{"id":{"repo_id":"usf","oai_identifier":"oai:digitalcommons.usf.edu:etd-3066"},"canonical_url":"https://search.ndltd.org/etd/usf/oai:digitalcommons.usf.edu:etd-3066","repository":{"repo_id":"usf","name":"University of South Florida","base_url":"https://digitalcommons.usf.edu/do/oai/"},"display":{"title":"Growth of 3C-SiC on (111)Si using Hot-Wall Chemical Vapor Deposition","abstract":"The heteroepitaxial growth of cubic silicon carbide (3C-SiC) on (111) silicon (Si) substrates, via a horizontal hot-wall chemical vapor deposition (CVD) reactor, has been achieved. Growth was conducted using a two step process: first the Si substrate surface is converted to SiC via a carbonization process and second the growth of 3C-SiC is performed on the initial carbonized layer. During carbonization, the surface of the Si is converted to 3C-SiC, which helps to minimize the stress in the growing crystal. Propane (C3H8) and silane (SiH4), diluted in hydrogen (H2), were used as the carbon and silicon source, respectively. A deposition rate of approximately 10 µm/h was established during the initial process at a temperature of ~1380 °C. The optimized process produced films with X-ray rocking curve full-width at half-maximum (FWHM) values of 219 arcsec, which is significantly better than any other published results in the literature. Once this process was developed a lower temperature process was developed at a slower growth rate of ~2 µm/h at 1225 °C. The crystal quality was inferior at the reduced temperature but this new process allows for the growth of 3C-SiC(111) films on oxide release layers for MEMS applications. In addition, for electronic device applications, a lower temperature process reduces the generation of defects caused by the nearly 8 % mismatch in the coefficient of thermal expansion (CTE) between 3C-SiC and Si. Finally a new process using a poly-Si seed layer deposited on an oxide-coated Si wafer was used to form 3C-SiC films for MEMS applications. The results indicated initially that the films may even be monocrystalline (based on X-ray evaluation) but later analysis performed using TEM indicated they were highly-ordered polycrystalline films. The grown 3C-SiC films were analyzed using a variety of characterization techniques. The thickness of the films was assessed through Fourier Transform infrared (FTIR) spectroscopy, and confirmed (in the case of growth on poly-Si seed layers) by cross-section scanning electron microscopy (SEM). The SEM cross-sections were also used to investigate the 3C-SiC/oxide interface. The surface morphology of the films was inspected via Nomarsky interference optical microscopy, atomic force microscopy (AFM), and SEM. The crystalline quality of the films was determined through X-ray diffraction (XRD).","abstract_html":"The heteroepitaxial growth of cubic silicon carbide (3C-SiC) on (111) silicon (Si) substrates, via a horizontal hot-wall chemical vapor deposition (CVD) reactor, has been achieved. Growth was conducted using a two step process: first the Si substrate surface is converted to SiC via a carbonization process and second the growth of 3C-SiC is performed on the initial carbonized layer. During carbonization, the surface of the Si is converted to 3C-SiC, which helps to minimize the stress in the growing crystal. Propane (C3H8) and silane (SiH4), diluted in hydrogen (H2), were used as the carbon and silicon source, respectively. A deposition rate of approximately 10 µm/h was established during the initial process at a temperature of ~1380 °C. The optimized process produced films with X-ray rocking curve full-width at half-maximum (FWHM) values of 219 arcsec, which is significantly better than any other published results in the literature. Once this process was developed a lower temperature process was developed at a slower growth rate of ~2 µm/h at 1225 °C. The crystal quality was inferior at the reduced temperature but this new process allows for the growth of 3C-SiC(111) films on oxide release layers for MEMS applications. In addition, for electronic device applications, a lower temperature process reduces the generation of defects caused by the nearly 8 % mismatch in the coefficient of thermal expansion (CTE) between 3C-SiC and Si. Finally a new process using a poly-Si seed layer deposited on an oxide-coated Si wafer was used to form 3C-SiC films for MEMS applications. The results indicated initially that the films may even be monocrystalline (based on X-ray evaluation) but later analysis performed using TEM indicated they were highly-ordered polycrystalline films. The grown 3C-SiC films were analyzed using a variety of characterization techniques. The thickness of the films was assessed through Fourier Transform infrared (FTIR) spectroscopy, and confirmed (in the case of growth on poly-Si seed layers) by cross-section scanning electron microscopy (SEM). The SEM cross-sections were also used to investigate the 3C-SiC/oxide interface. The surface morphology of the films was inspected via Nomarsky interference optical microscopy, atomic force microscopy (AFM), and SEM. The crystalline quality of the films was determined through X-ray diffraction (XRD).","abstract_has_math":false,"creators":["Locke, Christopher"],"institution":"University of South Florida","degree_name":null,"degree_level":"Thesis","degree_discipline":"Electrical Engineering","degree_department":null,"school":null,"contributors":["Stephen E. Saddow, Ph.D.","Andrew M. Hoff, Ph.D.","Priscila Spagnol, Ph.D.","Francesco La Via, Ph.D."],"advisors":[],"committee_chairs":[],"committee_members":[],"year":2009,"date_issued":"2009-01-01T08:00:00Z","date_published":"2009-01-01T08:00:00Z","updated_at":"2026-11-19T08:34:29Z","subjects":["silicon carbide","heteroepitaxy","crystal defects","chemical vapor deposition","polysilicon","American Studies","Arts and Humanities"],"languages":["EN-US"],"rights":[],"rights_urls":[],"identifier_entries":[],"person_identifier_entries":[]},"links":{"outbound_url":"https://digitalcommons.usf.edu/etd/2067","outbound_label":"Repository record","outbound_source":"dc:identifier","record_url":"https://digitalcommons.usf.edu/etd/2067","record_label":"Repository record","record_kind":"record","record_source":"dc:identifier","download_url":null,"download_label":null,"download_source":null,"access_status":null,"embargo_until":null,"access_note":null},"source_record":{"url":"https://digitalcommons.usf.edu/do/oai/?verb=GetRecord&metadataPrefix=oai_etdms&identifier=oai%3Adigitalcommons.usf.edu%3Aetd-3066","prefix":"oai_etdms"},"metadata_groups":[{"id":"people","label":"People","entries":[{"key":"dc:contributor","label":"Contributor","values":["Stephen E. Saddow, Ph.D.","Andrew M. Hoff, Ph.D.","Priscila Spagnol, Ph.D.","Francesco La Via, Ph.D."]},{"key":"dc:creator","label":"Author","values":["Locke, Christopher"]}]},{"id":"academic_context","label":"Academic Context","entries":[{"key":"dc:date","label":"Dc Date","values":["2009-01-01T08:00:00Z"]},{"key":"thesis:degree_discipline","label":"Discipline","values":["Electrical Engineering"]},{"key":"thesis:degree_level","label":"Degree Level","values":["Thesis","M.S.E.E."]},{"key":"thesis:institution_name","label":"Thesis Institution Name","values":["University of South Florida"]}]},{"id":"subjects_keywords","label":"Subjects and Keywords","entries":[{"key":"dc:subject","label":"Dc Subject","values":["silicon carbide","heteroepitaxy","crystal defects","chemical vapor deposition","polysilicon","American Studies","Arts and Humanities"]}]},{"id":"language_rights","label":"Language and Rights","entries":[{"key":"dc:language","label":"Dc Language","values":["EN-US"]},{"key":"dc:rights.license","label":"Dc Rights License","values":["default"]}]},{"id":"identifiers","label":"Identifiers","entries":[{"key":"dc:identifier","label":"Identifier","values":["https://digitalcommons.usf.edu/etd/2067"]}]},{"id":"additional","label":"Additional Metadata","entries":[{"key":"dc:description","label":"Description","values":["The heteroepitaxial growth of cubic silicon carbide (3C-SiC) on (111) silicon (Si) substrates, via a horizontal hot-wall chemical vapor deposition (CVD) reactor, has been achieved. Growth was conducted using a two step process: first the Si substrate surface is converted to SiC via a carbonization process and second the growth of 3C-SiC is performed on the initial carbonized layer. During carbonization, the surface of the Si is converted to 3C-SiC, which helps to minimize the stress in the growing crystal. Propane (C3H8) and silane (SiH4), diluted in hydrogen (H2), were used as the carbon and silicon source, respectively. A deposition rate of approximately 10 µm/h was established during the initial process at a temperature of ~1380 °C. The optimized process produced films with X-ray rocking curve full-width at half-maximum (FWHM) values of 219 arcsec, which is significantly better than any other published results in the literature. Once this process was developed a lower temperature process was developed at a slower growth rate of ~2 µm/h at 1225 °C. The crystal quality was inferior at the reduced temperature but this new process allows for the growth of 3C-SiC(111) films on oxide release layers for MEMS applications. In addition, for electronic device applications, a lower temperature process reduces the generation of defects caused by the nearly 8 % mismatch in the coefficient of thermal expansion (CTE) between 3C-SiC and Si. Finally a new process using a poly-Si seed layer deposited on an oxide-coated Si wafer was used to form 3C-SiC films for MEMS applications. The results indicated initially that the films may even be monocrystalline (based on X-ray evaluation) but later analysis performed using TEM indicated they were highly-ordered polycrystalline films. The grown 3C-SiC films were analyzed using a variety of characterization techniques. The thickness of the films was assessed through Fourier Transform infrared (FTIR) spectroscopy, and confirmed (in the case of growth on poly-Si seed layers) by cross-section scanning electron microscopy (SEM). The SEM cross-sections were also used to investigate the 3C-SiC/oxide interface. The surface morphology of the films was inspected via Nomarsky interference optical microscopy, atomic force microscopy (AFM), and SEM. The crystalline quality of the films was determined through X-ray diffraction (XRD)."]},{"key":"dc:title","label":"Title","values":["Growth of 3C-SiC on (111)Si using Hot-Wall Chemical Vapor Deposition"]}]}],"canonical_facts":{"dc:contributor":["Stephen E. Saddow, Ph.D.","Andrew M. Hoff, Ph.D.","Priscila Spagnol, Ph.D.","Francesco La Via, Ph.D."],"dc:creator":["Locke, Christopher"],"dc:date":["2009-01-01T08:00:00Z"],"dc:description":["The heteroepitaxial growth of cubic silicon carbide (3C-SiC) on (111) silicon (Si) substrates, via a horizontal hot-wall chemical vapor deposition (CVD) reactor, has been achieved. Growth was conducted using a two step process: first the Si substrate surface is converted to SiC via a carbonization process and second the growth of 3C-SiC is performed on the initial carbonized layer. During carbonization, the surface of the Si is converted to 3C-SiC, which helps to minimize the stress in the growing crystal. Propane (C3H8) and silane (SiH4), diluted in hydrogen (H2), were used as the carbon and silicon source, respectively. A deposition rate of approximately 10 µm/h was established during the initial process at a temperature of ~1380 °C. The optimized process produced films with X-ray rocking curve full-width at half-maximum (FWHM) values of 219 arcsec, which is significantly better than any other published results in the literature. Once this process was developed a lower temperature process was developed at a slower growth rate of ~2 µm/h at 1225 °C. The crystal quality was inferior at the reduced temperature but this new process allows for the growth of 3C-SiC(111) films on oxide release layers for MEMS applications. In addition, for electronic device applications, a lower temperature process reduces the generation of defects caused by the nearly 8 % mismatch in the coefficient of thermal expansion (CTE) between 3C-SiC and Si. Finally a new process using a poly-Si seed layer deposited on an oxide-coated Si wafer was used to form 3C-SiC films for MEMS applications. The results indicated initially that the films may even be monocrystalline (based on X-ray evaluation) but later analysis performed using TEM indicated they were highly-ordered polycrystalline films. The grown 3C-SiC films were analyzed using a variety of characterization techniques. The thickness of the films was assessed through Fourier Transform infrared (FTIR) spectroscopy, and confirmed (in the case of growth on poly-Si seed layers) by cross-section scanning electron microscopy (SEM). The SEM cross-sections were also used to investigate the 3C-SiC/oxide interface. The surface morphology of the films was inspected via Nomarsky interference optical microscopy, atomic force microscopy (AFM), and SEM. The crystalline quality of the films was determined through X-ray diffraction (XRD)."],"dc:identifier":["https://digitalcommons.usf.edu/etd/2067"],"dc:language":["EN-US"],"dc:rights.license":["default"],"dc:subject":["silicon carbide","heteroepitaxy","crystal defects","chemical vapor deposition","polysilicon","American Studies","Arts and Humanities"],"dc:title":["Growth of 3C-SiC on (111)Si using Hot-Wall Chemical Vapor Deposition"],"thesis:degree_discipline":["Electrical Engineering"],"thesis:degree_level":["Thesis","M.S.E.E."],"thesis:institution_name":["University of South Florida"]},"updated_at":"2026-11-19T08:34:29Z"}