{"id":{"repo_id":"vt","oai_identifier":"oai:vtechworks.lib.vt.edu:10919/45006"},"canonical_url":"https://search.ndltd.org/etd/vt/oai:vtechworks.lib.vt.edu:10919/45006","repository":{"repo_id":"vt","name":"Virginia Tech","base_url":"https://vtechworks.lib.vt.edu/oai/request"},"display":{"title":"Design of, and initial experiments with, a MIMO plate control testbed","abstract":"This work discusses the design of, and initial experiments with, a MIMO plate control testbed. This structure will be used as a development and standard comparison site for AVC and ASAC and is an extension of previous SIMO control investigations which used accelerometers and shakers. This portion of the development process of the MIMO plate control testbed is concerned with actuator and sensor materials and architecture, modeling approaches and requirements, and initial control experiments. The piezoelectric sensors and actuators are arranged on the plate to control the first five vibration modes. The sensors measure plate positions using a high impedance signal conditioning amplifier. The sixteen-channel design implements a band-pass filter to eliminate low- and high-frequency noise. The power amplification scheme chosen for the actuators uses low-gain amplifiers (~2.5 V/V) in series with a transformer (24:1) to deliver high voltages (up to 150 V) to the actuators. Low-pass smoothing filters (200 Hz cutoff) were added on the control inputs to reduce the high frequency content of the zero-order-held digital control signal. Initial methods for system identification of piezostructures are presented. Parametric frequency response approaches (modal analysis) were used and the model achieved is compared with measured data and purely analytic models. The empirical model was used in initial SIMO control experiments to demonstrate the testbed closed-loop performance. A LQG controller was implemented and produced 6 dB of suppression for the second mode for a 110 Hz disturbance.","abstract_html":"This work discusses the design of, and initial experiments with, a MIMO plate control testbed. This structure will be used as a development and standard comparison site for AVC and ASAC and is an extension of previous SIMO control investigations which used accelerometers and shakers. This portion of the development process of the MIMO plate control testbed is concerned with actuator and sensor materials and architecture, modeling approaches and requirements, and initial control experiments. The piezoelectric sensors and actuators are arranged on the plate to control the first five vibration modes. The sensors measure plate positions using a high impedance signal conditioning amplifier. The sixteen-channel design implements a band-pass filter to eliminate low- and high-frequency noise. The power amplification scheme chosen for the actuators uses low-gain amplifiers (~2.5 V/V) in series with a transformer (24:1) to deliver high voltages (up to 150 V) to the actuators. Low-pass smoothing filters (200 Hz cutoff) were added on the control inputs to reduce the high frequency content of the zero-order-held digital control signal. Initial methods for system identification of piezostructures are presented. Parametric frequency response approaches (modal analysis) were used and the model achieved is compared with measured data and purely analytic models. The empirical model was used in initial SIMO control experiments to demonstrate the testbed closed-loop performance. A LQG controller was implemented and produced 6 dB of suppression for the second mode for a 110 Hz disturbance.","abstract_has_math":false,"creators":["Cole, Daniel G."],"institution":"Virginia Tech","degree_name":"Master of Science","degree_level":"masters","degree_discipline":"Mechanical Engineering","degree_department":"Mechanical Engineering","school":null,"contributors":[],"advisors":[],"committee_chairs":["Robertshaw, Harry H."],"committee_members":["Baumann, William T.","Cudney, Harley H."],"year":1992,"date_issued":"1992-09-01","date_published":"1992-09-01","updated_at":"2026-11-18T20:14:55Z","subjects":["Actuators","Detectors"],"languages":["en"],"rights":["In Copyright"],"rights_urls":["http://rightsstatements.org/vocab/InC/1.0/"],"identifier_entries":[{"key":"dc:identifier.other","label":"Dc Identifier Other","values":["etd-10062009-020045"],"render_values":[{"text":"etd-10062009-020045","href":null,"code":true}]},{"key":"dc:identifier.sourceurl","label":"Source URL","values":["http://scholar.lib.vt.edu/theses/available/etd-10062009-020045/"],"render_values":[{"text":"http://scholar.lib.vt.edu/theses/available/etd-10062009-020045/","href":"http://scholar.lib.vt.edu/theses/available/etd-10062009-020045/","code":true}]}],"person_identifier_entries":[]},"links":{"outbound_url":"http://hdl.handle.net/10919/45006","outbound_label":"Handle","outbound_source":"dc:identifier.uri","record_url":"http://hdl.handle.net/10919/45006","record_label":"Repository record","record_kind":"handle","record_source":"dc:identifier.uri","download_url":null,"download_label":null,"download_source":null,"access_status":null,"embargo_until":null,"access_note":null},"source_record":{"url":"https://vtechworks.lib.vt.edu/oai/request?verb=GetRecord&metadataPrefix=dim&identifier=oai%3Avtechworks.lib.vt.edu%3A10919%2F45006","prefix":"dim"},"metadata_groups":[{"id":"people","label":"People","entries":[{"key":"dc:contributor.committeechair","label":"Committee Chair","values":["Robertshaw, Harry H."]},{"key":"dc:contributor.committeemember","label":"Committee Member","values":["Baumann, William T.","Cudney, Harley H."]},{"key":"dc:contributor.department","label":"Department","values":["Mechanical Engineering"]},{"key":"dc:creator","label":"Author","values":["Cole, Daniel G."]}]},{"id":"academic_context","label":"Academic Context","entries":[{"key":"dc:date.accepted","label":"Dc Date Accepted","values":["2009-10-06"]},{"key":"dc:date.accessioned","label":"Dc Date Accessioned","values":["2014-03-14T21:46:52Z"]},{"key":"dc:date.available","label":"Dc Date Available","values":["2014-03-14T21:46:52Z","2009-10-06"]},{"key":"dc:date.issued","label":"Date","values":["1992-09-01"]},{"key":"dc:date.submitted","label":"Dc Date Submitted","values":["2009-10-06"]},{"key":"dc:publisher","label":"Institution","values":["Virginia Tech"]},{"key":"dc:relation.haspart","label":"Dc Relation Haspart","values":["LD5655.V855_1992.C65.pdf"]},{"key":"dc:relation.isformatof","label":"Dc Relation Isformatof","values":["OCLC# 27371169"]},{"key":"dc:type","label":"Dc Type","values":["Thesis"]},{"key":"dc:type.dcmitype","label":"Dc Type Dcmitype","values":["Text"]},{"key":"thesis:degree_discipline","label":"Discipline","values":["Mechanical Engineering"]},{"key":"thesis:degree_level","label":"Degree Level","values":["masters"]},{"key":"thesis:degree_name","label":"Degree Name","values":["Master of Science"]},{"key":"thesis:institution_name","label":"Thesis Institution Name","values":["Virginia Polytechnic Institute and State University"]}]},{"id":"subjects_keywords","label":"Subjects and Keywords","entries":[{"key":"dc:subject.lcc","label":"Dc Subject Lcc","values":["LD5655.V855 1992.C65"]},{"key":"dc:subject.lcsh","label":"Dc Subject Lcsh","values":["Actuators","Detectors"]}]},{"id":"language_rights","label":"Language and Rights","entries":[{"key":"dc:language.iso","label":"Language (ISO)","values":["en"]},{"key":"dc:rights","label":"Dc Rights","values":["In Copyright"]},{"key":"dc:rights.uri","label":"Rights URI","values":["http://rightsstatements.org/vocab/InC/1.0/"]}]},{"id":"identifiers","label":"Identifiers","entries":[{"key":"dc:identifier.other","label":"Dc Identifier Other","values":["etd-10062009-020045"]},{"key":"dc:identifier.sourceurl","label":"Source URL","values":["http://scholar.lib.vt.edu/theses/available/etd-10062009-020045/"]},{"key":"dc:identifier.uri","label":"Identifier URI","values":["http://hdl.handle.net/10919/45006"]}]},{"id":"additional","label":"Additional Metadata","entries":[{"key":"dc:description.abstract","label":"Abstract","values":["This work discusses the design of, and initial experiments with, a MIMO plate control testbed. This structure will be used as a development and standard comparison site for AVC and ASAC and is an extension of previous SIMO control investigations which used accelerometers and shakers. This portion of the development process of the MIMO plate control testbed is concerned with actuator and sensor materials and architecture, modeling approaches and requirements, and initial control experiments. The piezoelectric sensors and actuators are arranged on the plate to control the first five vibration modes. The sensors measure plate positions using a high impedance signal conditioning amplifier. The sixteen-channel design implements a band-pass filter to eliminate low- and high-frequency noise. The power amplification scheme chosen for the actuators uses low-gain amplifiers (~2.5 V/V) in series with a transformer (24:1) to deliver high voltages (up to 150 V) to the actuators. Low-pass smoothing filters (200 Hz cutoff) were added on the control inputs to reduce the high frequency content of the zero-order-held digital control signal. Initial methods for system identification of piezostructures are presented. Parametric frequency response approaches (modal analysis) were used and the model achieved is compared with measured data and purely analytic models. The empirical model was used in initial SIMO control experiments to demonstrate the testbed closed-loop performance. A LQG controller was implemented and produced 6 dB of suppression for the second mode for a 110 Hz disturbance."]},{"key":"dc:description.degree","label":"Dc Description Degree","values":["Master of Science"]},{"key":"dc:format.extent","label":"Dc Format Extent","values":["viii, 51 leaves"]},{"key":"dc:format.medium","label":"Dc Format Medium","values":["BTD"]},{"key":"dc:format.mimetype","label":"Dc Format Mimetype","values":["application/pdf"]},{"key":"dc:title","label":"Title","values":["Design of, and initial experiments with, a MIMO plate control testbed"]}]}],"canonical_facts":{"dc:contributor.committeechair":["Robertshaw, Harry H."],"dc:contributor.committeemember":["Baumann, William T.","Cudney, Harley H."],"dc:contributor.department":["Mechanical Engineering"],"dc:creator":["Cole, Daniel G."],"dc:date.accepted":["2009-10-06"],"dc:date.accessioned":["2014-03-14T21:46:52Z"],"dc:date.available":["2014-03-14T21:46:52Z","2009-10-06"],"dc:date.issued":["1992-09-01"],"dc:date.submitted":["2009-10-06"],"dc:description.abstract":["This work discusses the design of, and initial experiments with, a MIMO plate control testbed. This structure will be used as a development and standard comparison site for AVC and ASAC and is an extension of previous SIMO control investigations which used accelerometers and shakers. This portion of the development process of the MIMO plate control testbed is concerned with actuator and sensor materials and architecture, modeling approaches and requirements, and initial control experiments. The piezoelectric sensors and actuators are arranged on the plate to control the first five vibration modes. The sensors measure plate positions using a high impedance signal conditioning amplifier. The sixteen-channel design implements a band-pass filter to eliminate low- and high-frequency noise. The power amplification scheme chosen for the actuators uses low-gain amplifiers (~2.5 V/V) in series with a transformer (24:1) to deliver high voltages (up to 150 V) to the actuators. Low-pass smoothing filters (200 Hz cutoff) were added on the control inputs to reduce the high frequency content of the zero-order-held digital control signal. Initial methods for system identification of piezostructures are presented. Parametric frequency response approaches (modal analysis) were used and the model achieved is compared with measured data and purely analytic models. The empirical model was used in initial SIMO control experiments to demonstrate the testbed closed-loop performance. A LQG controller was implemented and produced 6 dB of suppression for the second mode for a 110 Hz disturbance."],"dc:description.degree":["Master of Science"],"dc:format.extent":["viii, 51 leaves"],"dc:format.medium":["BTD"],"dc:format.mimetype":["application/pdf"],"dc:identifier.other":["etd-10062009-020045"],"dc:identifier.sourceurl":["http://scholar.lib.vt.edu/theses/available/etd-10062009-020045/"],"dc:identifier.uri":["http://hdl.handle.net/10919/45006"],"dc:language.iso":["en"],"dc:publisher":["Virginia Tech"],"dc:relation.haspart":["LD5655.V855_1992.C65.pdf"],"dc:relation.isformatof":["OCLC# 27371169"],"dc:rights":["In Copyright"],"dc:rights.uri":["http://rightsstatements.org/vocab/InC/1.0/"],"dc:subject.lcc":["LD5655.V855 1992.C65"],"dc:subject.lcsh":["Actuators","Detectors"],"dc:title":["Design of, and initial experiments with, a MIMO plate control testbed"],"dc:type":["Thesis"],"dc:type.dcmitype":["Text"],"thesis:degree_discipline":["Mechanical Engineering"],"thesis:degree_level":["masters"],"thesis:degree_name":["Master of Science"],"thesis:institution_name":["Virginia Polytechnic Institute and State University"]},"updated_at":"2026-11-18T20:14:55Z"}