{"id":{"repo_id":"mtu","oai_identifier":"oai:digitalcommons.mtu.edu:etdr-3091"},"canonical_url":"https://search.ndltd.org/etd/mtu/oai:digitalcommons.mtu.edu:etdr-3091","repository":{"repo_id":"mtu","name":"Michigan Technological University","base_url":"https://digitalcommons.mtu.edu/do/oai/"},"display":{"title":"DESIGN OF ALUMINUM-COPPER ALLOY WITH SCANDIUM IN SOLUTION","abstract":"The 2xxx series of precipitation-strengthened aluminum-copper alloys are commonly used in high-temperature applications (up to 300°C) where lightweight metals are required. Scandium additions to aluminum-copper alloys have gained recent academic interest due to improved high-temperature mechanical properties, by forming coarsening- resistant Al3Sc dispersoids and stabilization of θ′ precipitates. However, gaps in knowledge about the effects of scandium present a challenge to successful commercialization of aluminum-copper-scandium alloys. This work seeks to explore these knowledge gaps and ultimately design and test a commercially feasible aluminum- copper alloy with scandium. To better understand the processing conditions required to avoid the detrimental W-phase (Al8Cu4Sc), castings were produced with a wide range of solidification rates and heat treatments. It was shown that the only feasible heat treatment is a single-step homogenization with copper below 4 wt%, and that higher copper or multi-step homogenization will lead to the formation of W-phase. W-phase results precipitate-free zones which lower the hardness of the resulting microstructure. Using a 3.5 wt% copper sample combined with a single-step homogenization, the effects of scandium in solution on precipitation of copper-rich precipitates are studied. Scandium in solution stabilizes θ″ and θ‴ precipitates over θ′ when aging at 160°C, which is supported by density functional theory calculations that show a significant reduction in the interaction energy of θ″, θ‴, and GP zones with the addition of scandium. Finally, an engineered alloy with low copper and scandium in solution is tested in comparison to AA2219 and is shown to have similar high-temperature strength while having a 60% increase in the fracture toughness. Transmission electron microscopy shows that θ′ precipitates in the scandium-containing alloy have larger aspect ratios and a preference for {100} semi-coherent interfaces. This work expands knowledge of the processing conditions required for a commercially feasible aluminum-copper-scandium alloy and demonstrates an alloy design strategy for this system.","abstract_html":"The 2xxx series of precipitation-strengthened aluminum-copper alloys are commonly used in high-temperature applications (up to 300°C) where lightweight metals are required. Scandium additions to aluminum-copper alloys have gained recent academic interest due to improved high-temperature mechanical properties, by forming coarsening- resistant Al3Sc dispersoids and stabilization of θ′ precipitates. However, gaps in knowledge about the effects of scandium present a challenge to successful commercialization of aluminum-copper-scandium alloys. This work seeks to explore these knowledge gaps and ultimately design and test a commercially feasible aluminum- copper alloy with scandium. To better understand the processing conditions required to avoid the detrimental W-phase (Al8Cu4Sc), castings were produced with a wide range of solidification rates and heat treatments. It was shown that the only feasible heat treatment is a single-step homogenization with copper below 4 wt%, and that higher copper or multi-step homogenization will lead to the formation of W-phase. W-phase results precipitate-free zones which lower the hardness of the resulting microstructure. Using a 3.5 wt% copper sample combined with a single-step homogenization, the effects of scandium in solution on precipitation of copper-rich precipitates are studied. Scandium in solution stabilizes θ″ and θ‴ precipitates over θ′ when aging at 160°C, which is supported by density functional theory calculations that show a significant reduction in the interaction energy of θ″, θ‴, and GP zones with the addition of scandium. Finally, an engineered alloy with low copper and scandium in solution is tested in comparison to AA2219 and is shown to have similar high-temperature strength while having a 60% increase in the fracture toughness. Transmission electron microscopy shows that θ′ precipitates in the scandium-containing alloy have larger aspect ratios and a preference for {100} semi-coherent interfaces. This work expands knowledge of the processing conditions required for a commercially feasible aluminum-copper-scandium alloy and demonstrates an alloy design strategy for this system.","abstract_has_math":false,"creators":["DePottey, Austin M."],"institution":null,"degree_name":"Doctor of Philosophy in Materials Science and Engineering (PhD)","degree_level":"Open Access Dissertation","degree_discipline":"Department of Materials Science and Engineering","degree_department":null,"school":null,"contributors":["Paul Sanders"],"advisors":[],"committee_chairs":[],"committee_members":["Timothy Langan","Stephen Kampe","Walter Milligan"],"year":null,"date_issued":"","date_published":null,"updated_at":"2026-11-19T08:19:20Z","subjects":["Metallurgy"],"languages":[],"rights":[],"rights_urls":[],"identifier_entries":[{"key":"dc:identifier","label":"Identifier","values":["https://digitalcommons.mtu.edu/etdr/1983"],"render_values":[{"text":"https://digitalcommons.mtu.edu/etdr/1983","href":"https://digitalcommons.mtu.edu/etdr/1983","code":true}]}],"person_identifier_entries":[]},"links":{"outbound_url":"https://doi.org/10.37099/mtu.dc.etdr/1983","outbound_label":"DOI","outbound_source":"dc:identifier","record_url":"https://doi.org/10.37099/mtu.dc.etdr/1983","record_label":"Repository record","record_kind":"doi","record_source":"dc:identifier","download_url":null,"download_label":null,"download_source":null,"access_status":null,"embargo_until":null,"access_note":null},"source_record":{"url":"https://digitalcommons.mtu.edu/do/oai/?verb=GetRecord&metadataPrefix=oai_etdms&identifier=oai%3Adigitalcommons.mtu.edu%3Aetdr-3091","prefix":"oai_etdms"},"metadata_groups":[{"id":"people","label":"People","entries":[{"key":"dc:contributor","label":"Contributor","values":["Paul Sanders"]},{"key":"dc:contributor.committeemember","label":"Committee Member","values":["Timothy Langan","Stephen Kampe","Walter Milligan"]},{"key":"dc:creator","label":"Author","values":["DePottey, Austin M."]}]},{"id":"academic_context","label":"Academic Context","entries":[{"key":"dc:date.created","label":"Dc Date Created","values":["2025-01-01T08:00:00Z"]},{"key":"thesis:degree_discipline","label":"Discipline","values":["Department of Materials Science and Engineering"]},{"key":"thesis:degree_level","label":"Degree Level","values":["Open Access Dissertation"]},{"key":"thesis:degree_name","label":"Degree Name","values":["Doctor of Philosophy in Materials Science and Engineering (PhD)"]}]},{"id":"subjects_keywords","label":"Subjects and Keywords","entries":[{"key":"dc:subject","label":"Dc Subject","values":["Metallurgy"]}]},{"id":"identifiers","label":"Identifiers","entries":[{"key":"dc:identifier","label":"Identifier","values":["10.37099/mtu.dc.etdr/1983","https://digitalcommons.mtu.edu/etdr/1983"]}]},{"id":"additional","label":"Additional Metadata","entries":[{"key":"dc:description.abstract","label":"Abstract","values":["The 2xxx series of precipitation-strengthened aluminum-copper alloys are commonly used in high-temperature applications (up to 300°C) where lightweight metals are required. Scandium additions to aluminum-copper alloys have gained recent academic interest due to improved high-temperature mechanical properties, by forming coarsening- resistant Al3Sc dispersoids and stabilization of θ′ precipitates. However, gaps in knowledge about the effects of scandium present a challenge to successful commercialization of aluminum-copper-scandium alloys. This work seeks to explore these knowledge gaps and ultimately design and test a commercially feasible aluminum- copper alloy with scandium. To better understand the processing conditions required to avoid the detrimental W-phase (Al8Cu4Sc), castings were produced with a wide range of solidification rates and heat treatments. It was shown that the only feasible heat treatment is a single-step homogenization with copper below 4 wt%, and that higher copper or multi-step homogenization will lead to the formation of W-phase. W-phase results precipitate-free zones which lower the hardness of the resulting microstructure. Using a 3.5 wt% copper sample combined with a single-step homogenization, the effects of scandium in solution on precipitation of copper-rich precipitates are studied. Scandium in solution stabilizes θ″ and θ‴ precipitates over θ′ when aging at 160°C, which is supported by density functional theory calculations that show a significant reduction in the interaction energy of θ″, θ‴, and GP zones with the addition of scandium. Finally, an engineered alloy with low copper and scandium in solution is tested in comparison to AA2219 and is shown to have similar high-temperature strength while having a 60% increase in the fracture toughness. Transmission electron microscopy shows that θ′ precipitates in the scandium-containing alloy have larger aspect ratios and a preference for {100} semi-coherent interfaces. This work expands knowledge of the processing conditions required for a commercially feasible aluminum-copper-scandium alloy and demonstrates an alloy design strategy for this system."]},{"key":"dc:title","label":"Title","values":["DESIGN OF ALUMINUM-COPPER ALLOY WITH SCANDIUM IN SOLUTION"]}]}],"canonical_facts":{"dc:contributor":["Paul Sanders"],"dc:contributor.committeemember":["Timothy Langan","Stephen Kampe","Walter Milligan"],"dc:creator":["DePottey, Austin M."],"dc:date.created":["2025-01-01T08:00:00Z"],"dc:description.abstract":["The 2xxx series of precipitation-strengthened aluminum-copper alloys are commonly used in high-temperature applications (up to 300°C) where lightweight metals are required. Scandium additions to aluminum-copper alloys have gained recent academic interest due to improved high-temperature mechanical properties, by forming coarsening- resistant Al3Sc dispersoids and stabilization of θ′ precipitates. However, gaps in knowledge about the effects of scandium present a challenge to successful commercialization of aluminum-copper-scandium alloys. This work seeks to explore these knowledge gaps and ultimately design and test a commercially feasible aluminum- copper alloy with scandium. To better understand the processing conditions required to avoid the detrimental W-phase (Al8Cu4Sc), castings were produced with a wide range of solidification rates and heat treatments. It was shown that the only feasible heat treatment is a single-step homogenization with copper below 4 wt%, and that higher copper or multi-step homogenization will lead to the formation of W-phase. W-phase results precipitate-free zones which lower the hardness of the resulting microstructure. Using a 3.5 wt% copper sample combined with a single-step homogenization, the effects of scandium in solution on precipitation of copper-rich precipitates are studied. Scandium in solution stabilizes θ″ and θ‴ precipitates over θ′ when aging at 160°C, which is supported by density functional theory calculations that show a significant reduction in the interaction energy of θ″, θ‴, and GP zones with the addition of scandium. Finally, an engineered alloy with low copper and scandium in solution is tested in comparison to AA2219 and is shown to have similar high-temperature strength while having a 60% increase in the fracture toughness. Transmission electron microscopy shows that θ′ precipitates in the scandium-containing alloy have larger aspect ratios and a preference for {100} semi-coherent interfaces. This work expands knowledge of the processing conditions required for a commercially feasible aluminum-copper-scandium alloy and demonstrates an alloy design strategy for this system."],"dc:identifier":["10.37099/mtu.dc.etdr/1983","https://digitalcommons.mtu.edu/etdr/1983"],"dc:subject":["Metallurgy"],"dc:title":["DESIGN OF ALUMINUM-COPPER ALLOY WITH SCANDIUM IN SOLUTION"],"thesis:degree_discipline":["Department of Materials Science and Engineering"],"thesis:degree_level":["Open Access Dissertation"],"thesis:degree_name":["Doctor of Philosophy in Materials Science and Engineering (PhD)"]},"updated_at":"2026-11-19T08:19:20Z"}