{"id":{"repo_id":"mcmaster","oai_identifier":"oai:macsphere.mcmaster.ca:11375/25374"},"canonical_url":"https://search.ndltd.org/etd/mcmaster/oai:macsphere.mcmaster.ca:11375/25374","repository":{"repo_id":"mcmaster","name":"McMaster University","base_url":"https://macsphere.mcmaster.ca/server/oai/request"},"display":{"title":"Design of Time-Gated CMOS SPADs Towards High-Performance Imagers","abstract":"SPAD (Single-Photon Avalanche Diode) sensors, capable of detecting down to the single photon level for ultimate sensitivity, have shown great promise as the photodetector of choice for next-generation devices used in positron emission tomography, fluorescence lifetime imaging, light detection and ranging, and more. SPAD fabrication has shifted recently towards custom technologies, 3D stacked designs, and post-processing steps (micro-lenses) to improve performance at the expense of increased cost and complexity. This thesis explores time-gating and multi-junction techniques to improve SPAD performance in standard planar CMOS (Complementary Metal-Oxide-Semiconductor) processes to take advantage of their potential for monolithic integration with other mixed-signal circuitry for simple, low-cost, high-performance imaging solutions. An unbuffered triple-junction SPAD was fabricated to investigate the potential for wavelength distinction, however the top two junctions (n+/p-well and p-well/deep n-well) showed excessive noise, and the deepest junction exhibited a similar spectral response to the top junction, potentially due to a large influence from the process layers over the active area. A time-gated SPAD pixel based on the top junction was also designed and fabricated in the TSMC standard 65 nm CMOS process with a fill-factor of 28.6%. At an excess voltage of 300 mV, it achieved a peak photon detection efficiency of ~3.5% at 440 nm, <1% afterpulsing probability for hold-off times >22ns, and <200 ps timing jitter. Lastly, the potential for high-performance CMOS imaging systems was demonstrated through the development of a prototype open-source, low-cost, highspeed camera built with standard commodity hardware. It achieved 211 frames per second (fps) at its maximum resolution of 1280x1024, and up to 2329 fps at a 256x256 resolution, with a cost well under $1000 USD. It was found to be very competitive to current low-cost, commercial highspeed cameras using a new figure-of-merit comparison and was tested for biological microscopy applications involving C. elegans worms.","abstract_html":"SPAD (Single-Photon Avalanche Diode) sensors, capable of detecting down to the single photon level for ultimate sensitivity, have shown great promise as the photodetector of choice for next-generation devices used in positron emission tomography, fluorescence lifetime imaging, light detection and ranging, and more. SPAD fabrication has shifted recently towards custom technologies, 3D stacked designs, and post-processing steps (micro-lenses) to improve performance at the expense of increased cost and complexity. This thesis explores time-gating and multi-junction techniques to improve SPAD performance in standard planar CMOS (Complementary Metal-Oxide-Semiconductor) processes to take advantage of their potential for monolithic integration with other mixed-signal circuitry for simple, low-cost, high-performance imaging solutions. An unbuffered triple-junction SPAD was fabricated to investigate the potential for wavelength distinction, however the top two junctions (n+/p-well and p-well/deep n-well) showed excessive noise, and the deepest junction exhibited a similar spectral response to the top junction, potentially due to a large influence from the process layers over the active area. A time-gated SPAD pixel based on the top junction was also designed and fabricated in the TSMC standard 65 nm CMOS process with a fill-factor of 28.6%. At an excess voltage of 300 mV, it achieved a peak photon detection efficiency of ~3.5% at 440 nm, &lt;1% afterpulsing probability for hold-off times &gt;22ns, and &lt;200 ps timing jitter. Lastly, the potential for high-performance CMOS imaging systems was demonstrated through the development of a prototype open-source, low-cost, highspeed camera built with standard commodity hardware. It achieved 211 frames per second (fps) at its maximum resolution of 1280x1024, and up to 2329 fps at a 256x256 resolution, with a cost well under $1000 USD. It was found to be very competitive to current low-cost, commercial highspeed cameras using a new figure-of-merit comparison and was tested for biological microscopy applications involving C. elegans worms.","abstract_has_math":false,"creators":["Chalich, Yamn"],"institution":null,"degree_name":null,"degree_level":null,"degree_discipline":null,"degree_department":"Electrical and Computer Engineering","school":null,"contributors":[],"advisors":["Deen, Jamal"],"committee_chairs":[],"committee_members":[],"year":2020,"date_issued":"2020","date_published":"2020","updated_at":"2026-11-19T05:56:00Z","subjects":[],"languages":["en"],"rights":[],"rights_urls":[],"identifier_entries":[{"key":"dc:identifier.uri","label":"Identifier URI","values":["https://doi.org/10.71548/23657"],"render_values":[{"text":"https://doi.org/10.71548/23657","href":"https://doi.org/10.71548/23657","code":true}]}],"person_identifier_entries":[]},"links":{"outbound_url":"http://hdl.handle.net/11375/25374","outbound_label":"Handle","outbound_source":"dc:identifier.uri","record_url":"http://hdl.handle.net/11375/25374","record_label":"Repository record","record_kind":"handle","record_source":"dc:identifier.uri","download_url":null,"download_label":null,"download_source":null,"access_status":null,"embargo_until":null,"access_note":null},"source_record":{"url":"https://macsphere.mcmaster.ca/server/oai/request?verb=GetRecord&metadataPrefix=dim&identifier=oai%3Amacsphere.mcmaster.ca%3A11375%2F25374","prefix":"dim"},"metadata_groups":[{"id":"people","label":"People","entries":[{"key":"dc:contributor.advisor","label":"Advisor","values":["Deen, Jamal"]},{"key":"dc:contributor.department","label":"Department","values":["Electrical and Computer Engineering"]},{"key":"dc:creator","label":"Author","values":["Chalich, Yamn"]}]},{"id":"academic_context","label":"Academic Context","entries":[{"key":"dc:date.accessioned","label":"Dc Date Accessioned","values":["2020-04-14T06:20:08Z"]},{"key":"dc:date.available","label":"Dc Date Available","values":["2020-04-14T06:20:08Z"]},{"key":"dc:date.issued","label":"Date","values":["2020"]},{"key":"dc:type","label":"Dc Type","values":["Thesis"]}]},{"id":"language_rights","label":"Language and Rights","entries":[{"key":"dc:language.iso","label":"Language (ISO)","values":["en"]}]},{"id":"identifiers","label":"Identifiers","entries":[{"key":"dc:identifier.uri","label":"Identifier URI","values":["http://hdl.handle.net/11375/25374","https://doi.org/10.71548/23657"]}]},{"id":"additional","label":"Additional Metadata","entries":[{"key":"dc:description.abstract","label":"Abstract","values":["SPAD (Single-Photon Avalanche Diode) sensors, capable of detecting down to the single photon level for ultimate sensitivity, have shown great promise as the photodetector of choice for next-generation devices used in positron emission tomography, fluorescence lifetime imaging, light detection and ranging, and more. SPAD fabrication has shifted recently towards custom technologies, 3D stacked designs, and post-processing steps (micro-lenses) to improve performance at the expense of increased cost and complexity. This thesis explores time-gating and multi-junction techniques to improve SPAD performance in standard planar CMOS (Complementary Metal-Oxide-Semiconductor) processes to take advantage of their potential for monolithic integration with other mixed-signal circuitry for simple, low-cost, high-performance imaging solutions. An unbuffered triple-junction SPAD was fabricated to investigate the potential for wavelength distinction, however the top two junctions (n+/p-well and p-well/deep n-well) showed excessive noise, and the deepest junction exhibited a similar spectral response to the top junction, potentially due to a large influence from the process layers over the active area. A time-gated SPAD pixel based on the top junction was also designed and fabricated in the TSMC standard 65 nm CMOS process with a fill-factor of 28.6%. At an excess voltage of 300 mV, it achieved a peak photon detection efficiency of ~3.5% at 440 nm, <1% afterpulsing probability for hold-off times >22ns, and <200 ps timing jitter. Lastly, the potential for high-performance CMOS imaging systems was demonstrated through the development of a prototype open-source, low-cost, highspeed camera built with standard commodity hardware. It achieved 211 frames per second (fps) at its maximum resolution of 1280x1024, and up to 2329 fps at a 256x256 resolution, with a cost well under $1000 USD. It was found to be very competitive to current low-cost, commercial highspeed cameras using a new figure-of-merit comparison and was tested for biological microscopy applications involving C. elegans worms."]},{"key":"dc:description.abstractgeneral","label":"General Abstract","values":["The CMOS (Complementary Metal-Oxide-Semiconductor) technology process has made accessible the development of highspeed digital circuitry and sophisticated image sensor arrays. SPADs (Single-Photon Avalanche Diodes) capable of detecting single photons for ultimate sensitivity can be fabricated in a standard CMOS process and paves the way for low-cost, next-generation, high-performance, and miniature imaging solutions. In this thesis, a time-gated SPAD implemented in a smaller CMOS technology node not typically investigated in the literature was tested and showed strong overall performance despite suffering from increased noise. A multi-junction SPAD capable of increased photon detecting capabilities was also explored and a time-gated, dual-junction solution was designed and simulated to take advantage of both structures while overcoming the difficulties of integrating them. Finally, a low-cost, highspeed camera is built with standard commodity hardware and a CMOS image sensor to demonstrate the capabilities and ease of developing high-performance imagers comparable to or better than commercial solutions."]},{"key":"dc:description.degree","label":"Dc Description Degree","values":["Master of Applied Science (MASc)"]},{"key":"dc:title","label":"Title","values":["Design of Time-Gated CMOS SPADs Towards High-Performance Imagers"]},{"key":"dc:title.alternative","label":"Alternative Title","values":["Design of CMOS SPADs Towards High-Performance Imagers"]},{"key":"others:access_status","label":"Others Access Status","values":["open.access"]}]}],"canonical_facts":{"dc:contributor.advisor":["Deen, Jamal"],"dc:contributor.department":["Electrical and Computer Engineering"],"dc:creator":["Chalich, Yamn"],"dc:date.accessioned":["2020-04-14T06:20:08Z"],"dc:date.available":["2020-04-14T06:20:08Z"],"dc:date.issued":["2020"],"dc:description.abstract":["SPAD (Single-Photon Avalanche Diode) sensors, capable of detecting down to the single photon level for ultimate sensitivity, have shown great promise as the photodetector of choice for next-generation devices used in positron emission tomography, fluorescence lifetime imaging, light detection and ranging, and more. SPAD fabrication has shifted recently towards custom technologies, 3D stacked designs, and post-processing steps (micro-lenses) to improve performance at the expense of increased cost and complexity. This thesis explores time-gating and multi-junction techniques to improve SPAD performance in standard planar CMOS (Complementary Metal-Oxide-Semiconductor) processes to take advantage of their potential for monolithic integration with other mixed-signal circuitry for simple, low-cost, high-performance imaging solutions. An unbuffered triple-junction SPAD was fabricated to investigate the potential for wavelength distinction, however the top two junctions (n+/p-well and p-well/deep n-well) showed excessive noise, and the deepest junction exhibited a similar spectral response to the top junction, potentially due to a large influence from the process layers over the active area. A time-gated SPAD pixel based on the top junction was also designed and fabricated in the TSMC standard 65 nm CMOS process with a fill-factor of 28.6%. At an excess voltage of 300 mV, it achieved a peak photon detection efficiency of ~3.5% at 440 nm, <1% afterpulsing probability for hold-off times >22ns, and <200 ps timing jitter. Lastly, the potential for high-performance CMOS imaging systems was demonstrated through the development of a prototype open-source, low-cost, highspeed camera built with standard commodity hardware. It achieved 211 frames per second (fps) at its maximum resolution of 1280x1024, and up to 2329 fps at a 256x256 resolution, with a cost well under $1000 USD. It was found to be very competitive to current low-cost, commercial highspeed cameras using a new figure-of-merit comparison and was tested for biological microscopy applications involving C. elegans worms."],"dc:description.abstractgeneral":["The CMOS (Complementary Metal-Oxide-Semiconductor) technology process has made accessible the development of highspeed digital circuitry and sophisticated image sensor arrays. SPADs (Single-Photon Avalanche Diodes) capable of detecting single photons for ultimate sensitivity can be fabricated in a standard CMOS process and paves the way for low-cost, next-generation, high-performance, and miniature imaging solutions. In this thesis, a time-gated SPAD implemented in a smaller CMOS technology node not typically investigated in the literature was tested and showed strong overall performance despite suffering from increased noise. A multi-junction SPAD capable of increased photon detecting capabilities was also explored and a time-gated, dual-junction solution was designed and simulated to take advantage of both structures while overcoming the difficulties of integrating them. Finally, a low-cost, highspeed camera is built with standard commodity hardware and a CMOS image sensor to demonstrate the capabilities and ease of developing high-performance imagers comparable to or better than commercial solutions."],"dc:description.degree":["Master of Applied Science (MASc)"],"dc:identifier.uri":["http://hdl.handle.net/11375/25374","https://doi.org/10.71548/23657"],"dc:language.iso":["en"],"dc:title":["Design of Time-Gated CMOS SPADs Towards High-Performance Imagers"],"dc:title.alternative":["Design of CMOS SPADs Towards High-Performance Imagers"],"dc:type":["Thesis"],"others:access_status":["open.access"]},"updated_at":"2026-11-19T05:56:00Z"}