Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 62 for “"weld joint"”.
-
Dissimilar Metal Friction Stir Welding of Aluminum to Magnesium Alloys
… aluminum (Al) to magnesium (Mg) by friction stir welding resulted in the intermetallic formation inside the stir zone under all conditions of welding. The presence of brittle and low toughness intermetallic phases results in low strength and ductility of the weld joint. The strength of 6063 Al and …
-
WELD PENETRATION IDENTIFICATION BASED ON CONVOLUTIONAL NEURAL NETWORK
Weld joint penetration determination is the key factor in welding process control area. Not only has it directly affected the weld joint mechanical properties, like fatigue for example. It also requires much of human intelligence, which either complex modeling or rich of welding experience. …
-
Mechaninių ir deformavimo diagramos charakteristikų priklausomybių nustatymas būdingame intervale /
… master thesis alloy structural steels and their weld joint materials cyclic stress–stain curves parameters A1, α, sT dependences on mechanical characteristic in the typical range at room and elevated temperatures are determined. Consistent statistical analysis of experimental results shown, that …
-
Evaluation of sensitization in stainless steel 304 and 304L using nonlinear Rayleigh waves
… process in the heat affected zone of a weld joint. The results show a dependency of the nonlinearity parameter to the distance from the weld joint.
-
Ultrasonic Attenuation In As-Deposited Inconel 182 Weld Metal and Recommended Techniques for Discontinuity Evaluation.
… the ultrasonic evaluation of full penetration welds in pressure retaining bi-metallic and tri-metallic joints involving as-deposited austenitic weld material. The weld joint design was one simulating a component on a nuclear reactor known as a safe-end-to-nozzle. Because the joint is part of a …
-
Further Investigations on the Weldability of Titanium Molybdenum Alloy Archwires
… an extension of Dr. Lin's thesis research on the welding of Titanium Molybdenum Alloy (TMA) archwires. The flat-to-flat electrode configuration was utilized in an attempt to find optimum weld joints, with a minimum of distortion, while maintaining strength and ductility. Joint strength …
-
Efeitos dos tratamentos térmicos pós-reparo por soldagem na microestrutura e na dureza de superliga 718 em fundidos e forjados
… parts. Such components are typically repaired by welding followed by solution and age heat treatments. However, there’s a tendency of degradation of the material’s microstructure due to the repetitive thermal cycles which are performed below δ phase solution temperature. Therefore, this work’s …
-
Design of an experiment to investigate submerged arc welding variables
… To present a discussion of known submerged arc welding variables and their general affect on weld bead appearance 2. To design an experiment to investigate the affect on weld joint strength and hardness distribution across the weldment by using (1) Four different welding currents (450, 500, 550, …
-
The Viability of using a Gleeble for Physical Simulation of High Frequency Induction Welded TRIP 690 AHSS
High Frequency Induction Welding (HFIW) is the predominant process for high volume production of small diameter tubes and pipes for hydroformed automotive and oil and gas applications. This process is well-established due to its high throughput and continuous nature which makes it ideal for …
-
Stress corrosion cracking and hydrogen embrittlement of thick section high strength low alloy steel.
… to evaluate the corrosion performance of weldments of a high strength low alloy(HSLA) steel in a simulated seawater environment. This steel, designated HSLA80, was developed by the United States Navy for use in ship structural applications. Stress corrosion CRACKING(SCC) and hydrogen …
-
Dissimilar Joining of Al (AA2139) – Mg (WE43) Alloys Using Friction Stir Welding
… research demonstrates the use of friction stir welding (FSW) to join dissimilar (Al-Mg) metal alloys. The main challenges in joining different, dissimilar metal alloys is the formation of brittle intermetallic compounds (IMCs) in the stir zone affecting mechanical properties of joint …
-
An X-Ray Diffraction Study of Shearing Stresses in Aluminum Rods
… strain at a singular point, say the corner of a weld joint, must be determined by extrapolation. Men have long sought for a method to eliminate these undesirable shortcomings mentioned above. One of the purposes of this thesis is to acquaint the reader with a general knowledge of the use of X-ray …
-
TOWARD INTELLIGENT WELDING BY BUILDING ITS DIGITAL TWIN
… for the physical entities. This work takes welding manufacturing as the case study to accelerate its transition to intelligent welding by building its digital twin and contributes to digital twin in the following two aspects (1) increasing the information analysis and reasoning ability by …
-
Welding of cast A359/SiC/10p metal matrix composites
Welding of metal matrix composites (MMCs) is an alternative to their mechanical joining, since they are difficult to machine. Published literature in fusion welding of similar composites shows metallurgical problems. This study investigates the weldability of A359/SiC/10p aluminum SiC MMC. …
-
Influência do hidrogênio na tenacidade à fratura de junta soldada de aço 9% níquel
… to study the fracture toughness of 9%Ni steel joints welding by GTAW in the root and GMAW in the filling using 625 nickel alloy as weld metal. It was performed CTOD and J- integral tests in the base metal, in the welded joint and in the coarse grains of the Heat Affected Zone (CGHAZ), in the …
-
Optimisation of GMAW via the alternating shielding gas technique
… the alternating shielding gas technique in arc welding systems has been previously studied due to advantages such as greater penetration of the weld joint, refined microstructure of the fusion zone, reduced heat input, and increased travel speeds of the welding torch. Yet, relatively little work …
-
Finite element modeling of arc welded joint based on the experimental studies of the weldment
The structural integrity of a welded structure depends mainly on the performance of the welded joints. Due to the welding process, the mechanical properties of the structure change and different regions are created in the weldment. The mechanical properties of welded joints change significantly …
-
A superconducting RF deflecting cavity for the ARIEL e-linac separator
… from bulk, low purity niobium and the use of TIG welding for joining the cavity parts. A method for TIG welding niobium is developed that achieves minimal degradation in purity of the weld joint while using widely available fabrication equipment. Applying these methods to the fabrication of the …
-
Finite element modeling of welded joint using effective notch stress approach
Automotive structures contain hundreds of welds. Most of the time, failure occurs at the weld ends (weld toe or weld root). Thus, welds affect the structural integrity of an entire structure. Thus, the modeling of welded joints is very important from a design point of view. In this research, the …
Page 1 of 4