{"id":{"repo_id":"mtu","oai_identifier":"oai:digitalcommons.mtu.edu:etdr-2827"},"canonical_url":"https://search.ndltd.org/etd/mtu/oai:digitalcommons.mtu.edu:etdr-2827","repository":{"repo_id":"mtu","name":"Michigan Technological University","base_url":"https://digitalcommons.mtu.edu/do/oai/"},"display":{"title":"IMPROVED DUCTILITY IN AN ARTIFICIALLY AGED AL-ZN-MG ALLOY WITH MN ADDITIONS","abstract":"Further lightweighting of aluminum-intensive vehicle (AIV) body structures is of high priority to increase vehicle range. 7000-series alloys can offer in-service strength levels of 500 MPa which could provide a 30% weight reduction over existing 6000 series structural parts. However, these alloys do not have a stable T4 temper and are not able to be conventionally stamped due to low formability. Hot stamping has been demonstrated as a viable method to forming 7000-series part where a blank is solution heat treated, formed and simultaneously quenched, followed by a two-step artificial age treatment raising the part to its in-service strength. A key challenge to implementing a hot stamped and two-step aged 7000-series part is that they are not readily joinable via self-pierce riveting (SPR), because they lack room-temperature ductility. Precipitation-hardened alloys like 7000-series alloys are susceptible to localized planar slip, which degrades the local ductility needed to form a successful SPR joint. In this work a strategy to reduce planar slip was proposed, in which a dispersion of sub-micron sized, non-shearable, Mn-based dispersoids was added to a dense distribution of nano-sized strengthening precipitates. Model Al-Zn-Mg alloys with various additions of Mn were cast, homogenized, and fabricated into wrought sheet material that was solution heat treated and two-step artificially aged. In the two-step aged condition, the addition of Mn increased ultimate tensile strength, but did not affect tensile yield strength. Mn additions improved ductility due to the formation of Mn-dispersoids that facilitated dislocation cross-slip onto adjacent slip planes, resulting in a more finely-spaced arrangement of slip bands that reduced grain boundary stress localization. A more homogenous slip distribution was observed in TEM and slip-line spacing was quantified using EBSD data collected from strained specimens that were thermo-mechanically processed to have similar grain sizes.","abstract_html":"Further lightweighting of aluminum-intensive vehicle (AIV) body structures is of high priority to increase vehicle range. 7000-series alloys can offer in-service strength levels of 500 MPa which could provide a 30% weight reduction over existing 6000 series structural parts. However, these alloys do not have a stable T4 temper and are not able to be conventionally stamped due to low formability. Hot stamping has been demonstrated as a viable method to forming 7000-series part where a blank is solution heat treated, formed and simultaneously quenched, followed by a two-step artificial age treatment raising the part to its in-service strength. A key challenge to implementing a hot stamped and two-step aged 7000-series part is that they are not readily joinable via self-pierce riveting (SPR), because they lack room-temperature ductility. Precipitation-hardened alloys like 7000-series alloys are susceptible to localized planar slip, which degrades the local ductility needed to form a successful SPR joint. In this work a strategy to reduce planar slip was proposed, in which a dispersion of sub-micron sized, non-shearable, Mn-based dispersoids was added to a dense distribution of nano-sized strengthening precipitates. Model Al-Zn-Mg alloys with various additions of Mn were cast, homogenized, and fabricated into wrought sheet material that was solution heat treated and two-step artificially aged. In the two-step aged condition, the addition of Mn increased ultimate tensile strength, but did not affect tensile yield strength. Mn additions improved ductility due to the formation of Mn-dispersoids that facilitated dislocation cross-slip onto adjacent slip planes, resulting in a more finely-spaced arrangement of slip bands that reduced grain boundary stress localization. A more homogenous slip distribution was observed in TEM and slip-line spacing was quantified using EBSD data collected from strained specimens that were thermo-mechanically processed to have similar grain sizes.","abstract_has_math":false,"creators":["Freiberg, Daniel S."],"institution":null,"degree_name":"Doctor of Philosophy in Materials Science and Engineering (PhD)","degree_level":"Campus Access Dissertation","degree_discipline":"Department of Materials Science and Engineering","degree_department":null,"school":null,"contributors":["Paul G. Sanders"],"advisors":[],"committee_chairs":[],"committee_members":["Douglas J. Swenson","Stephen A. Hackney","Walter W. Milligan","Mei Li"],"year":null,"date_issued":"","date_published":null,"updated_at":"2026-11-19T08:19:03Z","subjects":["aluminum","al-zn-mg","deformation","ductility","Mn dispersoid","cross-slip","fracture","Metallurgy","Structural Materials"],"languages":[],"rights":[],"rights_urls":[],"identifier_entries":[{"key":"dc:identifier","label":"Identifier","values":["https://digitalcommons.mtu.edu/etdr/1698"],"render_values":[{"text":"https://digitalcommons.mtu.edu/etdr/1698","href":"https://digitalcommons.mtu.edu/etdr/1698","code":true}]}],"person_identifier_entries":[]},"links":{"outbound_url":"https://doi.org/10.37099/mtu.dc.etdr/1698","outbound_label":"DOI","outbound_source":"dc:identifier","record_url":"https://doi.org/10.37099/mtu.dc.etdr/1698","record_label":"Repository record","record_kind":"doi","record_source":"dc:identifier","download_url":null,"download_label":null,"download_source":null,"access_status":null,"embargo_until":null,"access_note":null},"source_record":{"url":"https://digitalcommons.mtu.edu/do/oai/?verb=GetRecord&metadataPrefix=oai_etdms&identifier=oai%3Adigitalcommons.mtu.edu%3Aetdr-2827","prefix":"oai_etdms"},"metadata_groups":[{"id":"people","label":"People","entries":[{"key":"dc:contributor","label":"Contributor","values":["Paul G. Sanders"]},{"key":"dc:contributor.committeemember","label":"Committee Member","values":["Douglas J. Swenson","Stephen A. Hackney","Walter W. Milligan","Mei Li"]},{"key":"dc:creator","label":"Author","values":["Freiberg, Daniel S."]}]},{"id":"academic_context","label":"Academic Context","entries":[{"key":"dc:date.created","label":"Dc Date Created","values":["2023-01-01T08:00:00Z"]},{"key":"thesis:degree_discipline","label":"Discipline","values":["Department of Materials Science and Engineering"]},{"key":"thesis:degree_level","label":"Degree Level","values":["Campus Access Dissertation"]},{"key":"thesis:degree_name","label":"Degree Name","values":["Doctor of Philosophy in Materials Science and Engineering (PhD)"]}]},{"id":"subjects_keywords","label":"Subjects and Keywords","entries":[{"key":"dc:subject","label":"Dc Subject","values":["aluminum","al-zn-mg","deformation","ductility","Mn dispersoid","cross-slip","fracture","Metallurgy","Structural Materials"]}]},{"id":"identifiers","label":"Identifiers","entries":[{"key":"dc:identifier","label":"Identifier","values":["10.37099/mtu.dc.etdr/1698","https://digitalcommons.mtu.edu/etdr/1698"]}]},{"id":"additional","label":"Additional Metadata","entries":[{"key":"dc:description.abstract","label":"Abstract","values":["Further lightweighting of aluminum-intensive vehicle (AIV) body structures is of high priority to increase vehicle range. 7000-series alloys can offer in-service strength levels of 500 MPa which could provide a 30% weight reduction over existing 6000 series structural parts. However, these alloys do not have a stable T4 temper and are not able to be conventionally stamped due to low formability. Hot stamping has been demonstrated as a viable method to forming 7000-series part where a blank is solution heat treated, formed and simultaneously quenched, followed by a two-step artificial age treatment raising the part to its in-service strength. A key challenge to implementing a hot stamped and two-step aged 7000-series part is that they are not readily joinable via self-pierce riveting (SPR), because they lack room-temperature ductility. Precipitation-hardened alloys like 7000-series alloys are susceptible to localized planar slip, which degrades the local ductility needed to form a successful SPR joint. In this work a strategy to reduce planar slip was proposed, in which a dispersion of sub-micron sized, non-shearable, Mn-based dispersoids was added to a dense distribution of nano-sized strengthening precipitates. Model Al-Zn-Mg alloys with various additions of Mn were cast, homogenized, and fabricated into wrought sheet material that was solution heat treated and two-step artificially aged. In the two-step aged condition, the addition of Mn increased ultimate tensile strength, but did not affect tensile yield strength. Mn additions improved ductility due to the formation of Mn-dispersoids that facilitated dislocation cross-slip onto adjacent slip planes, resulting in a more finely-spaced arrangement of slip bands that reduced grain boundary stress localization. A more homogenous slip distribution was observed in TEM and slip-line spacing was quantified using EBSD data collected from strained specimens that were thermo-mechanically processed to have similar grain sizes."]},{"key":"dc:title","label":"Title","values":["IMPROVED DUCTILITY IN AN ARTIFICIALLY AGED AL-ZN-MG ALLOY WITH MN ADDITIONS"]}]}],"canonical_facts":{"dc:contributor":["Paul G. Sanders"],"dc:contributor.committeemember":["Douglas J. Swenson","Stephen A. Hackney","Walter W. Milligan","Mei Li"],"dc:creator":["Freiberg, Daniel S."],"dc:date.created":["2023-01-01T08:00:00Z"],"dc:description.abstract":["Further lightweighting of aluminum-intensive vehicle (AIV) body structures is of high priority to increase vehicle range. 7000-series alloys can offer in-service strength levels of 500 MPa which could provide a 30% weight reduction over existing 6000 series structural parts. However, these alloys do not have a stable T4 temper and are not able to be conventionally stamped due to low formability. Hot stamping has been demonstrated as a viable method to forming 7000-series part where a blank is solution heat treated, formed and simultaneously quenched, followed by a two-step artificial age treatment raising the part to its in-service strength. A key challenge to implementing a hot stamped and two-step aged 7000-series part is that they are not readily joinable via self-pierce riveting (SPR), because they lack room-temperature ductility. Precipitation-hardened alloys like 7000-series alloys are susceptible to localized planar slip, which degrades the local ductility needed to form a successful SPR joint. In this work a strategy to reduce planar slip was proposed, in which a dispersion of sub-micron sized, non-shearable, Mn-based dispersoids was added to a dense distribution of nano-sized strengthening precipitates. Model Al-Zn-Mg alloys with various additions of Mn were cast, homogenized, and fabricated into wrought sheet material that was solution heat treated and two-step artificially aged. In the two-step aged condition, the addition of Mn increased ultimate tensile strength, but did not affect tensile yield strength. Mn additions improved ductility due to the formation of Mn-dispersoids that facilitated dislocation cross-slip onto adjacent slip planes, resulting in a more finely-spaced arrangement of slip bands that reduced grain boundary stress localization. A more homogenous slip distribution was observed in TEM and slip-line spacing was quantified using EBSD data collected from strained specimens that were thermo-mechanically processed to have similar grain sizes."],"dc:identifier":["10.37099/mtu.dc.etdr/1698","https://digitalcommons.mtu.edu/etdr/1698"],"dc:subject":["aluminum","al-zn-mg","deformation","ductility","Mn dispersoid","cross-slip","fracture","Metallurgy","Structural Materials"],"dc:title":["IMPROVED DUCTILITY IN AN ARTIFICIALLY AGED AL-ZN-MG ALLOY WITH MN ADDITIONS"],"thesis:degree_discipline":["Department of Materials Science and Engineering"],"thesis:degree_level":["Campus Access Dissertation"],"thesis:degree_name":["Doctor of Philosophy in Materials Science and Engineering (PhD)"]},"updated_at":"2026-11-19T08:19:03Z"}