{"id":{"repo_id":"mtu","oai_identifier":"oai:digitalcommons.mtu.edu:etdr-1329"},"canonical_url":"https://search.ndltd.org/etd/mtu/oai:digitalcommons.mtu.edu:etdr-1329","repository":{"repo_id":"mtu","name":"Michigan Technological University","base_url":"https://digitalcommons.mtu.edu/do/oai/"},"display":{"title":"ALLOYING OF THIN-WALL DUCTILE IRON CASTINGS","abstract":"Lightweight materials are an essential component in meeting light vehicle fuel economy standards. Although ductile iron has high strength, toughness, and cost effectiveness, it is usually not thought of for lightweighting solutions because ferrous materials, in general, are thought of as high density. One strategy to address this issue is to produce sound, thin wall ductile iron castings. This study evaluates improvements resulting in alloying of thin wall ductile iron castings. Two, three, four and six-millimeter-thick sections were cast in chemically bonded sand molds and evaluated by optical microscopy, ultrasonic modulus, Brinell hardness and tensile testing. Increasing cooling rates in thin castings will result in a fine, pearlitic lamellar spacing and a fine microstructure. The fast cooling rate inhibits the distance that carbon will diffuse. Fine pearlitic microstructures have shown a promising increase in both yield and tensile strengths. Thin section ductile iron can have increased mechanical properties as opposed to a thicker section size because of a finer microstructure. However, sufficient ductility is challenging. An increase in yield and tensile strength to weight ratio will provide a new approach to not only automotive components but to a wide range of others.","abstract_html":"Lightweight materials are an essential component in meeting light vehicle fuel economy standards. Although ductile iron has high strength, toughness, and cost effectiveness, it is usually not thought of for lightweighting solutions because ferrous materials, in general, are thought of as high density. One strategy to address this issue is to produce sound, thin wall ductile iron castings. This study evaluates improvements resulting in alloying of thin wall ductile iron castings. Two, three, four and six-millimeter-thick sections were cast in chemically bonded sand molds and evaluated by optical microscopy, ultrasonic modulus, Brinell hardness and tensile testing. Increasing cooling rates in thin castings will result in a fine, pearlitic lamellar spacing and a fine microstructure. The fast cooling rate inhibits the distance that carbon will diffuse. Fine pearlitic microstructures have shown a promising increase in both yield and tensile strengths. Thin section ductile iron can have increased mechanical properties as opposed to a thicker section size because of a finer microstructure. However, sufficient ductility is challenging. An increase in yield and tensile strength to weight ratio will provide a new approach to not only automotive components but to a wide range of others.","abstract_has_math":false,"creators":["Tankersley, Stephanie"],"institution":null,"degree_name":"Master of Science in Mechanical Engineering (MS)","degree_level":"Campus Access Master's Thesis","degree_discipline":"Department of Mechanical Engineering-Engineering Mechanics","degree_department":null,"school":null,"contributors":["Paul Sanders","Gregory Odegard"],"advisors":[],"committee_chairs":[],"committee_members":["Kathy Hayrynen"],"year":null,"date_issued":"","date_published":null,"updated_at":"2026-11-19T08:16:54Z","subjects":["ductile iron","castings","iron","thin castings","thin walled castings","alloying","Metallurgy"],"languages":[],"rights":[],"rights_urls":[],"identifier_entries":[{"key":"dc:identifier","label":"Identifier","values":["https://digitalcommons.mtu.edu/etdr/248"],"render_values":[{"text":"https://digitalcommons.mtu.edu/etdr/248","href":"https://digitalcommons.mtu.edu/etdr/248","code":true}]}],"person_identifier_entries":[]},"links":{"outbound_url":"https://doi.org/10.37099/mtu.dc.etdr/248","outbound_label":"DOI","outbound_source":"dc:identifier","record_url":"https://doi.org/10.37099/mtu.dc.etdr/248","record_label":"Repository record","record_kind":"doi","record_source":"dc:identifier","download_url":null,"download_label":null,"download_source":null,"access_status":null,"embargo_until":null,"access_note":null},"source_record":{"url":"https://digitalcommons.mtu.edu/do/oai/?verb=GetRecord&metadataPrefix=oai_etdms&identifier=oai%3Adigitalcommons.mtu.edu%3Aetdr-1329","prefix":"oai_etdms"},"metadata_groups":[{"id":"people","label":"People","entries":[{"key":"dc:contributor","label":"Contributor","values":["Paul Sanders","Gregory Odegard"]},{"key":"dc:contributor.committeemember","label":"Committee Member","values":["Kathy Hayrynen"]},{"key":"dc:creator","label":"Author","values":["Tankersley, Stephanie"]}]},{"id":"academic_context","label":"Academic Context","entries":[{"key":"dc:date.available","label":"Dc Date Available","values":["2017-12-31T08:00:00Z"]},{"key":"dc:date.created","label":"Dc Date Created","values":["2016-01-01T08:00:00Z"]},{"key":"thesis:degree_discipline","label":"Discipline","values":["Department of Mechanical Engineering-Engineering Mechanics"]},{"key":"thesis:degree_level","label":"Degree Level","values":["Campus Access Master's Thesis"]},{"key":"thesis:degree_name","label":"Degree Name","values":["Master of Science in Mechanical Engineering (MS)"]}]},{"id":"subjects_keywords","label":"Subjects and Keywords","entries":[{"key":"dc:subject","label":"Dc Subject","values":["ductile iron","castings","iron","thin castings","thin walled castings","alloying","Metallurgy"]}]},{"id":"identifiers","label":"Identifiers","entries":[{"key":"dc:identifier","label":"Identifier","values":["10.37099/mtu.dc.etdr/248","https://digitalcommons.mtu.edu/etdr/248"]}]},{"id":"additional","label":"Additional Metadata","entries":[{"key":"dc:description.abstract","label":"Abstract","values":["Lightweight materials are an essential component in meeting light vehicle fuel economy standards. Although ductile iron has high strength, toughness, and cost effectiveness, it is usually not thought of for lightweighting solutions because ferrous materials, in general, are thought of as high density. One strategy to address this issue is to produce sound, thin wall ductile iron castings. This study evaluates improvements resulting in alloying of thin wall ductile iron castings. Two, three, four and six-millimeter-thick sections were cast in chemically bonded sand molds and evaluated by optical microscopy, ultrasonic modulus, Brinell hardness and tensile testing. Increasing cooling rates in thin castings will result in a fine, pearlitic lamellar spacing and a fine microstructure. The fast cooling rate inhibits the distance that carbon will diffuse. Fine pearlitic microstructures have shown a promising increase in both yield and tensile strengths. Thin section ductile iron can have increased mechanical properties as opposed to a thicker section size because of a finer microstructure. However, sufficient ductility is challenging. An increase in yield and tensile strength to weight ratio will provide a new approach to not only automotive components but to a wide range of others."]},{"key":"dc:description.note","label":"Dc Description Note","values":["<p>Figures 3, 4, 5 in particular question are schematics. They like most of the figures in this document were all created in powerpoint by myself. The figures are based off of the sources that are in the citation of the figure.</p>"]},{"key":"dc:title","label":"Title","values":["ALLOYING OF THIN-WALL DUCTILE IRON CASTINGS"]}]}],"canonical_facts":{"dc:contributor":["Paul Sanders","Gregory Odegard"],"dc:contributor.committeemember":["Kathy Hayrynen"],"dc:creator":["Tankersley, Stephanie"],"dc:date.available":["2017-12-31T08:00:00Z"],"dc:date.created":["2016-01-01T08:00:00Z"],"dc:description.abstract":["Lightweight materials are an essential component in meeting light vehicle fuel economy standards. Although ductile iron has high strength, toughness, and cost effectiveness, it is usually not thought of for lightweighting solutions because ferrous materials, in general, are thought of as high density. One strategy to address this issue is to produce sound, thin wall ductile iron castings. This study evaluates improvements resulting in alloying of thin wall ductile iron castings. Two, three, four and six-millimeter-thick sections were cast in chemically bonded sand molds and evaluated by optical microscopy, ultrasonic modulus, Brinell hardness and tensile testing. Increasing cooling rates in thin castings will result in a fine, pearlitic lamellar spacing and a fine microstructure. The fast cooling rate inhibits the distance that carbon will diffuse. Fine pearlitic microstructures have shown a promising increase in both yield and tensile strengths. Thin section ductile iron can have increased mechanical properties as opposed to a thicker section size because of a finer microstructure. However, sufficient ductility is challenging. An increase in yield and tensile strength to weight ratio will provide a new approach to not only automotive components but to a wide range of others."],"dc:description.note":["<p>Figures 3, 4, 5 in particular question are schematics. They like most of the figures in this document were all created in powerpoint by myself. The figures are based off of the sources that are in the citation of the figure.</p>"],"dc:identifier":["10.37099/mtu.dc.etdr/248","https://digitalcommons.mtu.edu/etdr/248"],"dc:subject":["ductile iron","castings","iron","thin castings","thin walled castings","alloying","Metallurgy"],"dc:title":["ALLOYING OF THIN-WALL DUCTILE IRON CASTINGS"],"thesis:degree_discipline":["Department of Mechanical Engineering-Engineering Mechanics"],"thesis:degree_level":["Campus Access Master's Thesis"],"thesis:degree_name":["Master of Science in Mechanical Engineering (MS)"]},"updated_at":"2026-11-19T08:16:54Z"}