{"id":{"repo_id":"whiterose","oai_identifier":"oai:etheses.whiterose.ac.uk:29246"},"canonical_url":"https://search.ndltd.org/etd/whiterose/oai:etheses.whiterose.ac.uk:29246","repository":{"repo_id":"whiterose","name":"White Rose University Consortium","base_url":"https://etheses.whiterose.ac.uk/cgi/oai2"},"display":{"title":"Evaluating the Machinability of Titanium Alloys, Timetal 407 and Ti-6Al-4V","abstract":"An industry focussed research project has been undertaken to evaluate the machinability of an emerging titanium alloy, Timetal 407 and offer a fundamental understanding for the chip control issues. This research identified two key stages in the life cycle of a titanium alloy where consideration of the machinability would provide economic opportunities for the aerospace manufacturing sector. First in the development of emerging alloys and secondly in optimising the cutting parameters during the machining of aerospace components. To assess machinability in the developmental stage of an emerging alloy, a series of small scale experiments were utilised to assess the machinability outputs for Timetal 407 and Ti-6Al-4V, with the aim of drawing conclusions about each of the alloys limitations and strengths in regards to key machinability characteristics; tool wear, chip control, subsurface deformation and cutting forces. The key to these tests was to remain low cost, offering a quick turnaround of results relative to high speed machining, in order to filter out a large number of alloy chemistries and microstructural combinations. For the second stage, machinability maps for Timetal 407 and Ti-6Al-4V were developed using data from high speed machining operations which determined for a range of cutting parameters (cutting speed and feed rate) where machinability outputs were acceptable and Material Removal Rate (MRR) was maximised. The machinability map again incorporated the key machinability characteristics: tool wear, chip control and subsurface deformation as primary points of consideration on the map, with cutting force as a secondary consideration. The map also identified a region of cutting parameters where improved chip management of Timetal 407 could be achieved. Using the high speed machining and small scale machinability experiments, mechanical twins and thermoplastic instability were identified as key determinants for chip control. The outcomes of this research were an ability to characterise machinability using a small scale experimental framework, as well as fulfilling the industry requirements through improving chip management. The improvement of chip management had a number of concurrent benefits to manufacturing operations of large structural gas turbine engine components through reducing cutting time by 43% between Ti-6Al-4V and Timetal 407, whilst also reducing cleaning downtime between parts and reducing machine maintenance to fix issues with chip swarf conveyors. The risk of component rework due to tool breakage or surface finish defects have been reduced, offering potential savings of 300 minutes per part for ‘on machine’ rework, or 480 minutes per part for ‘hand dressing’ by an operator. Due to these operational improvements, the flow of parts through manufacturing facilities has been improved, reducing inventory stock and work in progress.","abstract_html":"An industry focussed research project has been undertaken to evaluate the machinability of an emerging titanium alloy, Timetal 407 and offer a fundamental understanding for the chip control issues. This research identified two key stages in the life cycle of a titanium alloy where consideration of the machinability would provide economic opportunities for the aerospace manufacturing sector. First in the development of emerging alloys and secondly in optimising the cutting parameters during the machining of aerospace components. To assess machinability in the developmental stage of an emerging alloy, a series of small scale experiments were utilised to assess the machinability outputs for Timetal 407 and Ti-6Al-4V, with the aim of drawing conclusions about each of the alloys limitations and strengths in regards to key machinability characteristics; tool wear, chip control, subsurface deformation and cutting forces. The key to these tests was to remain low cost, offering a quick turnaround of results relative to high speed machining, in order to filter out a large number of alloy chemistries and microstructural combinations. For the second stage, machinability maps for Timetal 407 and Ti-6Al-4V were developed using data from high speed machining operations which determined for a range of cutting parameters (cutting speed and feed rate) where machinability outputs were acceptable and Material Removal Rate (MRR) was maximised. The machinability map again incorporated the key machinability characteristics: tool wear, chip control and subsurface deformation as primary points of consideration on the map, with cutting force as a secondary consideration. The map also identified a region of cutting parameters where improved chip management of Timetal 407 could be achieved. Using the high speed machining and small scale machinability experiments, mechanical twins and thermoplastic instability were identified as key determinants for chip control. The outcomes of this research were an ability to characterise machinability using a small scale experimental framework, as well as fulfilling the industry requirements through improving chip management. The improvement of chip management had a number of concurrent benefits to manufacturing operations of large structural gas turbine engine components through reducing cutting time by 43% between Ti-6Al-4V and Timetal 407, whilst also reducing cleaning downtime between parts and reducing machine maintenance to fix issues with chip swarf conveyors. The risk of component rework due to tool breakage or surface finish defects have been reduced, offering potential savings of 300 minutes per part for ‘on machine’ rework, or 480 minutes per part for ‘hand dressing’ by an operator. Due to these operational improvements, the flow of parts through manufacturing facilities has been improved, reducing inventory stock and work in progress.","abstract_has_math":false,"creators":["Dredge, Christopher"],"institution":"University of Sheffield","degree_name":"Eng.D","degree_level":"doctoral","degree_discipline":null,"degree_department":null,"school":null,"contributors":[],"advisors":["Jackson, Martin"],"committee_chairs":[],"committee_members":[],"year":2021,"date_issued":"2021-01","date_published":"2021-01","updated_at":"2026-11-18T22:43:01Z","subjects":[],"languages":["eng"],"rights":[],"rights_urls":[],"identifier_entries":[{"key":"dc:identifier","label":"Identifier","values":["uk.bl.ethos.834115"],"render_values":[{"text":"uk.bl.ethos.834115","href":null,"code":true}]},{"key":"dc:identifier.grantnumber","label":"Dc Identifier Grantnumber","values":["EP/L016257/1"],"render_values":[{"text":"EP/L016257/1","href":null,"code":true}]}],"person_identifier_entries":[{"key":"person:identifier.orcid","label":"ORCID","values":["000000029479343X"],"render_values":[{"text":"0000-0002-9479-343X","href":"https://orcid.org/0000-0002-9479-343X","code":true}]}]},"links":{"outbound_url":null,"outbound_label":null,"outbound_source":null,"record_url":null,"record_label":null,"record_kind":null,"record_source":null,"download_url":"https://etheses.whiterose.ac.uk/id/eprint/29246/1/Thesis_Chap0-6.0_v8.pdf","download_label":"Download PDF","download_source":"dc:identifier.uri","access_status":null,"embargo_until":null,"access_note":null},"source_record":{"url":"https://etheses.whiterose.ac.uk/cgi/oai2?verb=GetRecord&metadataPrefix=uketd_dc&identifier=oai%3Aetheses.whiterose.ac.uk%3A29246","prefix":"uketd_dc"},"metadata_groups":[{"id":"people","label":"People","entries":[{"key":"dc:contributor.advisor","label":"Advisor","values":["Jackson, Martin"]},{"key":"dc:contributor.sponsor","label":"Sponsor","values":["EPSRC"]},{"key":"dc:creator","label":"Author","values":["Dredge, Christopher"]},{"key":"person:identifier.orcid","label":"ORCID","values":["000000029479343X"]}]},{"id":"academic_context","label":"Academic Context","entries":[{"key":"dc:date","label":"Dc Date","values":["2021-01"]},{"key":"dc:date.issued","label":"Date","values":["2021-01"]},{"key":"dc:publisher.department","label":"Dc Publisher Department","values":["Materials Science and Engineering (Sheffield)"]},{"key":"dc:publisher.institution","label":"Dc Publisher Institution","values":["University of Sheffield"]},{"key":"dc:relation.isreferencedby","label":"Dc Relation Isreferencedby","values":["https://etheses.whiterose.ac.uk/id/eprint/29246/"]},{"key":"dc:relation.references","label":"Dc Relation References","values":["1 C. Leyens and M. Peters, Titanium and Titanium Alloys. Wiley-VCH, 2003. 2 D. Rugg, M. Dixon, and F. P. E. Dunne, “Effective structural unit size in titanium alloys,” J. Strain Anal. Eng. Des., vol. 42, no. 4, pp. 269–279, May 2007. 3 A. A. Salem, S. R. Kalidindi, and R. D. Doherty, “Strain hardening of titanium: role of deformation twinning,” Acta Mater., vol. 51, no. 14, pp. 4225–4237, Aug. 2003. 4 A. A. Salem, S. R. Kalidindi, and R. D. Doherty, “Strain hardening regimes and microstructure evolution during large strain compression of high purity titanium,” Scr. Mater., vol. 46, no. 6, pp. 419–423, 2002. 5 A. Chapuis and J. H. Driver, “Temperature dependency of slip and twinning in plane strain compressed magnesium single crystals,” Acta Mater., vol. 59, no. 5, pp. 1986–1994, Mar. 2011. 6 A. E. Bayoumi and J. Q. Xie, “Some metallurgical aspects of chip formation in cutting Ti-6wt.%Al-4wt.%V alloy,” Mater. Sci. Eng. A, vol. 190, no. 1–2, pp. 173–180, Jan. 1995. 7 A. Fitzner, M. Thomas, J. Q. Fonseca, S. Y. Zhang, J. Kelleher, and M. Preuss, “The Effect of Aluminium on Deformation and Twinning in Alpha Titanium: The ND Case,” in Proceedings of the 13th World Conference on Titanium, Hoboken, NJ, USA: John Wiley & Sons, Inc., 2016, pp. 1051–1055. 8 A. Ghaderi and M. R. Barnett, “Sensitivity of deformation twinning to grain size in titanium and magnesium,” Acta Mater., vol. 59, no. 20, pp. 7824–7839, Dec. 2011. 9 A. Ginting and M. Nouari, “Surface integrity of dry machined titanium alloys,” Int. J. Mach. Tools Manuf., vol. 49, no. 3–4, pp. 325–332, Mar. 2009. 10 A. Gittens, “ACI’s World Airport Traffic Forecasts reveal the drivers of air transport demand growth on the path to 2040,” ACI World, 2019. [Online]. Available: https://www.internationalairportreview.com/article/106229/world-airport-traffic-forecasts-aci-world/. [Accessed: 01-May-2020]. 11 A. Hosseini and H. A. Kishawy, “Cutting Tool Materials and Tool Wear,” in Machining of Titanium Alloys, 2014, pp. 31–56. 12 A. J. Makadia and J. I. Nanavati, “Optimisation of machining parameters for turning operations based on response surface methodology,” Measurement, vol. 46, no. 4, pp. 1521–1529, 2013. 13 A. J. Wagoner Johnson, C. W. Bull, K. S. Kumar, and C. L. Briant, “The influence of microstructure and strain rate on the compressive deformation behavior of Ti-6Al-4V,” Metall. Mater. Trans. A, vol. 34, no. 2, pp. 295–306, Feb. 2003. 14 A. Jawaid, C. H. Che-Haron, and A. Abdullah, “Tool wear characteristics in turning of titanium alloy Ti-6246,” J. Mater. Process. Technol., vol. 92–93, pp. 329–334, Aug. 1999. 15 A. Kara, A. Tasdemirci, and M. Guden, “Modeling quasi-static and high strain rate deformation and failure behavior of a (±45) symmetric E-glass/polyester composite under compressive loading,” Mater. Des., vol. 49, pp. 566–574, Aug. 2013. 16 A. Molinari, C. Musquar, and G. Sutter, “Adiabatic shear banding in high speed machining of Ti–6Al–4V: experiments and modeling,” Int. J. Plast., vol. 18, no. 4, pp. 443–459, Apr. 2002. 17 A. P. Markopoulos, Finite Element Method in Machining Processes. London: Springer London, 2013. 18 A. Polishetty, M. Shunmugavel, M. Goldberg, G. Littlefair, and R. K. Singh, “Cutting Force and Surface Finish Analysis of Machining Additive Manufactured Titanium Alloy Ti-6Al-4V,” Procedia Manuf., vol. 7, pp. 284–289, Jan. 2017. 19 A. R. C. Sharman, J. I. Hughes, and K. Ridgway, “The effect of tool nose radius on surface integrity and residual stresses when turning Inconel 718TM,” J. Mater. Process. Technol., vol. 216, pp. 123–132, 2015. 20 A. R. Machado and J. Wallbank, “Machining of Titanium and its Alloys—a Review,” Proc. Inst. Mech. Eng. Part B J. Eng. Manuf., vol. 204, no. 1, pp. 53–60, 1990. 21 A. Rohatgi, K. S. Vecchio, and G. T. Gray, “The influence of stacking fault energy on the mechanical behavior of Cu and Cu-Al alloys: Deformation twinning, work hardening, and dynamic recovery,” Metall. Mater. Trans. A, vol. 32, no. 1, pp. 135–145, Jan. 2001. 22 Arrazola PJ, Garay A, Iriarte LM, et al. Machinability of titanium alloys (Ti6Al4V and Ti555.3). J Mater Process Technol 2009; 209: 2223–2230. 23 B. Chandra Behera, C. Sudarsan Ghosh, and V. R. Paruchuri, “Study of saw-tooth chip in machining of Inconel 718 by metallographic technique,” Mach. Sci. Technol., vol. 23, no. 3, pp. 431–454, May 2019. 24 B. Davis, D. Dabrow, P. Ifju, G. Xiao, S. Y. Liang, and Y. Huang, “Study of the Shear Strain and Shear Strain Rate Progression During Titanium Machining,” J. Manuf. Sci. Eng., vol. 140, no. 5, May 2018. 25 B. Mills and A. H. Redford, Machinability of Engineering Materials. Applied Science Publishers, 1983. 26 Bai W, Sun R, Roy A, et al. Improved analytical prediction of chip formation in orthogonal cutting of titanium alloy Ti6Al4V. Int J Mech Sci 2017; 133: 357–367. 27 Bäker M, Rösler J, Siemers C. The influence of thermal conductivity on segmented chip formation. In: Computational Materials Science. 2003, pp. 175–182. 28 C. Dredge, R. M’Saoubi, B. Thomas, O. Hatt, M. Thomas, and M. Jackson, “A low-cost machinability approach to accelerate titanium alloy development,” Proc. Inst. Mech. Eng. Part B J. Eng. Manuf., Jul. 2020. 29 C. Gao and L. Zhang, “Effect of cutting conditions on the serrated chip formation in high-speed machining,” Mach. Sci. Technol., vol. 17, no. 1, pp. 26–40, Jan. 2013. 30 C. H. Che-Haron and A. Jawaid, “The effect of machining on surface integrity of titanium alloy Ti-6% Al-4% v,” J. Mater. Process. Technol., vol. 166, no. 2, pp. 188-192, Aug. 2005. 31 C. H. Che-Haron, “Tool life and surface integrity in turning titanium alloy,” J. Mater. Process. Technol., vol. 118, no. 1–3, pp. 231–237, Dec. 2001. 32 C. M. Taylor, S. G. Abrego Hernandez, M. Marshall, and M. Broderick, “Cutting fluid application for titanium alloys Ti-6Al-4V and Ti-10V-2Fe-3Al in a finish turning process,” Procedia CIRP, vol. 77, pp. 441–444, 2018. 33 C. Ramirez et al., “Understanding the diffusion wear mechanisms of WC-10%Co carbide tools during dry machining of titanium alloys,” Wear, vol. 390–391, pp. 61–70, Nov. 2017. 34 C. Veiga, J. P. Davim, and A. J. R. Loureiro, “Review on machinability of titanium alloys: The process perspective,” Rev. Adv. Mater. Sci., vol. 34, no. 2, pp. 148–164, 2013. 35 C. Zheng et al., “Effect of microstructures on ballistic impact property of Ti–6Al–4V targets,” Mater. Sci. Eng. A, vol. 608, pp. 53–62, Jul. 2014. 36 Chandrasekaran H, M’saoubi R, Chazal H. Modelling of material flow stress in chip formation process from orthogonal milling and Split Hopkinson bar tests. Mach Sci Technol 2005; 9: 131–145. 37 Chen G, Ren C, Yu W, et al. Application of genetic algorithms for optimizing the Johnson–Cook constitutive model parameters when simulating the titanium alloy Ti-6Al-4V machining process. Proc Inst Mech Eng Part B J Eng Manuf 2012; 226: 1287–1297. 38 Cockroft MG, Latham DJ. Ductility and the Workability of Metals. J Inst Met 1968; 96: 33–39. 39 Cotterell M, Byrne G. Characterisation of chip formation during orthogonal cutting of titanium alloy Ti–6Al–4V. CIRP J Manuf Sci Technol 2008; 1: 81–85. 40 Cotterell M, Byrne G. Dynamics of chip formation during orthogonal cutting of titanium alloy Ti–6Al–4V. CIRP Ann 2008; 57: 93–96. 41 Crawforth P, Wynne B, Turner S, et al. Subsurface deformation during precision turning of a near-alpha titanium alloy. Scr Mater 2012; 67: 842–845. 42 D. Carou and J. P. Davim, Machining of Light Alloys. CRC Press, 2018. 43 D. G. Lee, S. Kim, S. Lee, and C. Soo Lee, “Effects of microstructural morphology on quasi-static and dynamic deformation behavior of Ti-6Al-4V alloy,” Metall. Mater. Trans. A, vol. 32, no. 2, pp. 315–324, Feb. 2001. 44 D. G. Lee, Y. H. Lee, S. Lee, C. S. Lee, and S. M. Hur, “Dynamic deformation behavior and ballistic impact properties of Ti-6Al-4V alloy having equiaxed and bimodal microstructures,” Metall. Mater. Trans. A, vol. 35, no. 10, pp. 3103–3112, Oct. 2004. 45 D. J. Truax and C. J. McMahon, “Plastic behavior of titanium-aluminum alloys,” Mater. Sci. Eng., vol. 13, no. 2, pp. 125–139, Feb. 1974. 46 D. Jeong, J. Park, S. Ahn, H. Sung, Y. Kwon, and S. Kim, “Effect of stabilization annealing on SCC susceptibility of β-annealed Ti-6Al-4V alloy in 0.6 M NaCl solution,” Met. Mater. Int., vol. 24, no. 1, pp. 101–111, Jan. 2018. 47 D. Jianxin, L. Yousheng, and S. Wenlong, “Diffusion wear in dry cutting of Ti–6Al–4V with WC/Co carbide tools,” Wear, vol. 265, no. 11, pp. 1776–1783, 2008. 48 D. K. Yang, P. Cizek, P. D. Hodgson, and C. E. Wen, “Microstructure evolution and nanograin formation during shear localization in cold-rolled titanium,” Acta Mater., vol. 58, no. 13, pp. 4536–4548, 2010. 49 D. Kuhlmann-Wilsdorf, “Theory of plastic deformation: - properties of low energy dislocation structures,” Mater. Sci. Eng. A, vol. 113, pp. 1–41, Jul. 1989. 50 D. Nguyen, D. Kang, T. Bieler, K. Park, and P. Kwon, “Microstructural impact on flank wear during turning of various Ti-6Al-4V alloys,” Wear, vol. 384–385, pp. 72–83, Aug. 2017. 51 D. R. Askeland, P. P. Fulay, and W. J. Wright, The Science and Engineering of Materials, Sixth. Global Engineering, 1984. 52 D. T. Nguyen, Y. S. Kim, and D. W. Jung, “Flow stress equations of Ti-6Al-4V titanium alloy sheet at elevated temperatures,” Int. J. Precis. Eng. Manuf., vol. 13, no. 5, pp. 747–751, May 2012. 53 D. Tromans, “Elastic Anistropy of HCP Metal Crystals and Polycrystals,” Int. J. Res. Rev. Appl. Sci., vol. 6, no. 4, pp. 462–483, 2011. 54 Devotta A, Sivaprasad P, Beno T, et al. A Modified Johnson-Cook Model for Ferritic-Pearlitic Steel in Dynamic Strain Aging Regime. Metals (Basel) 2019; 9: 528. 55 Dorogoy A, Rittel D. Determination of the Johnson – Cook Material Parameters Using the SCS Specimen. Exp Mech 2009; 49: 881. 56 E. Booser, CRC Handbook of Lubrication and Tribology, Volume III: Monitoring. CRC Press, 1993. 57 E. Levine, “Deformation mechanisms in titanium at low temperatures,” AIME MET SOC TRANS, vol. 236, no. 11, pp. 1558–1565, 1966. 58 E. M. Trent and P. K. Wright, Metal Cutting, 4th ed. 1991. 59 E. O. Ezugwu and Z. M. Wang, “Titanium alloys and their machinability—a review,” J. Mater. Process. Technol., vol. 68, no. 3, pp. 262–274, Aug. 1997. 60 E. O. Ezugwu, J. Bonney, R. B. Da Silva, and O. Çakir, “Surface integrity of finished turned Ti–6Al–4V alloy with PCD tools using conventional and high pressure coolant supplies,” Int. J. Mach. Tools Manuf., vol. 47, no. 6, pp. 884–891, 2007. 61 E. O. Hall, “The Deformation and Ageing of Mild Steel: III Discussion of Results,” Proc. Phys. Soc. Sect. B, vol. 64, no. 9, pp. 747–753, Sep. 1951. 62 F. Barlat, O. Cazacu, M. Życzkowski, D. Banabic, and J. W. Yoon, “Yield Surface Plasticity and Anisotropy,” in Continuum Scale Simulation of Engineering Materials, Weinheim, FRG: Wiley-VCH Verlag GmbH & Co. KGaA, 2005, pp. 145–183. 63 F. W. Taylor, “On the art of cutting metals”, Book, American Society of Mechanical Engineers, 1906. 64 F. Wang, J. Zhao, A. Li, and J. Zhao, “Experimental Study on Cutting Forces and Surface Integrity in High-Speed Side Milling of Ti-6Al-4V Titanium Alloy,” Mach. Sci. Technol., vol. 18, no. 3, pp. 448–463, Jul. 2014. 65 G. A. Salishchev and S. Y. Mironov, “Effect of Grain Size on Mechanical Properties of Commercially Pure Titanium,” Russ. Phys. J., vol. 44, no. 6, pp. 596–601, 2001. 66 G. E. P. Box and K. B. Wilson, “On the Experimental Attainment of Optimum Conditions,” J. R. Stat. Soc. Ser. B, vol. 13, no. 1, pp. 1–38, Jan. 1951. 67 G. Lütjering and J. C. Williams, Titanium, 2nd ed. Springer, 2007. 68 G. Lütjering, “Influence of processing on microstructure and mechanical properties of (α+β) titanium alloys,” Mater. Sci. Eng. A, pp. 32–45, 1998. 69 G. Sutter, “Chip geometries during high-speed machining for orthogonal cutting conditions,” Int. J. Mach. Tools Manuf., vol. 45, no. 6, pp. 719–726, 2005. 70 G. T. Smith, Cutting Tool Technology: Industrial Handbook. 2008. 71 Groover M. Fundamentals of Modern Manufacturing Materials, Processes and Systems. 4th Editio. John Wiley & Sons Inc, 2011. 72 Guo YB, Wen Q, Woodbury KA. Dynamic material behavior modeling using internal state variable plasticity and its application in hard machining simulations. J Manuf Sci Eng Trans ASME 2006; 128: 749–759. 73 H. Becker and W. Pantleon, “Work-hardening stages and deformation mechanism maps during tensile deformation of commercially pure titanium,” Comput. Mater. Sci., vol. 76, pp. 52–59, 2013. 74 H. E. Chandler, Metals Handbook. 1978. 75 H. J. Bunge, “The basic concepts of texture investigation in polycrystalline materials,” Steel Res., vol. 62, no. 12, pp. 530–541, Dec. 1991. 76 H. K. Toenshoff, “Machinability,” in CIRP Encyclopedia of Production Engineering, Berlin, Heidelberg: Springer Berlin Heidelberg, 2014, pp. 769–770. 77 H. M. Flower, “Microstructural development in relation to hot working of titanium alloys,” vol. 6, no. 11, pp. 1082–1092, 1990. 78 Hastings WF, Oxley PLB, Stevenson MG. Predicting a Material’s Machining Characteristics Using Flow Stress Properties Obtained from High-Speed Compression Tests. Proc Inst Mech Eng 1974; 188: 245–252. 79 Hatt O, Crawforth P, Jackson M. On the mechanism of tool crater wear during titanium alloy machining. Wear 2017; 374: 15–20. 80 Hatt O, Larsson H, Giuliani F, et al. Predicting Chemical Wear in Machining Titanium Alloys Via a Novel Low Cost Diffusion Couple Method. Procedia CIRP 2016; 45: 219–222. 81 Hatt O, Lomas Z, Thomas M, et al. The effect of titanium alloy chemistry on machining induced tool crater wear characteristics. Wear 2018; 408–409: 200–207. 82 I. Inagaki, T. Takechi, Y. Shirai, and N. Ariyasu, “Application and Features of Titanium for the Aerospace Industry,” 2014. 83 I. J. Polmear, “Titanium alloys,” in Light Alloys, Elsevier, 2005, pp. 299–365. 84 J. A. Venables, “The electron microscopy of deformation twinning,” J. Phys. Chem. Solids, vol. 25, no. 7, pp. 685–692, 1964. 85 J. C. Williams, R. G. Baggerly, and N. E. Paton, “Deformation behavior of HCP Ti-Al alloy single crystals,” Metall. Mater. Trans. A Phys. Metall. Mater. Sci., vol. 33, no. 3, pp. 837–850, 2002. 86 J. G. Schneider, “Cutting Tool Applications,” Book, ISBN-10: 0615121918, 2002. 87 J. Hou, W. Zhou, H. Duan, G. Yang, H. Xu, and N. Zhao, “Influence of cutting speed on cutting force, flank temperature, and tool wear in end milling of Ti-6Al-4V alloy,” Int. J. Adv. Manuf. Technol., vol. 70, no. 9–12, pp. 1835–1845, Feb. 2014. 88 J. Jeong, M. Alfreider, R. Konetschnik, D. Kiener, and S. H. Oh, “In-situ TEM observation of {101¯2} twin-dominated deformation of Mg pillars: Twinning mechanism, size effects and rate dependency,” Acta Mater., vol. 158, pp. 407–421, Oct. 2018. 89 J. Lindemann and L. Wagner, “Microtextural effects on mechanical properties of duplex microstructures in (α+β) titanium alloys,” Mater. Sci. Eng. A, vol. 263, no. 2, pp. 137–141, May 1999. 90 J. P. Davim, Machinability of Advanced Materials. Hoboken, NJ, USA: John Wiley & Sons, Inc., 2014. 91 J. P. Hirth, J. Lothe, and T. Mura, “Theory of Dislocations (2nd ed.),” J. Appl. Mech., vol. 50, no. 2, pp. 476–477, Jun. 1983. 92 J. Ribeiro, H. Lopes, L. Queijo, and D. Figueiredo, “Optimization of Cutting Parameters to Minimize the Surface Roughness in the End Milling Process Using the Taguchi Method,” Period. Polytech. Mech. Eng., vol. 61, no. 1, pp. 30–35, 2017. 93 J. Sun, S. Huang, T. Wang, and W. Chen, “Research on surface integrity of turning titanium alloy TB6,” Procedia CIRP, vol. 71, pp. 484–489, Jan. 2018. 94 J. W. Christian and S. Mahajan, “Deformation twinning,” Prog. Mater. Sci., vol. 39, no. 1–2, pp. 1–157, 1995. 95 J. W. Won, D. Kim, S. G. Hong, and C. S. Lee, “Anisotropy in twinning characteristics and texture evolution of rolling textured high purity alpha phase titanium,” J. Alloys Compd., vol. 683, pp. 92–99, 2016. 96 J. Zang, J. Zhao, A. Li, and J. Pang, “Serrated chip formation mechanism analysis for machining of titanium alloy Ti-6Al-4V based on thermal property,” Int. J. Adv. Manuf. Technol., vol. 98, no. 1–4, pp. 119–127, 2018. 97 J. Zhou, V. Bushlya, R. L. Peng, Z. Chen, S. Johansson, and J. E. Stahl, “Analysis of Subsurface Microstructure and Residual Stresses in Machined Inconel 718 with PCBN and Al2O3-SiCw Tools,” Procedia CIRP, vol. 13, pp. 150–155, 2014. 98 James S, Kosaka Y, Thomas R, et al. Timetal® 407: A Titanium Alloy to Enable Cost Reduction. In: Proceedings of the 13th World Conference on Titanium. 2016, pp. 721–725. 99 Johnson GR, Cook WH. Fracture characteristics of three metals subjected to various strains, strain rates, temperatures and pressures. Eng Fract Mech 1985; 21: 31–48. 100 K. Ohgo, “The adhesion mechanism of the built-up edge and the layer on the rake face of a cutting tool,” Wear, vol. 51, no. 1, pp. 117-126, 1978. 101 K. Viswanathan, S. Yadav and D. Sagapuram, “Shear bands in materials processing: Understanding the mechanics of flow localization from Zener’s time to the present,” Appl. Mech. Rev., vol. 72, no.6, pp. 17, Jan. 2021. 102 K. Zhang, K. V. Yang, S. Lim, X. Wu, and C. H. J. Davies, “Effect of the presence of macrozones on short crack propagation in forged two-phase titanium alloys,” Int. J. Fatigue, vol. 104, pp. 1–11, Nov. 2017. 103 Kay G. Failure Modeling of Titanium-6Al-4V and 2024-T3 Aluminum with the Johnson-Cook Material Model. 2002; 1–28. 104 Khan AS, Sung Suh Y, Kazmi R. Quasi-static and dynamic loading responses and constitutive modeling of titanium alloys. Int J Plast 2004; 20: 2233–2248. 105 Kiranli E. Determination of material constitutive equation of a biomedical grade Ti-6Al-4V alloy for cross-wedge rolling. Izmir Institute of Technology, 2009. 106 Kloenne Z, Viswanathan G, Thomas M, et al. A Comparative Study on the Substructure Evolution and Mechanical Properties of TIMETAL 407 and Ti-64. In: The 14th World Conference on Titanium Proceedings. 2019, pp. 1–6. 107 Komanduri R, Hou Z. On Thermoplastic Shear Instability in the Machining of a Titanium Alloy (Ti-6Al-4V). Metall Mater Trans A 2002; 33: 1–16. 108 L. B. Abhang and M. Hameedullah, “Optimization of Machining Parameters in Steel Turning Operation by Taguchi Method,” Procedia Eng., vol. 38, pp. 40–48, 2012. 109 L. Chen, T. I. El-Wardany, and W. C. Harris, “Modelling the Effects of Flank Wear Land and Chip Formation on Residual Stresses,” CIRP Ann., vol. 53, no. 1, pp. 95–98, Jan. 2004. 110 L. Marshall, “The influence of aluminium additions on titanium during machining through the application of a novel orthogonal cutting test method,” University of Sheffield, 2014. 111 L. Marshall, “The influence of aluminium additions on titanium during machining through the application of a novel orthogonal cutting test method.” PhD Thesis, Uni. of Shef., 2014, https://etheses.whiterose.ac.uk/7352/ 112 L. Marshall, B. Wynne, S. Turner, and M. Jackson, “Influence of Aluminium Content on the Machinability and Subsurface Deformation Of Titanium Alloys,” in Proceedings of the 13th World Conference on Titanium, Hoboken, NJ, USA: John Wiley & Sons, Inc., 2016, pp. 923–928. 113 Laakso SVA, Niemi E. Determination of material model parameters from orthogonal cutting experiments. Proc Inst Mech Eng Part B J Eng Manuf 2016; 230: 848–857. 114 Lee W, Lin C. High-temperature deformation behaviour of Ti6Al4V alloy evaluated by high strain-rate compression tests. J Mater Process Technol 1998; 75: 127–136. 115 Lee W, Lin C. Plastic deformation and fracture behaviour of Ti–6Al–4V alloy loaded with high strain rate under various temperatures. Mater Sci Eng A 1998; 241: 48–59. 116 Lütjering G, Williams JC. Titanium. 2nd ed. Springer, 2007. 117 M. Aceves-Lopez, “Subsurface deformation micro-mechanisms induced during machining of titanium alloys at low temperatures, and a new method to examine their machining behaviour,” University of Sheffield, 2018. 118 M. Ahmed, D. Wexler, G. Casillas, D. G. Savvakin, and E. V. Pereloma, “Strain rate dependence of deformation-induced transformation and twinning in a metastable titanium alloy,” Acta Mater., vol. 104, pp. 190–200, Feb. 2016. 119 M. Armendia, A. Garay, L. M. Iriarte, and P. J. Arrazola, “Comparison of the machinabilities of Ti6Al4V and TIMETAL® 54M using uncoated WC–Co tools,” J. Mater. Process. Technol., vol. 210, no. 2, pp. 197–203, Jan. 2010. 120 M. Armendia, P. Osborne, A. Garay, J. Belloso, S. Turner, and P. Arrazola, “Influence of Heat Treatment on the Machinability of Titanium Alloys,” Mater. Manuf. Process., vol. 27, no. 4, pp. 457–461, 2012. 121 M. Arul Kumar, M. Wroński, R. J. McCabe, L. Capolungo, K. Wierzbanowski, and C. N. Tomé, “Role of microstructure on twin nucleation and growth in HCP titanium: A statistical study,” Acta Mater., vol. 148, pp. 123–132, 2018. 122 M. Bache, H. Davies, W. Davey, M. Thomas, and I. Berment-Parr, “Microstructural Control of Fatigue Behaviour in a Novel alpha+beta Titanium Alloy,” Metals (Basel)., vol. 9, no. 11, p. 1200, Nov. 2019. 123 M. Battaini, “Deformation Behaviour and Twinning Mechanisms of Commercially Pure Titanium Alloys,” Monash University, 2008. 124 M. Cotterell and G. Byrne, “Dynamics of chip formation during orthogonal cutting of titanium alloy Ti–6Al–4V,” CIRP Ann., vol. 57, no. 1, pp. 93–96, Jan. 2008. 125 M. D. F. Rahman, “Stress and Strain Distributions during Machining of Ti-6Al-4V at Ambient and Cryogenic Temperatures,” University of Windsor, 2014. 126 M. Donachie Jr., Titanium – A Technical Guide, 2nd ed. 2000. 127 M. E. Merchant, “Mechanics of the metal cutting process. I. Orthogonal cutting and a type 2 chip,” J. Appl. Phys., Vol. 16, no. 5, 1945, https://doi.org/10.1063/1.1707586. 128 M. Groover, Fundamentals of Modern Manufacturing Materials, Processes and Systems, 4th Editio. John Wiley & Sons Inc, 2011. 129 M. H. Miguélez, X. Soldani, and A. Molinari, “Analysis of adiabatic shear banding in orthogonal cutting of Ti alloy,” Int. J. Mech. Sci., vol. 75, pp. 212–222, Oct. 2013. 130 M. Jackson and R. R. Boyer, “Titanium and its Alloys: Processing, Fabrication and Mechanical Performance,” Encycl. Aerosp. Eng., vol. 9, no. 6, p. 689, Dec. 2010. 131 M. Nalbant, H. Gökkaya, and G. Sur, “Application of Taguchi method in the optimization of cutting parameters for surface roughness in turning,” Mater. Des. vol. 28, no. 4, pp. 1379–1385, Jan. 2007. 132 M. Peters, J. Kumpfert, C. H. Ward, and C. Leyens, “Titanium Alloys for Aerospace Applications,” Adv. Eng. Mater., vol. 5, no. 6, pp. 419–427, Jun. 2003. 133 M. Thomas, S. Turner, and M. Jackson, “Microstructural damage during high-speed milling of titanium alloys,” Scr. Mater., vol. 62, no. 5, pp. 250–253, 2010. 134 Macdougall DAS, Harding J. A constitutive relation and failure criterion for Ti6Al4V alloy at impact rates of strain. J Mech Phys Solids 1999; 47: 1157–1185. 135 Machado AR, Wallbank J. Machining of Titanium and its Alloys—a Review. Proc Inst Mech Eng Part B J Eng Manuf 1990; 204: 53–60. 136 Marshall L, Wynne B, Turner S, et al. Influence of Aluminium Content on the Machinability and Subsurface Deformation Of Titanium Alloys. In: Proceedings of the 13th World Conference on Titanium. Hoboken, NJ, USA: John Wiley & Sons, Inc., pp. 923–928. 137 Marshall L. The influence of aluminium additions on titanium during machining through the application of a novel orthogonal cutting test method. University of Sheffield, 2014. 138 Meyer HW, Kleponis DS. Modeling the high strain rate behavior of titanium undergoing ballistic impact and penetration. Int J Impact Eng 2001; 26: 509–521. 139 Miguélez MH, Soldani X, Molinari A. Analysis of adiabatic shear banding in orthogonal cutting of Ti alloy. Int J Mech Sci 2013; 75: 212–222. 140 Miguélez MH, Zaera R, Molinari A, et al. Residual Stresses in Orthogonal Cutting of Metals: The Effect of Thermomechanical Coupling Parameters and of Friction. J Therm Stress 2009; 32: 269–289. 141 Molinari A, Musquar C, Sutter G. Adiabatic shear banding in high speed machining of Ti–6Al–4V: experiments and modeling. Int J Plast 2002; 18: 443–459. 142 N. C. Tsourveloudis, “Predictive Modeling of the Ti6Al4V Alloy Surface Roughness,” J. Intell. Robot. Syst., vol. 60, no. 3–4, pp. 513–530, Dec. 2010. 143 N. Fang and Q. Wu, “A comparative study of the cutting forces in high speed machining of Ti–6Al–4V and Inconel 718 with a round cutting edge tool,” J. Mater. Process. Technol., vol. 209, no. 9, pp. 4385–4389, May 2009. 144 N. Gey, P. Bocher, E. Uta, L. Germain, and M. Humbert, “Texture and microtexture variations in a near-α titanium forged disk of bimodal microstructure,” Acta Mater., vol. 60, no. 6, pp. 2647–2655, 2012. 145 N. J. Petch and J. Iron, “The cleavage strength of polycrystals,” Steel Inst., vol. 173, pp. 25–28, 1953. 146 N. Khanna and K. S. Sangwan, “Comparative machinability study on Ti54M titanium alloy in different heat treatment conditions,” Proc. Inst. Mech. Eng. Part B J. Eng. Manuf., vol. 227, no. 1, pp. 96–101, Jan. 2013. 147 N. Khanna and K. S. Sangwan, “Machinability analysis of heat treated Ti64, Ti54M and Ti10.2.3 titanium alloys,” Int. J. Precis. Eng. Manuf., vol. 14, no. 5, pp. 719–724, May 2013. 148 N. Khanna, A. Garay, L. M. Iriarte, D. Soler, K. S. Sangwan, and P. J. Arrazola, “Effect of heat Treatment Conditions on the Machinability of Ti64 and Ti54M Alloys,” Procedia CIRP, vol. 1, pp. 477–482, 2012. 149 N. Narutaki, A. Murakoshi, S. Motonishi, and H. Takeyama, “Study on Machining of Titanium Alloys,” CIRP Ann., vol. 32, no. 1, pp. 65–69, Jan. 1983. 150 N. P. Gurao, R. Kapoor, and S. Suwas, “Deformation behaviour of commercially pure titanium at extreme strain rates,” Acta Mater., vol. 59, no. 9, pp. 3431–3446, 2011. 151 N. Tomac, K. Sørby, and S. Doboviček, “Formation of built-up layer on the tool in turning operation of magnesium alloys,” Teh. Vjesn., vol. 25, no. 3, pp. 940–943, 2018. 152 Nasr M, Ng E, Elbestawi M. Effects of workpiece thermal properties on machining-induced residual stresses - thermal softening and conductivity. Proc Inst Mech Eng Part B J Eng Manuf 2007; 221: 1387–1400. 153 Nemat-Nasser S, Guo WG, Nesterenko VF, et al. Dynamic response of conventional and hot isostatically pressed Ti–6Al–4V alloys: experiments and modeling. Mech Mater 2001; 33: 425–439. 154 O. Engler and V. Randle, Introduction to Texture Analysis; Macrotexture, microtexture, and orientation mapping. CRC Press, 2009. 155 O. Hatt, H. Larsson, F. Giuliani, P. Crawforth, B. Wynne, and M. Jackson, “Predicting Chemical Wear in Machining Titanium Alloys Via a Novel Low Cost Diffusion Couple Method,” Procedia CIRP, vol. 45, pp. 219–222, 2016. 156 O. Hatt, P. Crawforth, and M. Jackson, “On the mechanism of tool crater wear during titanium alloy machining,” Wear, vol. 374, pp. 15–20, 2017. 157 Odelros S, Kaplan B, Kritikos M, et al. Experimental and theoretical study of the microscopic crater wear mechanism in titanium machining. Wear 2017; 376–377: 115–124. 158 Oliaei SNB, Karpat Y. Built-up edge effects on process outputs of titanium alloy micro milling. Precis Eng 2017; 49: 305–315. 159 Oliaei SNB, Karpat Y. Investigating the influence of built-up edge on forces and surface roughness in micro scale orthogonal machining of titanium alloy Ti6Al4V. J Mater Process Technol 2016; 235: 28–40. 160 Oxley PLB. The Mechanics of machining: An analytical approach to assessing machinability. Halsted Press, 1989. 161 P. A. Dearnley and A. N. Grearson, “Evaluation of principal wear mechanisms of cemented carbides and ceramics used for machining titanium alloy IMI 318,” Mater. Sci. Technol., vol. 2, no. 1, pp. 47–58, Jan. 1986. 162 P. Davies, R. Thomas, P. Garratt, N. Green, M. Coleman, and S. Birosca, “The Effect of Elevated Temperature Exposure on the Mechanical Properties of Ti834,” in Proceedings of the 13th World Conference on Titanium, Hoboken, NJ, USA: John Wiley & Sons, Inc., 2016, pp. 1625–1630. 163 P. Dobroň, F. Chmelík, S. Yi, K. Parfenenko, D. Letzig, and J. Bohlen, “Grain size effects on deformation twinning in an extruded magnesium alloy tested in compression,” Scr. Mater., vol. 65, no. 5, pp. 424–427, 2011. 164 P. G. Partridge, “Cyclic twinning in fatigued close-packed hexagonal metals,” Philos. Mag. A J. Theor. Exp. Appl. Phys., vol. 12, no. 119, pp. 1043–1054, Nov. 1965. 165 P. G. Partridge, “The crystallography and deformation modes of hexagonal close-packed metals,” Metall. Rev., vol. 12, no. 1, pp. 169–194, Jan. 1967. 166 P. J. Arrazola, A. Garay, L. M. Iriarte, M. Armendia, S. Marya, and F. Le Maître, “Machinability of titanium alloys (Ti6Al4V and Ti555.3),” J. Mater. Process. Technol., vol. 209, no. 5, pp. 2223–2230, 2009. 167 Polishetty A, Shunmugavel M, Goldberg M, et al. Cutting Force and Surface Finish Analysis of Machining Additive Manufactured Titanium Alloy Ti-6Al-4V. Procedia Manuf 2017; 7: 284–289. 168 Q. Wang and Z. Liu, “Plastic deformation induced nano-scale twins in Ti-6Al-4V machined surface with high speed machining,” Mater. Sci. Eng. A, vol. 675, pp. 271–279, Oct. 2016. 169 R. Ding, J. Gong, A. J. Wilkinson, and I. P. Jones, “〈c+a〉 Dislocations in deformed Ti–6Al–4V micro-cantilevers,” Acta Mater., vol. 76, pp. 127–134, 2014. 170 R. K. Gupta, C. Mathew, and P. Ramkumar, “Strain Hardening in Aerospace Alloys,” Front. Aerosp. Eng., vol. 4, no. 1, pp. 1–13, 2015. 171 R. Komanduri and B. F. Von Turkovich, “New observations on the mechanism of chip formation when machining titanium alloys,” Wear, vol. 69, no. 2, pp. 179–188, Jun. 1981. 172 R. Komanduri and Z. Hou, “On Thermoplastic Shear Instability in the Machining of a Titanium Alloy (Ti-6Al-4V),” Metall. Mater. Trans. A, vol. 33, no. 9, pp. 1–16, 2002. 173 R. Lalbondre, P. Krishna, and G. C. Mohankumar, “An Experimental Investigation on Machinability Studies of Steels by Face Turning,” Procedia Mater. Sci., vol. 6, pp. 1386–1395, 2014. 174 R. Reed-Hill and R. Abbaschian, Physical Metallurgy Principles, 3rd ed. Boston: International Thomson Publishing, 1994. 175 R. V. Mises, “Mechanik der plastischen Formänderung von Kristallen,” ZAMM - Zeitschrift für Angew. Math. und Mech., vol. 8, no. 3, pp. 161–185, 1928. 176 R. Wanhill and S. Barter, Fatigue of Beta Processed and Beta Heat-treated Titanium Alloys. Dordrecht: Springer Netherlands, 2012. 177 R. Y. Y. Ma, Q. Xue, H. Wang, S. Huang, J. Qiu, X. Feng, J. Lei, “Deformation Twinning in Fatigue Crack Tip Plastic Zone of Ti-6al-4v Alloy with Widmanstatten Microstructure,” Mater. Charact., vol. 132, pp. 338–347, 2017. 178 Ramaswami R. The effect of the built-up-edge (BUE) on the wear of cutting tools. Wear 1971; 18: 1–10. 179 S. A. Niknam, R. Khettabi, and V. Songmene, “Machinability and Machining of Titanium Alloys: A Review,” in Materials Forming, Machining and Tribology, 2014, pp. 1–30. 180 S. H. Rhim and S. I. Oh, “Prediction of serrated chip formation in metal cutting process with new flow stress model for AISI 1045 steel,” J. Mater. Process. Technol., vol. 171, no. 3, pp. 417–422, Feb. 2006. 181 S. I. Jaffery and P. T. Mativenga, “Assessment of the machinability of Ti-6Al-4V alloy using the wear map approach,” Int. J. Adv. Manuf. Technol., vol. 40, no. 7–8, pp. 687–696, 2009. 182 S. J. Sun, M. Brandt, and J. P. T. Mo, “Effect of Microstructure on Cutting Force and Chip Formation during Machining of Ti-6Al-4V Alloy,” Adv. Mater. Res., vol. 690–693, pp. 2437–2441, May 2013. 183 S. James, Y. Kosaka, R. Thomas, and P. Garratt, “Timetal® 407: A Titanium Alloy to Enable Cost Reduction,” in Proceedings of the 13th World Conference on Titanium, 2016, pp. 721–725. 184 S. Nemat-Nasser, W. G. Guo, and J. Y. Cheng, “Mechanical properties and deformation mechanisms of a commercially pure titanium,” Acta Mater., vol. 47, no. 13, pp. 3705–3720, Oct. 1999. 185 S. Ramesh, L. Karunamoorthy, and K. Palanikumar, “Surface Roughness Analysis in Machining of Titanium Alloy,” Mater. Manuf. Process., vol. 23, no. 2, pp. 174–181, Jan. 2008. 186 S. Sun, M. Brandt, and M. S. Dargusch, “Characteristics of cutting forces and chip formation in machining of titanium alloys,” Int. J. Mach. Tools Manuf., 2009. 187 S. Sun, M. Brandt, and M. S. Dargusch, “Characteristics of cutting forces and chip formation in machining of titanium alloys,” Int. J. Mach. Tools Manuf., vol. 49, no.7-8, pp. 561-568, June. 2009. 188 S. V. Telrandhe, A. K. Saxena, and S. Mishra, “Effect of microstructure and cutting speed on machining behavior of Ti6Al4V alloy,” J. Mech. Sci. Technol., vol. 31, no. 5, pp. 2177–2184, May 2017. 189 S. Zhang, J. Li, X. Zhu, and H. Lv, “Saw-tooth chip formation and its effect on cutting force fluctuation in turning of Inconel 718,” Int. J. Precis. Eng. Manuf., vol. 14, no. 6, pp. 957–963, Jun. 2013. 190 Salem AA, Kalidindi SR, Doherty RD. Strain hardening of titanium: role of deformation twinning. Acta Mater 2003; 51: 4225–4237. 191 Salem AA, Kalidindi SR, Doherty RD. Strain hardening regimes and microstructure evolution during large strain compression of high purity titanium. Scr Mater 2002; 46: 419–423. 192 Scientific Forming Technologies. DEFORM v11.2. 193 Seo S, Min O, Yang H. Constitutive equation for Ti – 6Al – 4V at high temperatures measured using the SHPB technique. Int J Impact Eng 2005; 31: 735–754. 194 Shatla M, Kerk C, Altan T. Process modeling in machining. Part I: determination of flow stress data. Int J Mach Tools Manuf 2001; 41: 1511–1534. 195 Shrot A, Bäker M. Determination of Johnson–Cook parameters from machining simulations. Comput Mater Sci 2012; 52: 298–304. 196 Storchak, Rupp, Möhring, et al. Determination of Johnson–Cook Constitutive Parameters for Cutting Simulations. Metals (Basel) 2019; 9: 473. 197 Sutter G. Chip geometries during high-speed machining for orthogonal cutting conditions. Int J Mach Tools Manuf 2005; 45: 719–726. 198 T. B. Britton, F. P. E. Dunne, and A. J. Wilkinson, “On the mechanistic basis of deformation at the microscale in hexagonal close-packed metals,” Proc. R. Soc. A Math. Phys. Eng. Sci., vol. 471, no. 2178, 2015. 199 T. Bakša, T. Kroupa, P. Hanzl, and M. Zetek, “Durability of Cutting Tools during Machining of Very Hard and Solid Materials,” Procedia Eng., vol. 100, pp. 1414–1423, 2015. 200 T. Childs, “Metal Machining Theory and Applications,” Mater. Technol., pp. 1–19, 2000. 201 T. Özel and D. Ulutan, “Prediction of machining induced residual stresses in turning of titanium and nickel based alloys with experiments and finite element simulations,” CIRP Ann., vol. 61, no. 1, pp. 547–550, Jan. 2012. 202 T. Sugahara et al., “The effect of Widmanstätten and equiaxed microstructures of Ti-6Al-4V on the oxidation rate and creep behavior,” Mater. Sci. Forum, vol. 636–637, no. June 2014, pp. 657–662, 2010. 203 Thomas M, Turner S, Jackson M. Microstructural damage during high-speed milling of titanium alloys. Scr Mater 2010; 62: 250–253. 204 V. Sinha, M. J. Mills, J. C. Williams, and J. E. Spowart, “Observations on the faceted initiation site in the dwell-fatigue tested Ti-6242 alloy: Crystallographic orientation and size effects,” Metall. Mater. Trans. A, vol. 37, no. 5, pp. 1507–1518, May 2006. 205 W. D. Callister and D. G. Rethwisch, Materials Science and Engineering: An Introduction, 8th ed. Wiley, 2009. 206 W. Davey, M. Bache, H. Davies, and M. Thomas, “Fatigue Performance of the Novel Titanium Alloy Timetal 407,” MATEC Web Conf., vol. 165, p. 4001, May 2018. 207 W. Min, W. Min, and Z. Youzhen, “Diffusion wear in milling titanium alloys,” Mater. Sci. Technol., vol. 4, no. 6, pp. 548–553, Jun. 1988. 208 W. P. Koster, M. Field, L. Fritz, L. R. Gatto, and J. F. Kahles, “Surface Integrity of Machined Structural Components,” Technic. Report, 1970, https://apps.dtic.mil/sti/citations/AD0870146 209 W. Seo, D. Jeong, D. Lee, H. Sung, Y. Kwon, and S. Kim, “Effects of cooling rate and stabilization annealing on fatigue behavior of β-processed Ti-6Al-4V alloys,” Met. Mater. Int., vol. 23, no. 4, pp. 648–659, Jul. 2017. 210 Wyen C, Wegener K. Influence of cutting edge radius on cutting forces in machining titanium. CIRP Ann 2010; 59: 93–96. 211 X. Tan, H. Guo, H. Gu, C. Laird, and N. D. H. Munroe, “Cyclic deformation behavior of high-purity titanium single crystals: Part II. Microstructure and mechanism,” Metall. Mater. Trans. A, vol. 29, no. 2, pp. 513–518, Feb. 1998. 212 X. Yang and C. R. Liu, “Machining titanium and its alloys,” Mach. Sci. Technol., vol. 3, no. 1, pp. 107–139, 1999. 213 Y. B. Chun, S. H. Yu, S. L. Semiatin, and S. K. Hwang, “Effect of deformation twinning on microstructure and texture evolution during cold rolling of CP-titanium,” Mater. Sci. Eng. A, vol. 398, no. 1, pp. 209–219, 2005. 214 Y. B. Egorova, A. A. Il’in, B. A. Kolachev, V. K. Nosov, and A. M. Mamonov, “Effect of the Structure on the Cutability of Titanium Alloys,” Met. Sci. Heat Treat., vol. 45, no. 4, pp. 16–21, 2003. 215 Y. H. Çelik and A. Karabiyik, “Effect of cutting parameters on machining surface and cutting tool in milling of Ti-6Al-4V alloy,” Indian J. Eng. Mater. Sci., vol. 23, no. 5, pp. 349–356, 2016. 216 Y. Kosaka and S. P. Fox, “Influence of alloy chemistry and microstructure on the machinability of titanium alloys,” in Cost-Affordable Titanium: A Symposium Dedicated to Professor Harvey Flower as held at the 2004 TMS Annual Meeting, 2004, pp. 169–176. 217 Y. Kosaka, J. C. Fanning, and S. P. Fox, “Development of low cost high strength alpha/ beta alloy with superior machinability,” in Proceedings of the 10th World Conference on Titanium, 2004, pp. 3028–3034. 218 Y. Seo, S. C. Woo, T. W. Kim, and Y. S. Lee, “Influence of heat treated microstructures on the dynamic deformation characteristics of Ti-6Al-4V alloy,” J. Mech. Sci. Technol., vol. 29, no. 12, pp. 5223–5232, Dec. 2015. 219 Y. T. Zhu, X. Z. Liao, X. L. Wu, and J. Narayan, “Grain size effect on deformation twinning and detwinning,” J. Mater. Sci., vol. 48, no. 13, pp. 4467–4475, Jul. 2013. 220 Y. Xu, J. Zhang, Y. Bai, and M. A. Meyers, “Shear Localization in Dynamic Deformation: Microstructural Evolution,” Metall. Mater. Trans. A, vol. 39, no. 4, pp. 811–843, Apr. 2008. 221 Z. Chen et al., “Effect of thermal exposure on microstructure and nano-hardness of broached Inconel 718,” MATEC Web Conf., vol. 14, p. 08002, Aug. 2014. 222 Z. Kloenne, G. Viswanathan, M. Thomas, M. Loretto, and H. Fraser, “A Comparative Study on the Substructure Evolution and Mechanical Properties of TIMETAL 407 and Ti-64,” in The 14th World Conference on Titanium Proceedings, 2019, pp. 1–6. 223 Z. Li, J. Li, Y. Zhu, X. Tian, and H. Wang, “Variant selection in laser melting deposited α + β titanium alloy,” J. Alloys Compd., vol. 661, pp. 126–135, 2016. 224 Z. W. Huang, P. L. Yong, H. Zhou, and Y. S. Li, “Grain size effect on deformation mechanisms and mechanical properties of titanium,” Mater. Sci. Eng. A, vol. 773, p. 138721, 2020. 225 Z. W. Wyatt, W. J. Joost, D. Zhu, and S. Ankem, “Deformation mechanisms and kinetics of time-dependent twinning in an α-titanium alloy,” Int. J. Plast., vol. 39, pp. 119–131, Dec. 2012. 226 Zhou J, Ren J, Jiang Y. Inverse identification of modified Johnson–Cook model for cutting titanium alloy Ti6Al4V using firefly algorithm. Proc Inst Mech Eng Part B J Eng Manuf 2020; 234: 584–599."]},{"key":"dc:type","label":"Dc Type","values":["Thesis"]},{"key":"dc:type.qualificationlevel","label":"Dc Type Qualificationlevel","values":["doctoral"]},{"key":"dc:type.qualificationname","label":"Dc Type Qualificationname","values":["Eng.D"]}]},{"id":"language_rights","label":"Language and Rights","entries":[{"key":"dc:language.dcterms_iso639_2","label":"Language (ISO 639-2)","values":["eng"]}]},{"id":"identifiers","label":"Identifiers","entries":[{"key":"dc:identifier","label":"Identifier","values":["uk.bl.ethos.834115"]},{"key":"dc:identifier.grantnumber","label":"Dc Identifier Grantnumber","values":["EP/L016257/1"]},{"key":"dc:identifier.uri","label":"Identifier URI","values":["https://etheses.whiterose.ac.uk/id/eprint/29246/1/Thesis_Chap0-6.0_v8.pdf"]}]},{"id":"additional","label":"Additional Metadata","entries":[{"key":"dc:description.abstract","label":"Abstract","values":["An industry focussed research project has been undertaken to evaluate the machinability of an emerging titanium alloy, Timetal 407 and offer a fundamental understanding for the chip control issues. This research identified two key stages in the life cycle of a titanium alloy where consideration of the machinability would provide economic opportunities for the aerospace manufacturing sector. First in the development of emerging alloys and secondly in optimising the cutting parameters during the machining of aerospace components. To assess machinability in the developmental stage of an emerging alloy, a series of small scale experiments were utilised to assess the machinability outputs for Timetal 407 and Ti-6Al-4V, with the aim of drawing conclusions about each of the alloys limitations and strengths in regards to key machinability characteristics; tool wear, chip control, subsurface deformation and cutting forces. The key to these tests was to remain low cost, offering a quick turnaround of results relative to high speed machining, in order to filter out a large number of alloy chemistries and microstructural combinations. For the second stage, machinability maps for Timetal 407 and Ti-6Al-4V were developed using data from high speed machining operations which determined for a range of cutting parameters (cutting speed and feed rate) where machinability outputs were acceptable and Material Removal Rate (MRR) was maximised. The machinability map again incorporated the key machinability characteristics: tool wear, chip control and subsurface deformation as primary points of consideration on the map, with cutting force as a secondary consideration. The map also identified a region of cutting parameters where improved chip management of Timetal 407 could be achieved. Using the high speed machining and small scale machinability experiments, mechanical twins and thermoplastic instability were identified as key determinants for chip control. The outcomes of this research were an ability to characterise machinability using a small scale experimental framework, as well as fulfilling the industry requirements through improving chip management. The improvement of chip management had a number of concurrent benefits to manufacturing operations of large structural gas turbine engine components through reducing cutting time by 43% between Ti-6Al-4V and Timetal 407, whilst also reducing cleaning downtime between parts and reducing machine maintenance to fix issues with chip swarf conveyors. The risk of component rework due to tool breakage or surface finish defects have been reduced, offering potential savings of 300 minutes per part for ‘on machine’ rework, or 480 minutes per part for ‘hand dressing’ by an operator. Due to these operational improvements, the flow of parts through manufacturing facilities has been improved, reducing inventory stock and work in progress."]},{"key":"dc:format","label":"Dc Format","values":["text"]},{"key":"dcterms:accessrights","label":"Dcterms Accessrights","values":["public"]},{"key":"dc:title","label":"Title","values":["Evaluating the Machinability of Titanium Alloys, Timetal 407 and Ti-6Al-4V"]}]}],"canonical_facts":{"dc:contributor.advisor":["Jackson, Martin"],"dc:contributor.sponsor":["EPSRC"],"dc:creator":["Dredge, Christopher"],"dc:date":["2021-01"],"dc:date.issued":["2021-01"],"dc:description.abstract":["An industry focussed research project has been undertaken to evaluate the machinability of an emerging titanium alloy, Timetal 407 and offer a fundamental understanding for the chip control issues. This research identified two key stages in the life cycle of a titanium alloy where consideration of the machinability would provide economic opportunities for the aerospace manufacturing sector. First in the development of emerging alloys and secondly in optimising the cutting parameters during the machining of aerospace components. To assess machinability in the developmental stage of an emerging alloy, a series of small scale experiments were utilised to assess the machinability outputs for Timetal 407 and Ti-6Al-4V, with the aim of drawing conclusions about each of the alloys limitations and strengths in regards to key machinability characteristics; tool wear, chip control, subsurface deformation and cutting forces. The key to these tests was to remain low cost, offering a quick turnaround of results relative to high speed machining, in order to filter out a large number of alloy chemistries and microstructural combinations. For the second stage, machinability maps for Timetal 407 and Ti-6Al-4V were developed using data from high speed machining operations which determined for a range of cutting parameters (cutting speed and feed rate) where machinability outputs were acceptable and Material Removal Rate (MRR) was maximised. The machinability map again incorporated the key machinability characteristics: tool wear, chip control and subsurface deformation as primary points of consideration on the map, with cutting force as a secondary consideration. The map also identified a region of cutting parameters where improved chip management of Timetal 407 could be achieved. Using the high speed machining and small scale machinability experiments, mechanical twins and thermoplastic instability were identified as key determinants for chip control. The outcomes of this research were an ability to characterise machinability using a small scale experimental framework, as well as fulfilling the industry requirements through improving chip management. The improvement of chip management had a number of concurrent benefits to manufacturing operations of large structural gas turbine engine components through reducing cutting time by 43% between Ti-6Al-4V and Timetal 407, whilst also reducing cleaning downtime between parts and reducing machine maintenance to fix issues with chip swarf conveyors. The risk of component rework due to tool breakage or surface finish defects have been reduced, offering potential savings of 300 minutes per part for ‘on machine’ rework, or 480 minutes per part for ‘hand dressing’ by an operator. Due to these operational improvements, the flow of parts through manufacturing facilities has been improved, reducing inventory stock and work in progress."],"dc:format":["text"],"dc:identifier":["uk.bl.ethos.834115"],"dc:identifier.grantnumber":["EP/L016257/1"],"dc:identifier.uri":["https://etheses.whiterose.ac.uk/id/eprint/29246/1/Thesis_Chap0-6.0_v8.pdf"],"dc:language.dcterms_iso639_2":["eng"],"dc:publisher.department":["Materials Science and Engineering (Sheffield)"],"dc:publisher.institution":["University of Sheffield"],"dc:relation.isreferencedby":["https://etheses.whiterose.ac.uk/id/eprint/29246/"],"dc:relation.references":["1 C. Leyens and M. Peters, Titanium and Titanium Alloys. Wiley-VCH, 2003. 2 D. Rugg, M. Dixon, and F. P. E. Dunne, “Effective structural unit size in titanium alloys,” J. Strain Anal. Eng. Des., vol. 42, no. 4, pp. 269–279, May 2007. 3 A. A. Salem, S. R. Kalidindi, and R. D. Doherty, “Strain hardening of titanium: role of deformation twinning,” Acta Mater., vol. 51, no. 14, pp. 4225–4237, Aug. 2003. 4 A. A. Salem, S. R. Kalidindi, and R. D. Doherty, “Strain hardening regimes and microstructure evolution during large strain compression of high purity titanium,” Scr. Mater., vol. 46, no. 6, pp. 419–423, 2002. 5 A. Chapuis and J. H. Driver, “Temperature dependency of slip and twinning in plane strain compressed magnesium single crystals,” Acta Mater., vol. 59, no. 5, pp. 1986–1994, Mar. 2011. 6 A. E. Bayoumi and J. Q. Xie, “Some metallurgical aspects of chip formation in cutting Ti-6wt.%Al-4wt.%V alloy,” Mater. Sci. Eng. A, vol. 190, no. 1–2, pp. 173–180, Jan. 1995. 7 A. Fitzner, M. Thomas, J. Q. Fonseca, S. Y. Zhang, J. Kelleher, and M. Preuss, “The Effect of Aluminium on Deformation and Twinning in Alpha Titanium: The ND Case,” in Proceedings of the 13th World Conference on Titanium, Hoboken, NJ, USA: John Wiley & Sons, Inc., 2016, pp. 1051–1055. 8 A. Ghaderi and M. R. Barnett, “Sensitivity of deformation twinning to grain size in titanium and magnesium,” Acta Mater., vol. 59, no. 20, pp. 7824–7839, Dec. 2011. 9 A. Ginting and M. Nouari, “Surface integrity of dry machined titanium alloys,” Int. J. Mach. Tools Manuf., vol. 49, no. 3–4, pp. 325–332, Mar. 2009. 10 A. Gittens, “ACI’s World Airport Traffic Forecasts reveal the drivers of air transport demand growth on the path to 2040,” ACI World, 2019. [Online]. Available: https://www.internationalairportreview.com/article/106229/world-airport-traffic-forecasts-aci-world/. [Accessed: 01-May-2020]. 11 A. Hosseini and H. A. Kishawy, “Cutting Tool Materials and Tool Wear,” in Machining of Titanium Alloys, 2014, pp. 31–56. 12 A. J. Makadia and J. I. Nanavati, “Optimisation of machining parameters for turning operations based on response surface methodology,” Measurement, vol. 46, no. 4, pp. 1521–1529, 2013. 13 A. J. Wagoner Johnson, C. W. Bull, K. S. Kumar, and C. L. Briant, “The influence of microstructure and strain rate on the compressive deformation behavior of Ti-6Al-4V,” Metall. Mater. Trans. A, vol. 34, no. 2, pp. 295–306, Feb. 2003. 14 A. Jawaid, C. H. Che-Haron, and A. Abdullah, “Tool wear characteristics in turning of titanium alloy Ti-6246,” J. Mater. Process. Technol., vol. 92–93, pp. 329–334, Aug. 1999. 15 A. Kara, A. Tasdemirci, and M. Guden, “Modeling quasi-static and high strain rate deformation and failure behavior of a (±45) symmetric E-glass/polyester composite under compressive loading,” Mater. Des., vol. 49, pp. 566–574, Aug. 2013. 16 A. Molinari, C. Musquar, and G. Sutter, “Adiabatic shear banding in high speed machining of Ti–6Al–4V: experiments and modeling,” Int. J. Plast., vol. 18, no. 4, pp. 443–459, Apr. 2002. 17 A. P. Markopoulos, Finite Element Method in Machining Processes. London: Springer London, 2013. 18 A. Polishetty, M. Shunmugavel, M. Goldberg, G. Littlefair, and R. K. Singh, “Cutting Force and Surface Finish Analysis of Machining Additive Manufactured Titanium Alloy Ti-6Al-4V,” Procedia Manuf., vol. 7, pp. 284–289, Jan. 2017. 19 A. R. C. Sharman, J. I. Hughes, and K. Ridgway, “The effect of tool nose radius on surface integrity and residual stresses when turning Inconel 718TM,” J. Mater. Process. Technol., vol. 216, pp. 123–132, 2015. 20 A. R. Machado and J. Wallbank, “Machining of Titanium and its Alloys—a Review,” Proc. Inst. Mech. Eng. Part B J. Eng. Manuf., vol. 204, no. 1, pp. 53–60, 1990. 21 A. Rohatgi, K. S. Vecchio, and G. T. Gray, “The influence of stacking fault energy on the mechanical behavior of Cu and Cu-Al alloys: Deformation twinning, work hardening, and dynamic recovery,” Metall. Mater. Trans. A, vol. 32, no. 1, pp. 135–145, Jan. 2001. 22 Arrazola PJ, Garay A, Iriarte LM, et al. Machinability of titanium alloys (Ti6Al4V and Ti555.3). J Mater Process Technol 2009; 209: 2223–2230. 23 B. Chandra Behera, C. Sudarsan Ghosh, and V. R. Paruchuri, “Study of saw-tooth chip in machining of Inconel 718 by metallographic technique,” Mach. Sci. Technol., vol. 23, no. 3, pp. 431–454, May 2019. 24 B. Davis, D. Dabrow, P. Ifju, G. Xiao, S. Y. Liang, and Y. Huang, “Study of the Shear Strain and Shear Strain Rate Progression During Titanium Machining,” J. Manuf. Sci. Eng., vol. 140, no. 5, May 2018. 25 B. Mills and A. H. Redford, Machinability of Engineering Materials. Applied Science Publishers, 1983. 26 Bai W, Sun R, Roy A, et al. Improved analytical prediction of chip formation in orthogonal cutting of titanium alloy Ti6Al4V. Int J Mech Sci 2017; 133: 357–367. 27 Bäker M, Rösler J, Siemers C. The influence of thermal conductivity on segmented chip formation. In: Computational Materials Science. 2003, pp. 175–182. 28 C. Dredge, R. M’Saoubi, B. Thomas, O. Hatt, M. Thomas, and M. Jackson, “A low-cost machinability approach to accelerate titanium alloy development,” Proc. Inst. Mech. Eng. Part B J. Eng. Manuf., Jul. 2020. 29 C. Gao and L. Zhang, “Effect of cutting conditions on the serrated chip formation in high-speed machining,” Mach. Sci. Technol., vol. 17, no. 1, pp. 26–40, Jan. 2013. 30 C. H. Che-Haron and A. Jawaid, “The effect of machining on surface integrity of titanium alloy Ti-6% Al-4% v,” J. Mater. Process. Technol., vol. 166, no. 2, pp. 188-192, Aug. 2005. 31 C. H. Che-Haron, “Tool life and surface integrity in turning titanium alloy,” J. Mater. Process. Technol., vol. 118, no. 1–3, pp. 231–237, Dec. 2001. 32 C. M. Taylor, S. G. Abrego Hernandez, M. Marshall, and M. Broderick, “Cutting fluid application for titanium alloys Ti-6Al-4V and Ti-10V-2Fe-3Al in a finish turning process,” Procedia CIRP, vol. 77, pp. 441–444, 2018. 33 C. Ramirez et al., “Understanding the diffusion wear mechanisms of WC-10%Co carbide tools during dry machining of titanium alloys,” Wear, vol. 390–391, pp. 61–70, Nov. 2017. 34 C. Veiga, J. P. Davim, and A. J. R. Loureiro, “Review on machinability of titanium alloys: The process perspective,” Rev. Adv. Mater. Sci., vol. 34, no. 2, pp. 148–164, 2013. 35 C. Zheng et al., “Effect of microstructures on ballistic impact property of Ti–6Al–4V targets,” Mater. Sci. Eng. A, vol. 608, pp. 53–62, Jul. 2014. 36 Chandrasekaran H, M’saoubi R, Chazal H. Modelling of material flow stress in chip formation process from orthogonal milling and Split Hopkinson bar tests. Mach Sci Technol 2005; 9: 131–145. 37 Chen G, Ren C, Yu W, et al. Application of genetic algorithms for optimizing the Johnson–Cook constitutive model parameters when simulating the titanium alloy Ti-6Al-4V machining process. Proc Inst Mech Eng Part B J Eng Manuf 2012; 226: 1287–1297. 38 Cockroft MG, Latham DJ. Ductility and the Workability of Metals. J Inst Met 1968; 96: 33–39. 39 Cotterell M, Byrne G. Characterisation of chip formation during orthogonal cutting of titanium alloy Ti–6Al–4V. CIRP J Manuf Sci Technol 2008; 1: 81–85. 40 Cotterell M, Byrne G. Dynamics of chip formation during orthogonal cutting of titanium alloy Ti–6Al–4V. CIRP Ann 2008; 57: 93–96. 41 Crawforth P, Wynne B, Turner S, et al. Subsurface deformation during precision turning of a near-alpha titanium alloy. Scr Mater 2012; 67: 842–845. 42 D. Carou and J. P. Davim, Machining of Light Alloys. CRC Press, 2018. 43 D. G. Lee, S. Kim, S. Lee, and C. Soo Lee, “Effects of microstructural morphology on quasi-static and dynamic deformation behavior of Ti-6Al-4V alloy,” Metall. Mater. Trans. A, vol. 32, no. 2, pp. 315–324, Feb. 2001. 44 D. G. Lee, Y. H. Lee, S. Lee, C. S. Lee, and S. M. Hur, “Dynamic deformation behavior and ballistic impact properties of Ti-6Al-4V alloy having equiaxed and bimodal microstructures,” Metall. Mater. Trans. A, vol. 35, no. 10, pp. 3103–3112, Oct. 2004. 45 D. J. Truax and C. J. McMahon, “Plastic behavior of titanium-aluminum alloys,” Mater. Sci. Eng., vol. 13, no. 2, pp. 125–139, Feb. 1974. 46 D. Jeong, J. Park, S. Ahn, H. Sung, Y. Kwon, and S. Kim, “Effect of stabilization annealing on SCC susceptibility of β-annealed Ti-6Al-4V alloy in 0.6 M NaCl solution,” Met. Mater. Int., vol. 24, no. 1, pp. 101–111, Jan. 2018. 47 D. Jianxin, L. Yousheng, and S. Wenlong, “Diffusion wear in dry cutting of Ti–6Al–4V with WC/Co carbide tools,” Wear, vol. 265, no. 11, pp. 1776–1783, 2008. 48 D. K. Yang, P. Cizek, P. D. Hodgson, and C. E. Wen, “Microstructure evolution and nanograin formation during shear localization in cold-rolled titanium,” Acta Mater., vol. 58, no. 13, pp. 4536–4548, 2010. 49 D. Kuhlmann-Wilsdorf, “Theory of plastic deformation: - properties of low energy dislocation structures,” Mater. Sci. Eng. A, vol. 113, pp. 1–41, Jul. 1989. 50 D. Nguyen, D. Kang, T. Bieler, K. Park, and P. Kwon, “Microstructural impact on flank wear during turning of various Ti-6Al-4V alloys,” Wear, vol. 384–385, pp. 72–83, Aug. 2017. 51 D. R. Askeland, P. P. Fulay, and W. J. Wright, The Science and Engineering of Materials, Sixth. Global Engineering, 1984. 52 D. T. Nguyen, Y. S. Kim, and D. W. Jung, “Flow stress equations of Ti-6Al-4V titanium alloy sheet at elevated temperatures,” Int. J. Precis. Eng. Manuf., vol. 13, no. 5, pp. 747–751, May 2012. 53 D. Tromans, “Elastic Anistropy of HCP Metal Crystals and Polycrystals,” Int. J. Res. Rev. Appl. Sci., vol. 6, no. 4, pp. 462–483, 2011. 54 Devotta A, Sivaprasad P, Beno T, et al. A Modified Johnson-Cook Model for Ferritic-Pearlitic Steel in Dynamic Strain Aging Regime. Metals (Basel) 2019; 9: 528. 55 Dorogoy A, Rittel D. Determination of the Johnson – Cook Material Parameters Using the SCS Specimen. Exp Mech 2009; 49: 881. 56 E. Booser, CRC Handbook of Lubrication and Tribology, Volume III: Monitoring. CRC Press, 1993. 57 E. Levine, “Deformation mechanisms in titanium at low temperatures,” AIME MET SOC TRANS, vol. 236, no. 11, pp. 1558–1565, 1966. 58 E. M. Trent and P. K. Wright, Metal Cutting, 4th ed. 1991. 59 E. O. Ezugwu and Z. M. Wang, “Titanium alloys and their machinability—a review,” J. Mater. Process. Technol., vol. 68, no. 3, pp. 262–274, Aug. 1997. 60 E. O. Ezugwu, J. Bonney, R. B. Da Silva, and O. Çakir, “Surface integrity of finished turned Ti–6Al–4V alloy with PCD tools using conventional and high pressure coolant supplies,” Int. J. Mach. Tools Manuf., vol. 47, no. 6, pp. 884–891, 2007. 61 E. O. Hall, “The Deformation and Ageing of Mild Steel: III Discussion of Results,” Proc. Phys. Soc. Sect. B, vol. 64, no. 9, pp. 747–753, Sep. 1951. 62 F. Barlat, O. Cazacu, M. Życzkowski, D. Banabic, and J. W. Yoon, “Yield Surface Plasticity and Anisotropy,” in Continuum Scale Simulation of Engineering Materials, Weinheim, FRG: Wiley-VCH Verlag GmbH & Co. KGaA, 2005, pp. 145–183. 63 F. W. Taylor, “On the art of cutting metals”, Book, American Society of Mechanical Engineers, 1906. 64 F. Wang, J. Zhao, A. Li, and J. Zhao, “Experimental Study on Cutting Forces and Surface Integrity in High-Speed Side Milling of Ti-6Al-4V Titanium Alloy,” Mach. Sci. Technol., vol. 18, no. 3, pp. 448–463, Jul. 2014. 65 G. A. Salishchev and S. Y. Mironov, “Effect of Grain Size on Mechanical Properties of Commercially Pure Titanium,” Russ. Phys. J., vol. 44, no. 6, pp. 596–601, 2001. 66 G. E. P. Box and K. B. Wilson, “On the Experimental Attainment of Optimum Conditions,” J. R. Stat. Soc. Ser. B, vol. 13, no. 1, pp. 1–38, Jan. 1951. 67 G. Lütjering and J. C. Williams, Titanium, 2nd ed. Springer, 2007. 68 G. Lütjering, “Influence of processing on microstructure and mechanical properties of (α+β) titanium alloys,” Mater. Sci. Eng. A, pp. 32–45, 1998. 69 G. Sutter, “Chip geometries during high-speed machining for orthogonal cutting conditions,” Int. J. Mach. Tools Manuf., vol. 45, no. 6, pp. 719–726, 2005. 70 G. T. Smith, Cutting Tool Technology: Industrial Handbook. 2008. 71 Groover M. Fundamentals of Modern Manufacturing Materials, Processes and Systems. 4th Editio. John Wiley & Sons Inc, 2011. 72 Guo YB, Wen Q, Woodbury KA. Dynamic material behavior modeling using internal state variable plasticity and its application in hard machining simulations. J Manuf Sci Eng Trans ASME 2006; 128: 749–759. 73 H. Becker and W. Pantleon, “Work-hardening stages and deformation mechanism maps during tensile deformation of commercially pure titanium,” Comput. Mater. Sci., vol. 76, pp. 52–59, 2013. 74 H. E. Chandler, Metals Handbook. 1978. 75 H. J. Bunge, “The basic concepts of texture investigation in polycrystalline materials,” Steel Res., vol. 62, no. 12, pp. 530–541, Dec. 1991. 76 H. K. Toenshoff, “Machinability,” in CIRP Encyclopedia of Production Engineering, Berlin, Heidelberg: Springer Berlin Heidelberg, 2014, pp. 769–770. 77 H. M. Flower, “Microstructural development in relation to hot working of titanium alloys,” vol. 6, no. 11, pp. 1082–1092, 1990. 78 Hastings WF, Oxley PLB, Stevenson MG. Predicting a Material’s Machining Characteristics Using Flow Stress Properties Obtained from High-Speed Compression Tests. Proc Inst Mech Eng 1974; 188: 245–252. 79 Hatt O, Crawforth P, Jackson M. On the mechanism of tool crater wear during titanium alloy machining. Wear 2017; 374: 15–20. 80 Hatt O, Larsson H, Giuliani F, et al. Predicting Chemical Wear in Machining Titanium Alloys Via a Novel Low Cost Diffusion Couple Method. Procedia CIRP 2016; 45: 219–222. 81 Hatt O, Lomas Z, Thomas M, et al. The effect of titanium alloy chemistry on machining induced tool crater wear characteristics. Wear 2018; 408–409: 200–207. 82 I. Inagaki, T. Takechi, Y. Shirai, and N. Ariyasu, “Application and Features of Titanium for the Aerospace Industry,” 2014. 83 I. J. Polmear, “Titanium alloys,” in Light Alloys, Elsevier, 2005, pp. 299–365. 84 J. A. Venables, “The electron microscopy of deformation twinning,” J. Phys. Chem. Solids, vol. 25, no. 7, pp. 685–692, 1964. 85 J. C. Williams, R. G. Baggerly, and N. E. Paton, “Deformation behavior of HCP Ti-Al alloy single crystals,” Metall. Mater. Trans. A Phys. Metall. Mater. Sci., vol. 33, no. 3, pp. 837–850, 2002. 86 J. G. Schneider, “Cutting Tool Applications,” Book, ISBN-10: 0615121918, 2002. 87 J. Hou, W. Zhou, H. Duan, G. Yang, H. Xu, and N. Zhao, “Influence of cutting speed on cutting force, flank temperature, and tool wear in end milling of Ti-6Al-4V alloy,” Int. J. Adv. Manuf. Technol., vol. 70, no. 9–12, pp. 1835–1845, Feb. 2014. 88 J. Jeong, M. Alfreider, R. Konetschnik, D. Kiener, and S. H. Oh, “In-situ TEM observation of {101¯2} twin-dominated deformation of Mg pillars: Twinning mechanism, size effects and rate dependency,” Acta Mater., vol. 158, pp. 407–421, Oct. 2018. 89 J. Lindemann and L. Wagner, “Microtextural effects on mechanical properties of duplex microstructures in (α+β) titanium alloys,” Mater. Sci. Eng. A, vol. 263, no. 2, pp. 137–141, May 1999. 90 J. P. Davim, Machinability of Advanced Materials. Hoboken, NJ, USA: John Wiley & Sons, Inc., 2014. 91 J. P. Hirth, J. Lothe, and T. Mura, “Theory of Dislocations (2nd ed.),” J. Appl. Mech., vol. 50, no. 2, pp. 476–477, Jun. 1983. 92 J. Ribeiro, H. Lopes, L. Queijo, and D. Figueiredo, “Optimization of Cutting Parameters to Minimize the Surface Roughness in the End Milling Process Using the Taguchi Method,” Period. Polytech. Mech. Eng., vol. 61, no. 1, pp. 30–35, 2017. 93 J. Sun, S. Huang, T. Wang, and W. Chen, “Research on surface integrity of turning titanium alloy TB6,” Procedia CIRP, vol. 71, pp. 484–489, Jan. 2018. 94 J. W. Christian and S. Mahajan, “Deformation twinning,” Prog. Mater. Sci., vol. 39, no. 1–2, pp. 1–157, 1995. 95 J. W. Won, D. Kim, S. G. Hong, and C. S. Lee, “Anisotropy in twinning characteristics and texture evolution of rolling textured high purity alpha phase titanium,” J. Alloys Compd., vol. 683, pp. 92–99, 2016. 96 J. Zang, J. Zhao, A. Li, and J. Pang, “Serrated chip formation mechanism analysis for machining of titanium alloy Ti-6Al-4V based on thermal property,” Int. J. Adv. Manuf. Technol., vol. 98, no. 1–4, pp. 119–127, 2018. 97 J. Zhou, V. Bushlya, R. L. Peng, Z. Chen, S. Johansson, and J. E. Stahl, “Analysis of Subsurface Microstructure and Residual Stresses in Machined Inconel 718 with PCBN and Al2O3-SiCw Tools,” Procedia CIRP, vol. 13, pp. 150–155, 2014. 98 James S, Kosaka Y, Thomas R, et al. Timetal® 407: A Titanium Alloy to Enable Cost Reduction. In: Proceedings of the 13th World Conference on Titanium. 2016, pp. 721–725. 99 Johnson GR, Cook WH. Fracture characteristics of three metals subjected to various strains, strain rates, temperatures and pressures. Eng Fract Mech 1985; 21: 31–48. 100 K. Ohgo, “The adhesion mechanism of the built-up edge and the layer on the rake face of a cutting tool,” Wear, vol. 51, no. 1, pp. 117-126, 1978. 101 K. Viswanathan, S. Yadav and D. Sagapuram, “Shear bands in materials processing: Understanding the mechanics of flow localization from Zener’s time to the present,” Appl. Mech. Rev., vol. 72, no.6, pp. 17, Jan. 2021. 102 K. Zhang, K. V. Yang, S. Lim, X. Wu, and C. H. J. Davies, “Effect of the presence of macrozones on short crack propagation in forged two-phase titanium alloys,” Int. J. Fatigue, vol. 104, pp. 1–11, Nov. 2017. 103 Kay G. Failure Modeling of Titanium-6Al-4V and 2024-T3 Aluminum with the Johnson-Cook Material Model. 2002; 1–28. 104 Khan AS, Sung Suh Y, Kazmi R. Quasi-static and dynamic loading responses and constitutive modeling of titanium alloys. Int J Plast 2004; 20: 2233–2248. 105 Kiranli E. Determination of material constitutive equation of a biomedical grade Ti-6Al-4V alloy for cross-wedge rolling. Izmir Institute of Technology, 2009. 106 Kloenne Z, Viswanathan G, Thomas M, et al. A Comparative Study on the Substructure Evolution and Mechanical Properties of TIMETAL 407 and Ti-64. In: The 14th World Conference on Titanium Proceedings. 2019, pp. 1–6. 107 Komanduri R, Hou Z. On Thermoplastic Shear Instability in the Machining of a Titanium Alloy (Ti-6Al-4V). Metall Mater Trans A 2002; 33: 1–16. 108 L. B. Abhang and M. Hameedullah, “Optimization of Machining Parameters in Steel Turning Operation by Taguchi Method,” Procedia Eng., vol. 38, pp. 40–48, 2012. 109 L. Chen, T. I. El-Wardany, and W. C. Harris, “Modelling the Effects of Flank Wear Land and Chip Formation on Residual Stresses,” CIRP Ann., vol. 53, no. 1, pp. 95–98, Jan. 2004. 110 L. Marshall, “The influence of aluminium additions on titanium during machining through the application of a novel orthogonal cutting test method,” University of Sheffield, 2014. 111 L. Marshall, “The influence of aluminium additions on titanium during machining through the application of a novel orthogonal cutting test method.” PhD Thesis, Uni. of Shef., 2014, https://etheses.whiterose.ac.uk/7352/ 112 L. Marshall, B. Wynne, S. Turner, and M. Jackson, “Influence of Aluminium Content on the Machinability and Subsurface Deformation Of Titanium Alloys,” in Proceedings of the 13th World Conference on Titanium, Hoboken, NJ, USA: John Wiley & Sons, Inc., 2016, pp. 923–928. 113 Laakso SVA, Niemi E. Determination of material model parameters from orthogonal cutting experiments. Proc Inst Mech Eng Part B J Eng Manuf 2016; 230: 848–857. 114 Lee W, Lin C. High-temperature deformation behaviour of Ti6Al4V alloy evaluated by high strain-rate compression tests. J Mater Process Technol 1998; 75: 127–136. 115 Lee W, Lin C. Plastic deformation and fracture behaviour of Ti–6Al–4V alloy loaded with high strain rate under various temperatures. Mater Sci Eng A 1998; 241: 48–59. 116 Lütjering G, Williams JC. Titanium. 2nd ed. Springer, 2007. 117 M. Aceves-Lopez, “Subsurface deformation micro-mechanisms induced during machining of titanium alloys at low temperatures, and a new method to examine their machining behaviour,” University of Sheffield, 2018. 118 M. Ahmed, D. Wexler, G. Casillas, D. G. Savvakin, and E. V. Pereloma, “Strain rate dependence of deformation-induced transformation and twinning in a metastable titanium alloy,” Acta Mater., vol. 104, pp. 190–200, Feb. 2016. 119 M. Armendia, A. Garay, L. M. Iriarte, and P. J. Arrazola, “Comparison of the machinabilities of Ti6Al4V and TIMETAL® 54M using uncoated WC–Co tools,” J. Mater. Process. Technol., vol. 210, no. 2, pp. 197–203, Jan. 2010. 120 M. Armendia, P. Osborne, A. Garay, J. Belloso, S. Turner, and P. Arrazola, “Influence of Heat Treatment on the Machinability of Titanium Alloys,” Mater. Manuf. Process., vol. 27, no. 4, pp. 457–461, 2012. 121 M. Arul Kumar, M. Wroński, R. J. McCabe, L. Capolungo, K. Wierzbanowski, and C. N. Tomé, “Role of microstructure on twin nucleation and growth in HCP titanium: A statistical study,” Acta Mater., vol. 148, pp. 123–132, 2018. 122 M. Bache, H. Davies, W. Davey, M. Thomas, and I. Berment-Parr, “Microstructural Control of Fatigue Behaviour in a Novel alpha+beta Titanium Alloy,” Metals (Basel)., vol. 9, no. 11, p. 1200, Nov. 2019. 123 M. Battaini, “Deformation Behaviour and Twinning Mechanisms of Commercially Pure Titanium Alloys,” Monash University, 2008. 124 M. Cotterell and G. Byrne, “Dynamics of chip formation during orthogonal cutting of titanium alloy Ti–6Al–4V,” CIRP Ann., vol. 57, no. 1, pp. 93–96, Jan. 2008. 125 M. D. F. Rahman, “Stress and Strain Distributions during Machining of Ti-6Al-4V at Ambient and Cryogenic Temperatures,” University of Windsor, 2014. 126 M. Donachie Jr., Titanium – A Technical Guide, 2nd ed. 2000. 127 M. E. Merchant, “Mechanics of the metal cutting process. I. Orthogonal cutting and a type 2 chip,” J. Appl. Phys., Vol. 16, no. 5, 1945, https://doi.org/10.1063/1.1707586. 128 M. Groover, Fundamentals of Modern Manufacturing Materials, Processes and Systems, 4th Editio. John Wiley & Sons Inc, 2011. 129 M. H. Miguélez, X. Soldani, and A. Molinari, “Analysis of adiabatic shear banding in orthogonal cutting of Ti alloy,” Int. J. Mech. Sci., vol. 75, pp. 212–222, Oct. 2013. 130 M. Jackson and R. R. Boyer, “Titanium and its Alloys: Processing, Fabrication and Mechanical Performance,” Encycl. Aerosp. Eng., vol. 9, no. 6, p. 689, Dec. 2010. 131 M. Nalbant, H. Gökkaya, and G. Sur, “Application of Taguchi method in the optimization of cutting parameters for surface roughness in turning,” Mater. Des. vol. 28, no. 4, pp. 1379–1385, Jan. 2007. 132 M. Peters, J. Kumpfert, C. H. Ward, and C. Leyens, “Titanium Alloys for Aerospace Applications,” Adv. Eng. Mater., vol. 5, no. 6, pp. 419–427, Jun. 2003. 133 M. Thomas, S. Turner, and M. Jackson, “Microstructural damage during high-speed milling of titanium alloys,” Scr. Mater., vol. 62, no. 5, pp. 250–253, 2010. 134 Macdougall DAS, Harding J. A constitutive relation and failure criterion for Ti6Al4V alloy at impact rates of strain. J Mech Phys Solids 1999; 47: 1157–1185. 135 Machado AR, Wallbank J. Machining of Titanium and its Alloys—a Review. Proc Inst Mech Eng Part B J Eng Manuf 1990; 204: 53–60. 136 Marshall L, Wynne B, Turner S, et al. Influence of Aluminium Content on the Machinability and Subsurface Deformation Of Titanium Alloys. In: Proceedings of the 13th World Conference on Titanium. Hoboken, NJ, USA: John Wiley & Sons, Inc., pp. 923–928. 137 Marshall L. The influence of aluminium additions on titanium during machining through the application of a novel orthogonal cutting test method. University of Sheffield, 2014. 138 Meyer HW, Kleponis DS. Modeling the high strain rate behavior of titanium undergoing ballistic impact and penetration. Int J Impact Eng 2001; 26: 509–521. 139 Miguélez MH, Soldani X, Molinari A. Analysis of adiabatic shear banding in orthogonal cutting of Ti alloy. Int J Mech Sci 2013; 75: 212–222. 140 Miguélez MH, Zaera R, Molinari A, et al. Residual Stresses in Orthogonal Cutting of Metals: The Effect of Thermomechanical Coupling Parameters and of Friction. J Therm Stress 2009; 32: 269–289. 141 Molinari A, Musquar C, Sutter G. Adiabatic shear banding in high speed machining of Ti–6Al–4V: experiments and modeling. Int J Plast 2002; 18: 443–459. 142 N. C. Tsourveloudis, “Predictive Modeling of the Ti6Al4V Alloy Surface Roughness,” J. Intell. Robot. Syst., vol. 60, no. 3–4, pp. 513–530, Dec. 2010. 143 N. Fang and Q. Wu, “A comparative study of the cutting forces in high speed machining of Ti–6Al–4V and Inconel 718 with a round cutting edge tool,” J. Mater. Process. Technol., vol. 209, no. 9, pp. 4385–4389, May 2009. 144 N. Gey, P. Bocher, E. Uta, L. Germain, and M. Humbert, “Texture and microtexture variations in a near-α titanium forged disk of bimodal microstructure,” Acta Mater., vol. 60, no. 6, pp. 2647–2655, 2012. 145 N. J. Petch and J. Iron, “The cleavage strength of polycrystals,” Steel Inst., vol. 173, pp. 25–28, 1953. 146 N. Khanna and K. S. Sangwan, “Comparative machinability study on Ti54M titanium alloy in different heat treatment conditions,” Proc. Inst. Mech. Eng. Part B J. Eng. Manuf., vol. 227, no. 1, pp. 96–101, Jan. 2013. 147 N. Khanna and K. S. Sangwan, “Machinability analysis of heat treated Ti64, Ti54M and Ti10.2.3 titanium alloys,” Int. J. Precis. Eng. Manuf., vol. 14, no. 5, pp. 719–724, May 2013. 148 N. Khanna, A. Garay, L. M. Iriarte, D. Soler, K. S. Sangwan, and P. J. Arrazola, “Effect of heat Treatment Conditions on the Machinability of Ti64 and Ti54M Alloys,” Procedia CIRP, vol. 1, pp. 477–482, 2012. 149 N. Narutaki, A. Murakoshi, S. Motonishi, and H. Takeyama, “Study on Machining of Titanium Alloys,” CIRP Ann., vol. 32, no. 1, pp. 65–69, Jan. 1983. 150 N. P. Gurao, R. Kapoor, and S. Suwas, “Deformation behaviour of commercially pure titanium at extreme strain rates,” Acta Mater., vol. 59, no. 9, pp. 3431–3446, 2011. 151 N. Tomac, K. Sørby, and S. Doboviček, “Formation of built-up layer on the tool in turning operation of magnesium alloys,” Teh. Vjesn., vol. 25, no. 3, pp. 940–943, 2018. 152 Nasr M, Ng E, Elbestawi M. Effects of workpiece thermal properties on machining-induced residual stresses - thermal softening and conductivity. Proc Inst Mech Eng Part B J Eng Manuf 2007; 221: 1387–1400. 153 Nemat-Nasser S, Guo WG, Nesterenko VF, et al. Dynamic response of conventional and hot isostatically pressed Ti–6Al–4V alloys: experiments and modeling. Mech Mater 2001; 33: 425–439. 154 O. Engler and V. Randle, Introduction to Texture Analysis; Macrotexture, microtexture, and orientation mapping. CRC Press, 2009. 155 O. Hatt, H. Larsson, F. Giuliani, P. Crawforth, B. Wynne, and M. Jackson, “Predicting Chemical Wear in Machining Titanium Alloys Via a Novel Low Cost Diffusion Couple Method,” Procedia CIRP, vol. 45, pp. 219–222, 2016. 156 O. Hatt, P. Crawforth, and M. Jackson, “On the mechanism of tool crater wear during titanium alloy machining,” Wear, vol. 374, pp. 15–20, 2017. 157 Odelros S, Kaplan B, Kritikos M, et al. Experimental and theoretical study of the microscopic crater wear mechanism in titanium machining. Wear 2017; 376–377: 115–124. 158 Oliaei SNB, Karpat Y. Built-up edge effects on process outputs of titanium alloy micro milling. Precis Eng 2017; 49: 305–315. 159 Oliaei SNB, Karpat Y. Investigating the influence of built-up edge on forces and surface roughness in micro scale orthogonal machining of titanium alloy Ti6Al4V. J Mater Process Technol 2016; 235: 28–40. 160 Oxley PLB. The Mechanics of machining: An analytical approach to assessing machinability. Halsted Press, 1989. 161 P. A. Dearnley and A. N. Grearson, “Evaluation of principal wear mechanisms of cemented carbides and ceramics used for machining titanium alloy IMI 318,” Mater. Sci. Technol., vol. 2, no. 1, pp. 47–58, Jan. 1986. 162 P. Davies, R. Thomas, P. Garratt, N. Green, M. Coleman, and S. Birosca, “The Effect of Elevated Temperature Exposure on the Mechanical Properties of Ti834,” in Proceedings of the 13th World Conference on Titanium, Hoboken, NJ, USA: John Wiley & Sons, Inc., 2016, pp. 1625–1630. 163 P. Dobroň, F. Chmelík, S. Yi, K. Parfenenko, D. Letzig, and J. Bohlen, “Grain size effects on deformation twinning in an extruded magnesium alloy tested in compression,” Scr. Mater., vol. 65, no. 5, pp. 424–427, 2011. 164 P. G. Partridge, “Cyclic twinning in fatigued close-packed hexagonal metals,” Philos. Mag. A J. Theor. Exp. Appl. Phys., vol. 12, no. 119, pp. 1043–1054, Nov. 1965. 165 P. G. Partridge, “The crystallography and deformation modes of hexagonal close-packed metals,” Metall. Rev., vol. 12, no. 1, pp. 169–194, Jan. 1967. 166 P. J. Arrazola, A. Garay, L. M. Iriarte, M. Armendia, S. Marya, and F. Le Maître, “Machinability of titanium alloys (Ti6Al4V and Ti555.3),” J. Mater. Process. Technol., vol. 209, no. 5, pp. 2223–2230, 2009. 167 Polishetty A, Shunmugavel M, Goldberg M, et al. Cutting Force and Surface Finish Analysis of Machining Additive Manufactured Titanium Alloy Ti-6Al-4V. Procedia Manuf 2017; 7: 284–289. 168 Q. Wang and Z. Liu, “Plastic deformation induced nano-scale twins in Ti-6Al-4V machined surface with high speed machining,” Mater. Sci. Eng. A, vol. 675, pp. 271–279, Oct. 2016. 169 R. Ding, J. Gong, A. J. Wilkinson, and I. P. Jones, “〈c+a〉 Dislocations in deformed Ti–6Al–4V micro-cantilevers,” Acta Mater., vol. 76, pp. 127–134, 2014. 170 R. K. Gupta, C. Mathew, and P. Ramkumar, “Strain Hardening in Aerospace Alloys,” Front. Aerosp. Eng., vol. 4, no. 1, pp. 1–13, 2015. 171 R. Komanduri and B. F. Von Turkovich, “New observations on the mechanism of chip formation when machining titanium alloys,” Wear, vol. 69, no. 2, pp. 179–188, Jun. 1981. 172 R. Komanduri and Z. Hou, “On Thermoplastic Shear Instability in the Machining of a Titanium Alloy (Ti-6Al-4V),” Metall. Mater. Trans. A, vol. 33, no. 9, pp. 1–16, 2002. 173 R. Lalbondre, P. Krishna, and G. C. Mohankumar, “An Experimental Investigation on Machinability Studies of Steels by Face Turning,” Procedia Mater. Sci., vol. 6, pp. 1386–1395, 2014. 174 R. Reed-Hill and R. Abbaschian, Physical Metallurgy Principles, 3rd ed. Boston: International Thomson Publishing, 1994. 175 R. V. Mises, “Mechanik der plastischen Formänderung von Kristallen,” ZAMM - Zeitschrift für Angew. Math. und Mech., vol. 8, no. 3, pp. 161–185, 1928. 176 R. Wanhill and S. Barter, Fatigue of Beta Processed and Beta Heat-treated Titanium Alloys. Dordrecht: Springer Netherlands, 2012. 177 R. Y. Y. Ma, Q. Xue, H. Wang, S. Huang, J. Qiu, X. Feng, J. Lei, “Deformation Twinning in Fatigue Crack Tip Plastic Zone of Ti-6al-4v Alloy with Widmanstatten Microstructure,” Mater. Charact., vol. 132, pp. 338–347, 2017. 178 Ramaswami R. The effect of the built-up-edge (BUE) on the wear of cutting tools. Wear 1971; 18: 1–10. 179 S. A. Niknam, R. Khettabi, and V. Songmene, “Machinability and Machining of Titanium Alloys: A Review,” in Materials Forming, Machining and Tribology, 2014, pp. 1–30. 180 S. H. Rhim and S. I. Oh, “Prediction of serrated chip formation in metal cutting process with new flow stress model for AISI 1045 steel,” J. Mater. Process. Technol., vol. 171, no. 3, pp. 417–422, Feb. 2006. 181 S. I. Jaffery and P. T. Mativenga, “Assessment of the machinability of Ti-6Al-4V alloy using the wear map approach,” Int. J. Adv. Manuf. Technol., vol. 40, no. 7–8, pp. 687–696, 2009. 182 S. J. Sun, M. Brandt, and J. P. T. Mo, “Effect of Microstructure on Cutting Force and Chip Formation during Machining of Ti-6Al-4V Alloy,” Adv. Mater. Res., vol. 690–693, pp. 2437–2441, May 2013. 183 S. James, Y. Kosaka, R. Thomas, and P. Garratt, “Timetal® 407: A Titanium Alloy to Enable Cost Reduction,” in Proceedings of the 13th World Conference on Titanium, 2016, pp. 721–725. 184 S. Nemat-Nasser, W. G. Guo, and J. Y. Cheng, “Mechanical properties and deformation mechanisms of a commercially pure titanium,” Acta Mater., vol. 47, no. 13, pp. 3705–3720, Oct. 1999. 185 S. Ramesh, L. Karunamoorthy, and K. Palanikumar, “Surface Roughness Analysis in Machining of Titanium Alloy,” Mater. Manuf. Process., vol. 23, no. 2, pp. 174–181, Jan. 2008. 186 S. Sun, M. Brandt, and M. S. Dargusch, “Characteristics of cutting forces and chip formation in machining of titanium alloys,” Int. J. Mach. Tools Manuf., 2009. 187 S. Sun, M. Brandt, and M. S. Dargusch, “Characteristics of cutting forces and chip formation in machining of titanium alloys,” Int. J. Mach. Tools Manuf., vol. 49, no.7-8, pp. 561-568, June. 2009. 188 S. V. Telrandhe, A. K. Saxena, and S. Mishra, “Effect of microstructure and cutting speed on machining behavior of Ti6Al4V alloy,” J. Mech. Sci. Technol., vol. 31, no. 5, pp. 2177–2184, May 2017. 189 S. Zhang, J. Li, X. Zhu, and H. Lv, “Saw-tooth chip formation and its effect on cutting force fluctuation in turning of Inconel 718,” Int. J. Precis. Eng. Manuf., vol. 14, no. 6, pp. 957–963, Jun. 2013. 190 Salem AA, Kalidindi SR, Doherty RD. Strain hardening of titanium: role of deformation twinning. Acta Mater 2003; 51: 4225–4237. 191 Salem AA, Kalidindi SR, Doherty RD. Strain hardening regimes and microstructure evolution during large strain compression of high purity titanium. Scr Mater 2002; 46: 419–423. 192 Scientific Forming Technologies. DEFORM v11.2. 193 Seo S, Min O, Yang H. Constitutive equation for Ti – 6Al – 4V at high temperatures measured using the SHPB technique. Int J Impact Eng 2005; 31: 735–754. 194 Shatla M, Kerk C, Altan T. Process modeling in machining. Part I: determination of flow stress data. Int J Mach Tools Manuf 2001; 41: 1511–1534. 195 Shrot A, Bäker M. Determination of Johnson–Cook parameters from machining simulations. Comput Mater Sci 2012; 52: 298–304. 196 Storchak, Rupp, Möhring, et al. Determination of Johnson–Cook Constitutive Parameters for Cutting Simulations. Metals (Basel) 2019; 9: 473. 197 Sutter G. Chip geometries during high-speed machining for orthogonal cutting conditions. Int J Mach Tools Manuf 2005; 45: 719–726. 198 T. B. Britton, F. P. E. Dunne, and A. J. Wilkinson, “On the mechanistic basis of deformation at the microscale in hexagonal close-packed metals,” Proc. R. Soc. A Math. Phys. Eng. Sci., vol. 471, no. 2178, 2015. 199 T. Bakša, T. Kroupa, P. Hanzl, and M. Zetek, “Durability of Cutting Tools during Machining of Very Hard and Solid Materials,” Procedia Eng., vol. 100, pp. 1414–1423, 2015. 200 T. Childs, “Metal Machining Theory and Applications,” Mater. Technol., pp. 1–19, 2000. 201 T. Özel and D. Ulutan, “Prediction of machining induced residual stresses in turning of titanium and nickel based alloys with experiments and finite element simulations,” CIRP Ann., vol. 61, no. 1, pp. 547–550, Jan. 2012. 202 T. Sugahara et al., “The effect of Widmanstätten and equiaxed microstructures of Ti-6Al-4V on the oxidation rate and creep behavior,” Mater. Sci. Forum, vol. 636–637, no. June 2014, pp. 657–662, 2010. 203 Thomas M, Turner S, Jackson M. Microstructural damage during high-speed milling of titanium alloys. Scr Mater 2010; 62: 250–253. 204 V. Sinha, M. J. Mills, J. C. Williams, and J. E. Spowart, “Observations on the faceted initiation site in the dwell-fatigue tested Ti-6242 alloy: Crystallographic orientation and size effects,” Metall. Mater. Trans. A, vol. 37, no. 5, pp. 1507–1518, May 2006. 205 W. D. Callister and D. G. Rethwisch, Materials Science and Engineering: An Introduction, 8th ed. Wiley, 2009. 206 W. Davey, M. Bache, H. Davies, and M. Thomas, “Fatigue Performance of the Novel Titanium Alloy Timetal 407,” MATEC Web Conf., vol. 165, p. 4001, May 2018. 207 W. Min, W. Min, and Z. Youzhen, “Diffusion wear in milling titanium alloys,” Mater. Sci. Technol., vol. 4, no. 6, pp. 548–553, Jun. 1988. 208 W. P. Koster, M. Field, L. Fritz, L. R. Gatto, and J. F. Kahles, “Surface Integrity of Machined Structural Components,” Technic. Report, 1970, https://apps.dtic.mil/sti/citations/AD0870146 209 W. Seo, D. Jeong, D. Lee, H. Sung, Y. Kwon, and S. Kim, “Effects of cooling rate and stabilization annealing on fatigue behavior of β-processed Ti-6Al-4V alloys,” Met. Mater. Int., vol. 23, no. 4, pp. 648–659, Jul. 2017. 210 Wyen C, Wegener K. Influence of cutting edge radius on cutting forces in machining titanium. CIRP Ann 2010; 59: 93–96. 211 X. Tan, H. Guo, H. Gu, C. Laird, and N. D. H. Munroe, “Cyclic deformation behavior of high-purity titanium single crystals: Part II. Microstructure and mechanism,” Metall. Mater. Trans. A, vol. 29, no. 2, pp. 513–518, Feb. 1998. 212 X. Yang and C. R. Liu, “Machining titanium and its alloys,” Mach. Sci. Technol., vol. 3, no. 1, pp. 107–139, 1999. 213 Y. B. Chun, S. H. Yu, S. L. Semiatin, and S. K. Hwang, “Effect of deformation twinning on microstructure and texture evolution during cold rolling of CP-titanium,” Mater. Sci. Eng. A, vol. 398, no. 1, pp. 209–219, 2005. 214 Y. B. Egorova, A. A. Il’in, B. A. Kolachev, V. K. Nosov, and A. M. Mamonov, “Effect of the Structure on the Cutability of Titanium Alloys,” Met. Sci. Heat Treat., vol. 45, no. 4, pp. 16–21, 2003. 215 Y. H. Çelik and A. Karabiyik, “Effect of cutting parameters on machining surface and cutting tool in milling of Ti-6Al-4V alloy,” Indian J. Eng. Mater. Sci., vol. 23, no. 5, pp. 349–356, 2016. 216 Y. Kosaka and S. P. Fox, “Influence of alloy chemistry and microstructure on the machinability of titanium alloys,” in Cost-Affordable Titanium: A Symposium Dedicated to Professor Harvey Flower as held at the 2004 TMS Annual Meeting, 2004, pp. 169–176. 217 Y. Kosaka, J. C. Fanning, and S. P. Fox, “Development of low cost high strength alpha/ beta alloy with superior machinability,” in Proceedings of the 10th World Conference on Titanium, 2004, pp. 3028–3034. 218 Y. Seo, S. C. Woo, T. W. Kim, and Y. S. Lee, “Influence of heat treated microstructures on the dynamic deformation characteristics of Ti-6Al-4V alloy,” J. Mech. Sci. Technol., vol. 29, no. 12, pp. 5223–5232, Dec. 2015. 219 Y. T. Zhu, X. Z. Liao, X. L. Wu, and J. Narayan, “Grain size effect on deformation twinning and detwinning,” J. Mater. Sci., vol. 48, no. 13, pp. 4467–4475, Jul. 2013. 220 Y. Xu, J. Zhang, Y. Bai, and M. A. Meyers, “Shear Localization in Dynamic Deformation: Microstructural Evolution,” Metall. Mater. Trans. A, vol. 39, no. 4, pp. 811–843, Apr. 2008. 221 Z. Chen et al., “Effect of thermal exposure on microstructure and nano-hardness of broached Inconel 718,” MATEC Web Conf., vol. 14, p. 08002, Aug. 2014. 222 Z. Kloenne, G. Viswanathan, M. Thomas, M. Loretto, and H. Fraser, “A Comparative Study on the Substructure Evolution and Mechanical Properties of TIMETAL 407 and Ti-64,” in The 14th World Conference on Titanium Proceedings, 2019, pp. 1–6. 223 Z. Li, J. Li, Y. Zhu, X. Tian, and H. Wang, “Variant selection in laser melting deposited α + β titanium alloy,” J. Alloys Compd., vol. 661, pp. 126–135, 2016. 224 Z. W. Huang, P. L. Yong, H. Zhou, and Y. S. Li, “Grain size effect on deformation mechanisms and mechanical properties of titanium,” Mater. Sci. Eng. A, vol. 773, p. 138721, 2020. 225 Z. W. Wyatt, W. J. Joost, D. Zhu, and S. Ankem, “Deformation mechanisms and kinetics of time-dependent twinning in an α-titanium alloy,” Int. J. Plast., vol. 39, pp. 119–131, Dec. 2012. 226 Zhou J, Ren J, Jiang Y. Inverse identification of modified Johnson–Cook model for cutting titanium alloy Ti6Al4V using firefly algorithm. Proc Inst Mech Eng Part B J Eng Manuf 2020; 234: 584–599."],"dcterms:accessrights":["public"],"dc:title":["Evaluating the Machinability of Titanium Alloys, Timetal 407 and Ti-6Al-4V"],"dc:type":["Thesis"],"dc:type.qualificationlevel":["doctoral"],"dc:type.qualificationname":["Eng.D"],"person:identifier.orcid":["000000029479343X"]},"updated_at":"2026-11-18T22:43:01Z"}