Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 52 for “"wet etch"”.
-
Fabrication of silicon nanowires with controlled nano-scale shapes using wet anisotropic etching
… functional device layers requires anisotropic etch techniques. Dry reactive ion etch techniques are commonly used since most solution-based wet etch processes lack anisotropic pattern transfer capability. However, in silicon, anisotropic wet etch processes are available for the fabrication of …
-
Fundamental Studies in Selective Wet Etching and Corrosion Processes for High-Performance Semiconductor Devices
… more complex, the role of cleaning solutions and etching chemistries are becoming important in enhancing yield and in reducing defects. This thesis demonstrates successful formulations that exhibit copper and tungsten compatibility, and are capable of Inter Layer Dielectric (ILD) cleaning and …
-
Fabrication Development Of Micron Scale Retroreflector Assays Using Wet Etching
… to a negative tone resist and incorporating a wet etch in place of a liftoff step. We have eliminated low yield steps and have replaced them with a more repeatable fabrication sequence. The total number of processing steps have been reduced and repeatability has been improved, resulting in an …
-
Resolution limits of metal assisted chemical etching of polysilicon
Patterning and etching high aspect ratio, sub-50 nanometer structures for 3D device architectures is becoming a critical challenge in advanced semiconductor device fabrication. Metal assisted chemical etching (MACE) is a wet etch process that has demonstrated very high aspect ratio structures in …
-
Hydrogen Sensing with Long-Range Surface Plasmon Membrane Waveguides
… lithography as well as a through-wafer silicon wet etch step. The devices are passively characterized using an optical cutback technique comparing the observed waveguide attenuation to that of simulated values showing good agreement. Sensing tests are performed with hydrogen concentrations up to …
-
Mechanism of fluoride-based etch and clean processes
Fluoride-containing solutions are widely used to etch silicon dioxide-based films. A critical issue in integrated circuit (IC) and microelectromechanical systems (MEMS) fabrication is achievement of adequate selectivity during the etching of different film materials when they are present in …
-
Characterization and fabrication of a (6H)-SiC as a piezoresistive pressure sensor for high temperature applications
… photoconductive selectivity techniques to etch the piezoresistors were developed. Techniques to wet etch the cavities in a dark current mode were developed, resulting in 25 um diaphragms free of etch-pits and hillocks. Average etch-rates between 0.6 and 0.8 um/min were achieved. Ti/TiN/Pt …
-
Grafted polymer monolayer brush as electron beam resist
… as negative tone e-beam resist with high dry etch resistance were studied. The main advantage of grafted polymer brush as electron beam is that it is applicable on non-flat or irregular surfaces. Although nanofabrication on non-flat surfaces has a lot of applications such as nanofabrication on …
-
Damage effects to Si-SiO2 structures due to reactive ion etching
… ? SiO<sub>2</sub> structures due to Reactive Ion Etching (RIE). The research was carried out on Si ? SiO<sub>2</sub> MOS capacitors which were fabricated using RIE and wet etch (Hydrofluoric acid etch (HFE)) Process. The experiment was carried out using CV technique and Ellipsometry. Various …
-
Liquid crystal adaptive planar optical devices
… accessing the Bragg grating vertically via a wet etch process, the substrates are precision machined using a dicing saw to allow side access. The result is significantly reduced hysteresis, with a maximum tuning range of over 1nm with the application of under 30V(pp). Tunable chirped Bragg …
-
Nanoscale 3D transfer printing for hybrid photonic device fabrication
… the difficulties of device release and wet-etch damage presented by using a novel porous GaN material. Using finite difference time domain (FDTD) simulation software the optimal LED layer structure for a 450nm resonant cavity LED (RCLED) was determined for combining with the …
-
III-Nitride Nanowire Deep-Ultraviolet Light Emitting Diodes
… In this work, the feasibility of using plasma etched arrays of nano- and micro-structures as alternatives to conventional mesa structures for emission of DUV light is investigated. New techniques for fabricating nanowire and micropillar array LEDs are developed, and a novel “inverse taper” …
-
Nanofabrication of direct positioning atomic force microscope (AFM) probes and a novel method to attain controllable lift-off
… the AFM tip. Those are evaporation, wet etch and dry etch. The basic concepts, working mechanism and important parameters of these three techniques are discussed. The third chapter presents detail of the AFM probe with its history, principle of operation, fabrication method and carbon …
-
The Impact Of Growth Conditions On Cubic Znmgo Ultraviolet Sensors
… devices. These extraordinary films are readily wet-etch-able, have inversion symmetric lattices, and are made of common and safe constituents. They also host a number of new exciting experimental and theoretical challenges. Here, the relation between growth conditions of the c-Zn1-xMgxO film and …
-
Synthesis and Terahertz Applications of Large-Area Monolayer Graphene
… from copper foil to SiO2/Si substrates by the wet-etch method with four types of copper etchants that are commonly used by researcher: HNO3, FeCl3, (NH4)2S2O8, and a commercial copper etchant. Further tests and analysis showed that the commercial copper etchant is the best for transfer purposes …
-
Development of A1GaN/GaN HBTs and HFETs for high power and high frequency operation.
… to buried p-type layers, exposed using a novel wet etch, were found to be superior when compared to those formed on dry etched structures. Utilising this technology in conjunction with a novel inverted n-p-n AlGaN/GaN HBT is found to increase the emitter-base heterojunction quality and also …
-
Design and Fabrication of a Nanocantilever for High-Speed Force Microscopy
… through focused ion beam milling; a subsequent wet etch into the underlying Si substrate suspended the structure. Then, using an active feedback system, electromigration was used to form the APC at 77 K and 10E-6 Torr. Progress was also made toward measuring cantilever motion with the APC …
-
Investigation on Sputter Ambient Oxygen Partial Pressure and Anneal Conditions on the Operation of Indium-Tungsten-Oxide Thin-Film Transistors
… (a-IGZO), exhibit sensitivity to moisture and wet etch processes, leading to suboptimal device performance and stability issues. To address these challenges, this study explores Indium Tungsten Oxide (IWO), an AOS devoid of Ga or Zn, as a potential material for fabricating high-performance and …
-
Functionalization and characterization of porous low-κ dielectrics.
… as damage to these materials caused by plasma etch, plasma ash, and wet etch processes are yet to be overcome. This dissertation reports the effects of triethoxyfluorosilane-based (TEFS) xerogel films when reacted with silylation agents. TEFS films were employed because they form robust silica …
-
Modeling, design, fabrication and demonstration of 3D IPAC glass power modules
… using both chemical vapor deposition (CVD) and wet-etch processes. However, it was noticed that the wet-etch process provided more control on the geometry, density and orientation of the nanowires. Si-oxide was thermally grown on the surface of the wires. A capacitance density of 200 nF/mm2 was …
Page 1 of 3