Global ETD Search
Search theses and dissertations gathered from participating repositories worldwide. Every result links back to the library that holds it. No account is needed.
Results
Showing 1 to 20 of 57 for “"window layer"”.
-
Copper Doped Window Layer for CdSe Solar Cells
CdSe solar cells with ZnTe as the window layer deposited by CSS process have shown Voc's around 630mV. However the currents were very low and also the voltages were not meeting the desired objectives. To improve the performance the contact energy at the ZnTe/Cu interface should be minimized by …
-
Investigating CdTe solar cell performance through glass/TCO selection and CdSe-based window layer engineering
… zinc oxide (MZO) as the n-type buffer layer. To address the first aim, three glass/TCO superstrates (TEC10, TEC12D, and a proprietary glass/TCO stack) were compared using optical transmission and reflection measurements, along with Hall effect characterization. Devices fabricated using …
-
Development of Window Layer for High Efficiency High Bandgap Cadmium Selenide Solar Cell for 4-Terminal Tandem Solar Cell Applications
… focuses on the development of conductive window layer for the development of a high performance, high bandgap solar cell. ZnSe, Cu2-xSe, and ZnSexTe1-x are investigated as viable window layers of the top cell. ZnSe in undoped form forms a good junction with CdSe films, but the Voc from …
-
Development of ternary oxides for use in advanced front contacts in cadmium telluride solar cells by magnetron sputtering
… external load. At the front of the device, the layers should be highly transparent to minimize parasitic absorption while also supporting electron transport to the external load. In this thesis, two sputter-deposited front contact layers were investigated with the goal of improving both …
-
Optimization of the front end of CDTE solar cells
The front end of CdTe solar cells consists of two layers: a transparent conducting oxide (TCO) layer and a window layer. New wider band gap materials, ZnMgO are being used to replace CdS as the window layer for the purpose of removing blue loss. For ZnMgO, three important parameters, including the …
-
A-Si:H saulės elementų su V205-x sluoksniu fotoelektrinių savybių ir krūvio pernašos tyrimas /
… Transport Properties of A-Si:H with V2O5-X Window Layer.
-
Optimization of the front contact to minimize short-circuit current losses in CdTe thin-film solar cells
… be extracted from the CdTe. The current standard window layer material, cadmium sulfide, has a low bandgap of 2.4 eV which can block over 20% of available light from being converted to mobile charge carriers. Reducing the thickness of this layer or replacing it with a higher-bandgap material can …
-
Atomic Layer Deposition for CZTS Solar Cells
… high-performance CZTS solar cells, nanoscale layer coating and interface modification by atomic layer deposition (ALD) is an effective strategy to improve the device performance. This thesis starts with the synthesis of ALD Zn1-xSnxO films for application as a buffer layer in CZTS solar cells. …
-
Heterojunction A1GaAs-GaAs solar cells for space applications
… solar cell is presented. The grid shadow and window layer effects, angle of incidence and the effects of the layer design parameters for AR-coating and window layer on the optical properties are considered in the calculations. A new structure for space solar cell which consists of double …
-
Nanostructured Semiconductor Device Design in Solar Cells
… and electrical robustness of planar CdS window layer and thus enhancing the quantum efficiency and the reliability of the CdS-CdTe solar cells. CdS nanowire window layer enables light transmission gain at 300nm-550nm. A nearly ideal spectral response of quantum efficiency at a wide …
-
CdS/CdTe Thin Film Solar Cells With Zinc Stannate Buffer Layer
… can be improved by integrating a ZTO buffer layer, which interdiffuses into the CdS layer during device fabrication. Reducing the thickness of CdS layer improves the QE in the blue spectral region without affecting the device performance. This buffer layer is expected to prevent the formation …
-
Development of plasma cleaning and plasma enhanced close space sublimation hardware for improving CdS/CdTe solar cells
… used to clean the transparent-conductive-oxide layer of the cell prior to the deposition of the CdS and CdTe layers. Plasma cleaning enables a reduction in CdS thickness by approximately 20 nm, while maintaining an improved cell voltage. Cell current was improved and cell efficiency was …
-
Development and characterization of chalcopyrite based thin film solar cells for photovoltaic technology applications
… characterized. The respective buffer- (ZnSe) and window-layers (ZnO) have been grown by low cost chemical and electrochemical techniques. The structural and optical properties of chalcopyrite single crystals and monocrystalline epitaxial layers have been analyzed by Optical Modulation Techniques. …
-
Effects of front and bottom texturings on gallium arsenide solar cell characteristics
… The texturing's were considered on the window layer and above the gold mirror layer for top and bottom texturing's respectively, with In0.5Ga0.5P and also with a combination of alternating metal dielectric slabs forming a meta structure over a gold layer on the window layer. Results for …
-
Growth and Characterization of ZnO for the Front Contact of Cu(In,Ga)Se2
ZnO window layers for CIGS solar cells are grown with a DC sputtering technique instead of a conventional RF sputtering technique. Transparent window layers and buffer layers are sputtered from the Zn target in the presence of Oxygen. The window layer is doped with Aluminum in order to achieve high …
-
A study of oxide/CdTe interfaces for CdTe photovoltaics using atomistic modeling
… growth and is now a major commercial player. However, the field has a few challenges to overcome until it reaches its full potential. The focus of this study is the interface between the CdTe-based absorber and the front window layer. Traditionally, cadmium sulfide has been used as the …
-
Pinholes and morphology of CdS films: the effect on the open circuit voltage of CdTe solar cells
… to many factors among which perfecting the window layer material can be a very important key. The best window layer material in CdTe solar cells was found to be cadmium sulfide (CdS). Usually thick CdS layers on the order of 125nm are used to ensure that the voltage of the solar device is as …
-
Heterojunctions and Schottky Diodes on Semiconductor Nanowires for Solar Cell Applications
… and electric properties of the light absorption layer as well as the window layer, utilizing nano template-assisted patterning and fabrication. In this dissertation, simulation and calculation of photocurrent generation in nanowires (NW) based heterojunction structure indicated that an estimated …
-
Improvement of GaAsP/SiGe tandem solar cell on silicon by optical characterisation, modelling, analysis, and design
… collection of carriers generated in the window layer is discovered. A double-layer antireflection coating (DARC) is designed and it is demonstrated that co-optimisation of the window layer results in low broadband reflection even in current-matched situations, enabling the use of a …
-
N-type CdTe Thin Films for Photovoltaic Applications
… studied as potential candidates for the p-type window layer. Scanning Electron Microscopy (SEM) Energy-dispersive X-ray Spectrometry (EDS) and X-Ray Diffraction (XRD) were used to study the film properties of the n-CdTe absorber layer and the p-type window layer. The complete devices were …
Page 1 of 3