{"id":{"repo_id":"sdstate","oai_identifier":"oai:openprairie.sdstate.edu:etd-2766"},"canonical_url":"https://search.ndltd.org/etd/sdstate/oai:openprairie.sdstate.edu:etd-2766","repository":{"repo_id":"sdstate","name":"South Dakota State University","base_url":"https://openprairie.sdstate.edu/do/oai/"},"display":{"title":"Catalytic Conversion of Biomass to Advanced Bio-Fuels","abstract":"The aim of this work was to produce advanced liquid bio-fuels through thermal conversion of the pine sawdust. Combining an experimental two-stage catalytic pyrolysis system, two rounds of experiments were carried out to investigate the optimal reaction temperature for the HZSM-5 catalyst and the optimal Mo/Cu ratio with regard to Mo- Cu/HZSM-5 catalysts for obtaining qualified bio-fuels. In the first round of experiments, the pine sawdust thermal conversions over HZSM-5 catalysts were performed under different reaction temperatures in the experimental two-stage catalytic pyrolysis system. It was observed that higher temperatures in the catalytic reactor decreased the yield of bio-oil. However, the bio-oil quality was improved. The GC-MS analysis results of the liquid products showed that the pyrolysis reaction at 500 °C and catalytic reaction at 500 °C treatment obtained the highest hydrocarbon content (58.63%) and the highest C8-C12 content (48.03%) in the oil phase. Along with the water content, density, and pH characterization of bio-oils, the pyrolysis reaction at 500 °C and catalytic reaction at 500 °C using HZSM-5 catalyst treatment was further demonstrated as the optimal temperature to achieve low viscosity and higher HHV bio-oils. The XRD characterization indicated that HZSM-5 catalysts had no crystal lattice changes before or after use, which makes HZSM-5 catalyst regeneration possible. In the second round of experiments, Mo-Cu/HZSM-5 catalysts were prepared by an impregnation method. The Mo-Cu/HZSM-5 catalysts and HZSM-5 were characterized xi by Brunauer-Emmett-Teller (BET), X-ray diffraction (XRD) and transmission electron microscopy (TEM). All characterization results indicated that the introduction of CuO is beneficial to the dispersion of MoO3 in the HZSM-5. Combined with the two-stage catalytic pyrolysis system, the Mo-Cu/HZSM-5 catalysts were used for pine sawdust thermal conversion. The products included syngas, bio-oil and bio-char. The syngas was analyzed by gas chromatography (GC). Gas chromatography-mass spectrometry (GC-MS) was used to identify the compounds in bio-oils. The water content, higher heating value (HHV) and viscosity of bio-oils were measured. The HHV and composition of bio-char were determined. The results indicated that Mo (3%)-Cu (3%)/HZSM-5 treatment yielded the highest amount of light hydrocarbons, showed a robust ability to convert methane in the syngas to bio-oil, and displayed no significant difference in the properties of bio-char when compared to different treatments in the same pyrolysis conditions.","abstract_html":"The aim of this work was to produce advanced liquid bio-fuels through thermal conversion of the pine sawdust. Combining an experimental two-stage catalytic pyrolysis system, two rounds of experiments were carried out to investigate the optimal reaction temperature for the HZSM-5 catalyst and the optimal Mo/Cu ratio with regard to Mo- Cu/HZSM-5 catalysts for obtaining qualified bio-fuels. In the first round of experiments, the pine sawdust thermal conversions over HZSM-5 catalysts were performed under different reaction temperatures in the experimental two-stage catalytic pyrolysis system. It was observed that higher temperatures in the catalytic reactor decreased the yield of bio-oil. However, the bio-oil quality was improved. The GC-MS analysis results of the liquid products showed that the pyrolysis reaction at 500 °C and catalytic reaction at 500 °C treatment obtained the highest hydrocarbon content (58.63%) and the highest C8-C12 content (48.03%) in the oil phase. Along with the water content, density, and pH characterization of bio-oils, the pyrolysis reaction at 500 °C and catalytic reaction at 500 °C using HZSM-5 catalyst treatment was further demonstrated as the optimal temperature to achieve low viscosity and higher HHV bio-oils. The XRD characterization indicated that HZSM-5 catalysts had no crystal lattice changes before or after use, which makes HZSM-5 catalyst regeneration possible. In the second round of experiments, Mo-Cu/HZSM-5 catalysts were prepared by an impregnation method. The Mo-Cu/HZSM-5 catalysts and HZSM-5 were characterized xi by Brunauer-Emmett-Teller (BET), X-ray diffraction (XRD) and transmission electron microscopy (TEM). All characterization results indicated that the introduction of CuO is beneficial to the dispersion of MoO3 in the HZSM-5. Combined with the two-stage catalytic pyrolysis system, the Mo-Cu/HZSM-5 catalysts were used for pine sawdust thermal conversion. The products included syngas, bio-oil and bio-char. The syngas was analyzed by gas chromatography (GC). Gas chromatography-mass spectrometry (GC-MS) was used to identify the compounds in bio-oils. The water content, higher heating value (HHV) and viscosity of bio-oils were measured. The HHV and composition of bio-char were determined. The results indicated that Mo (3%)-Cu (3%)/HZSM-5 treatment yielded the highest amount of light hydrocarbons, showed a robust ability to convert methane in the syngas to bio-oil, and displayed no significant difference in the properties of bio-char when compared to different treatments in the same pyrolysis conditions.","abstract_has_math":false,"creators":["Huang, Yinbin"],"institution":null,"degree_name":"Master of Science (MS)","degree_level":"Thesis - University Access Only","degree_discipline":"Agricultural and Biosystems Engineering","degree_department":null,"school":null,"contributors":["Lin Wei"],"advisors":[],"committee_chairs":[],"committee_members":[],"year":null,"date_issued":"","date_published":null,"updated_at":"2026-11-19T08:58:07Z","subjects":["Bioresource and Agricultural Engineering"],"languages":["en"],"rights":[],"rights_urls":["http://rightsstatements.org/vocab/InC/1.0/"],"identifier_entries":[],"person_identifier_entries":[]},"links":{"outbound_url":"https://openprairie.sdstate.edu/etd/1838","outbound_label":"Repository record","outbound_source":"dc:identifier","record_url":"https://openprairie.sdstate.edu/etd/1838","record_label":"Repository record","record_kind":"record","record_source":"dc:identifier","download_url":null,"download_label":null,"download_source":null,"access_status":null,"embargo_until":null,"access_note":null},"source_record":{"url":"https://openprairie.sdstate.edu/do/oai/?verb=GetRecord&metadataPrefix=oai_etdms&identifier=oai%3Aopenprairie.sdstate.edu%3Aetd-2766","prefix":"oai_etdms"},"metadata_groups":[{"id":"people","label":"People","entries":[{"key":"dc:contributor","label":"Contributor","values":["Lin Wei"]},{"key":"dc:creator","label":"Author","values":["Huang, Yinbin"]}]},{"id":"academic_context","label":"Academic Context","entries":[{"key":"dc:date.available","label":"Dc Date Available","values":["2017-09-05T07:00:00Z"]},{"key":"dc:date.created","label":"Dc Date Created","values":["2015-01-01T08:00:00Z"]},{"key":"thesis:degree_discipline","label":"Discipline","values":["Agricultural and Biosystems Engineering"]},{"key":"thesis:degree_level","label":"Degree Level","values":["Thesis - University Access Only"]},{"key":"thesis:degree_name","label":"Degree Name","values":["Master of Science (MS)"]}]},{"id":"subjects_keywords","label":"Subjects and Keywords","entries":[{"key":"dc:subject","label":"Dc Subject","values":["Bioresource and Agricultural Engineering"]}]},{"id":"language_rights","label":"Language and Rights","entries":[{"key":"dc:language","label":"Dc Language","values":["en"]},{"key":"dc:rights","label":"Dc Rights","values":["http://rightsstatements.org/vocab/InC/1.0/"]}]},{"id":"identifiers","label":"Identifiers","entries":[{"key":"dc:identifier","label":"Identifier","values":["https://openprairie.sdstate.edu/etd/1838"]}]},{"id":"additional","label":"Additional Metadata","entries":[{"key":"dc:description.abstract","label":"Abstract","values":["The aim of this work was to produce advanced liquid bio-fuels through thermal conversion of the pine sawdust. Combining an experimental two-stage catalytic pyrolysis system, two rounds of experiments were carried out to investigate the optimal reaction temperature for the HZSM-5 catalyst and the optimal Mo/Cu ratio with regard to Mo- Cu/HZSM-5 catalysts for obtaining qualified bio-fuels. In the first round of experiments, the pine sawdust thermal conversions over HZSM-5 catalysts were performed under different reaction temperatures in the experimental two-stage catalytic pyrolysis system. It was observed that higher temperatures in the catalytic reactor decreased the yield of bio-oil. However, the bio-oil quality was improved. The GC-MS analysis results of the liquid products showed that the pyrolysis reaction at 500 °C and catalytic reaction at 500 °C treatment obtained the highest hydrocarbon content (58.63%) and the highest C8-C12 content (48.03%) in the oil phase. Along with the water content, density, and pH characterization of bio-oils, the pyrolysis reaction at 500 °C and catalytic reaction at 500 °C using HZSM-5 catalyst treatment was further demonstrated as the optimal temperature to achieve low viscosity and higher HHV bio-oils. The XRD characterization indicated that HZSM-5 catalysts had no crystal lattice changes before or after use, which makes HZSM-5 catalyst regeneration possible. In the second round of experiments, Mo-Cu/HZSM-5 catalysts were prepared by an impregnation method. The Mo-Cu/HZSM-5 catalysts and HZSM-5 were characterized xi by Brunauer-Emmett-Teller (BET), X-ray diffraction (XRD) and transmission electron microscopy (TEM). All characterization results indicated that the introduction of CuO is beneficial to the dispersion of MoO3 in the HZSM-5. Combined with the two-stage catalytic pyrolysis system, the Mo-Cu/HZSM-5 catalysts were used for pine sawdust thermal conversion. The products included syngas, bio-oil and bio-char. The syngas was analyzed by gas chromatography (GC). Gas chromatography-mass spectrometry (GC-MS) was used to identify the compounds in bio-oils. The water content, higher heating value (HHV) and viscosity of bio-oils were measured. The HHV and composition of bio-char were determined. The results indicated that Mo (3%)-Cu (3%)/HZSM-5 treatment yielded the highest amount of light hydrocarbons, showed a robust ability to convert methane in the syngas to bio-oil, and displayed no significant difference in the properties of bio-char when compared to different treatments in the same pyrolysis conditions."]},{"key":"dc:title","label":"Title","values":["Catalytic Conversion of Biomass to Advanced Bio-Fuels"]}]}],"canonical_facts":{"dc:contributor":["Lin Wei"],"dc:creator":["Huang, Yinbin"],"dc:date.available":["2017-09-05T07:00:00Z"],"dc:date.created":["2015-01-01T08:00:00Z"],"dc:description.abstract":["The aim of this work was to produce advanced liquid bio-fuels through thermal conversion of the pine sawdust. Combining an experimental two-stage catalytic pyrolysis system, two rounds of experiments were carried out to investigate the optimal reaction temperature for the HZSM-5 catalyst and the optimal Mo/Cu ratio with regard to Mo- Cu/HZSM-5 catalysts for obtaining qualified bio-fuels. In the first round of experiments, the pine sawdust thermal conversions over HZSM-5 catalysts were performed under different reaction temperatures in the experimental two-stage catalytic pyrolysis system. It was observed that higher temperatures in the catalytic reactor decreased the yield of bio-oil. However, the bio-oil quality was improved. The GC-MS analysis results of the liquid products showed that the pyrolysis reaction at 500 °C and catalytic reaction at 500 °C treatment obtained the highest hydrocarbon content (58.63%) and the highest C8-C12 content (48.03%) in the oil phase. Along with the water content, density, and pH characterization of bio-oils, the pyrolysis reaction at 500 °C and catalytic reaction at 500 °C using HZSM-5 catalyst treatment was further demonstrated as the optimal temperature to achieve low viscosity and higher HHV bio-oils. The XRD characterization indicated that HZSM-5 catalysts had no crystal lattice changes before or after use, which makes HZSM-5 catalyst regeneration possible. In the second round of experiments, Mo-Cu/HZSM-5 catalysts were prepared by an impregnation method. The Mo-Cu/HZSM-5 catalysts and HZSM-5 were characterized xi by Brunauer-Emmett-Teller (BET), X-ray diffraction (XRD) and transmission electron microscopy (TEM). All characterization results indicated that the introduction of CuO is beneficial to the dispersion of MoO3 in the HZSM-5. Combined with the two-stage catalytic pyrolysis system, the Mo-Cu/HZSM-5 catalysts were used for pine sawdust thermal conversion. The products included syngas, bio-oil and bio-char. The syngas was analyzed by gas chromatography (GC). Gas chromatography-mass spectrometry (GC-MS) was used to identify the compounds in bio-oils. The water content, higher heating value (HHV) and viscosity of bio-oils were measured. The HHV and composition of bio-char were determined. The results indicated that Mo (3%)-Cu (3%)/HZSM-5 treatment yielded the highest amount of light hydrocarbons, showed a robust ability to convert methane in the syngas to bio-oil, and displayed no significant difference in the properties of bio-char when compared to different treatments in the same pyrolysis conditions."],"dc:identifier":["https://openprairie.sdstate.edu/etd/1838"],"dc:language":["en"],"dc:rights":["http://rightsstatements.org/vocab/InC/1.0/"],"dc:subject":["Bioresource and Agricultural Engineering"],"dc:title":["Catalytic Conversion of Biomass to Advanced Bio-Fuels"],"thesis:degree_discipline":["Agricultural and Biosystems Engineering"],"thesis:degree_level":["Thesis - University Access Only"],"thesis:degree_name":["Master of Science (MS)"]},"updated_at":"2026-11-19T08:58:07Z"}