to validate the proposed method. Additionally, a statistical …
-
Design, construction, and analysis of a modular structural model for shake tables
… alignment, with a focus on the first five weak-axis modes as well as the primary torsional and strong-axis modes. The comparisons confirmed close agreement in the weak direction, demonstrating the model’s usefulness for future studies in dynamic analysis and structural model calibration.
-
Modeling of Integral Abutment Bridges Considering Soil-Structure Interaction Effects
… The abutments, which are supported on piles in weak-axis bending move into and away from the backfill soils when the bridge deck undergoes thermal loading. These bridges provide numerous advantages to traditional bridges including reduced maintenance, simpler bridge hardware, and better …
-
Finite-element modelling of 3D timber structures Efficient pre- and postprocessing modelling strategies for 3D timber shear walls
… foundation or floor as well as considering the weak axis strength of shear and tension connectors. Further a discussion is held concerning modelling strategies suitable for linear dynamic analysis and recommendations are made to take precautions of how the non-linearities in the model are …
-
Development of performance sections for cold-formed steel residential construction
… Specified Lateral Load Tables</i>, the <i>Strong Axis Axial Load Capacity Charts</i>, and the <i>Weak Axis and Torsional Axial Load Capacity Charts</i> were developed. The typical design aids for roof/floor joists include the <i>Uniform Load Capacity Tables</i> for single and two continuous spans, …
-
Stability Analysis of Single and Double Steel Girders during Construction
… to wind load. The analyses focus on the weak axis bending of the double girder system as a whole and an evaluation of whether buckling of cross-bracing is an issue when lateral loads are present.</p>
-
Behavior of structural clay tile infilled steel frames subjected to in-plane loading
… had W10 x 30 wide flange columns bent about the weak axis and a W12 x 35 beam. Eight inch by twelve inch by twelve inch structural clay tile masonry was placed into the frames using Type N mortar. The tile was placed with the cells horizontal using full bed joints and face shell bedding in the …
-
System-level seismic performance of steel gravity framing
… differences, especially for cases with weak axis decking or strong axis decking with a seam. These large differences are attributed to a significant separation of the girder from the column in the subassembly testing setup, which may not be present in a real building. The data generated …
-
Expanding the length of jointless bridges by providing rotational capacity over the pile head
… connection. Further, it is shown that strong axis bending results in more displacement capacity as compared to weak axis bending, although the lateral stiffness would be smaller in the latter case. Experimental study has been carried out on the proposed connection of CFT piles to the concrete …
-
Rectangular Hollow Sections Subject to Blast Loading
… torsional characteristics and square RHS have no weak axis in flexure, all ideal properties for response to blast loading. RHS have the added benefit of enabling the use of concrete-filling to create composite members which take advantage of the added mass and local stability provided by the …
-
Field Monitoring and Evaluation of Curved Girder Bridges with Integral Abutments
… accurately predicting the relationship between weak axis bending strain in the piles and the pile head displacement; the measured internal stress in the abutment piles due to expansion and contraction of the bridge were generally below 50% of yield stress; and the soil pressures on the abutment …
-
Soil–Structure Interaction of Curved–Integral–Abutment Bridges
… the pile–abutment connection is in the order of weak axis H piles, pipe piles, and strong axis H piles.
-
Innovative studies on reinforced concrete panel structures through experimental testing and finite element modeling; and teaching structural engineering courses using augmented reality
… wall damper system, are testing for their axial, weak-axis bending, strong-axis bending, and shear strengths. Results of testing are compared to walls of the same geometry without openings, as well as developed finite element models. Results indicate that as expected, walls with openings do …
Page 1 of 2