No description available.

No

Yes / In this work, a highly instrumented single screw extruder has been used to study the effect of polymer rheology on the thermal efficiency of the extrusion process. Three different molecular weight grades of high density polyethylene (HDPE) were extruded at a range of conditions. Three geometries of extruder screws were used at several set temperatures and screw rotation speeds. The extruder was equipped with real-time quantification of energy consumption; thermal dynamics of the process were examined using thermocouple grid sensors at the entrance to the die. Results showed that polymer rheology had a significant effect on process energy consumption and thermal homogeneity of the melt. Highest specific energy consumption and poorest homogeneity was observed for the highest viscosity grade of HDPE. Extruder screw geometry, set extrusion temperature and screw rotation speed were also found to have a direct effect on energy consumption and melt consistency. In particular, specific energy consumption was lower using a barrier flighted screw compared to single flighted screws at the same set conditions. These results highlight the complex nature of extrusion thermal dynamics and provide evidence that rheological properties of the polymer can significantly influence the thermal efficiency of the process. (C) 2014 The Authors. Published by Elsevier B.V. All rights reserved.

In the polymer extrusion process the product quality like mechanical, optical, electrical properties and homogeneity etc. can be achieved by controlling the melt temperature, melt pressure or viscosity within a narrow fluctuation range. In the earlier studies there are many literatures in connection with the extrusion quality and related quality controls; i.e. temperature control, pressure control and viscosity control. In each of the control strategies, it is believed that the most effective to maintain product quality utilising viscosity control, because a polymer viscosity closely correlates with its composition and molecular distribution, and hence the characteristic of the material. In the viscosity control strategy, viscosity is an induced variable calculated from either the (1) flow rate and pressure drop with in-line rheometer or (2) melt temperature, screw speed (or pressure), geometrical dimensions of extruder, and extrusion material constants without in-line rheometer; the former method may interfere the output rate while the latter one does not. On the demand of using viscosity-measuring instruments as sensors to control the quality of the products, we developed an empirical off-line viscosity model, which is used to derive the extrusion viscosity models in the control process without in-line rheometer. The off-line viscosity model is proved more accuracy than other previous suggested models, such as WLF and Andrade¡¦s equations, to fit the experimental data. Polypropylene (PP) was used in this study to test the effectiveness of the extrusion viscosity models. Comparing the calculated results, it was found that the viscosity characteristics obtained by the extrusion viscosity models are in agreement with those obtained by using an in-line rheometer. Both methods can be used to obtain the viscosity in the polymer extrusion process. The objective of this study is to develop extrusion viscosity models together with collected data from several experimental tests and template rule-base to build a Multi-Input Multi-Output (MIMO) fuzzy logic closed-loop controller for the plastics extrusion control. The objective of this controller is to eliminate process variations and to produce the polymer of consistent quality. The fuzzy logic is provided for designing the MIMO closed-loop controller because it is suitable for applying to the polymer extrusion process control with such advantages as handling complex problems like non-linear, time varying behaviour and poor quality measurements happened in the extrusion process, etc. The experimental pre-tests include (1) investigation of the relationship between melt temperature and barrel setting temperatures (2) investigation of the relationship between melt pressure and screw speed and (3) building the relation equation between measured viscosity, melt temperature and speed for the in-line rheometer, etc. In order to test the effectiveness of the MIMO FLC, an off-line simulation program is developed, and the closed-loop tests are performed on the extruder. The test results prove that the designed MIMO FLC can effectively control the quality of products.

No description available.

Polymer extrusion is an energy intensive process whereby the simultaneous action of viscous shear and thermal conduction are used to convert solid polymer to a melt which can be formed into a shape. To optimise efficiency, a homogeneous melt is required with minimum consumption of process energy. In this work, in-process monitoring techniques have been used to characterise the thermal dynamics of the single screw extrusion process with real-time quantification of energy consumption. Thermocouple grid sensors were used to measure radial melt temperatures across the melt flow at the entrance to the extruder die. Moreover, an infrared sensor flush mounted at the end of the extruder barrel was used to measure non-invasive melt temperature profiles across the width of the screw channel in the metering section of the extruder screw. Both techniques were found to provide useful information concerning the thermal dynamics of the extrusion process; in particular this application of infrared thermometry could prove useful for industrial extrusion process monitoring applications. Extruder screw geometry and extrusion variables should ideally be tailored to suit the properties of individual polymers but in practise this is rarely achieved due the lack of understanding. Here, LDPE, LLDPE, three grades of HDPE, PS, PP and PET were extruded using three geometries of extruder screws at several set temperatures and screw rotation speeds. Extrusion data showed that polymer rheology had a significant effect on the thermal efficiency on the extrusion process. In particular, melt viscosity was found to have a significant effect on specific energy consumption and thermal homogeneity of the melt. Extruder screw geometry, set extrusion temperature and screw rotation speed were also found to have a direct effect on energy consumption and melt consistency. Single flighted extruder screws exhibited poorer temperature homogeneity and larger fluctuations than a barrier flighted screw with a spiral mixer. These results highlighted the importance of careful selection of processing conditions and extruder screw geometry on melt homogeneity and process efficiency. Extruder scale was found to have a significant influence on thermal characteristics due to changes in surface area of the screw, barrel and heaters which consequently affect the effectiveness of the melting process and extrusion process energy demand. In this thesis, the thermal and energy characteristics of two single screw extruders were compared to examine the effect of extruder scale and processing conditions on measured melt temperature and energy consumption. Extrusion thermal dynamics were shown to be highly dependent upon extruder scale whilst specific energy consumption compared more favourably, enabling prediction of a process window from lab to industrial scale within which energy efficiency can be optimised. Overall, this detailed experimental study has helped to improve understanding of the single screw extrusion process, in terms of thermal stability and energy consumption. It is hoped that the findings will allow those working in this field to make more informed decisions regarding set conditions, screw geometry and extruder scale, in order to improve the efficiency of the extrusion process.

Yes / Polymer extrusion is an important but an energy intensive method of processing polymeric materials. The rapid increase in demand of polymeric products has forced manufactures to rethink their processing efficiencies to manufacture good quality products with low-unit-cost. Here, analyzing the operational conditions has become a key strategy to achieve both energy and thermal efficiencies simultaneously. This study aims to explore the effects of polymers' rheology on the energy consumption and melt thermal quality (ie, a thermally homogeneous melt flow in both radial and axil directions) of extruders. Six commodity grades of polymers (LDPE, LLDPE, PP, PET, PS, and PMMA) were processed at different conditions in two types of continuous screw extruders. Total power, motor power, and melt temperature profiles were analyzed in an industrial scale single-screw extruder. Moreover, the active power (AP), mass throughput, torque, and power factor were measured in a laboratory scale twin-screw extruder. The results confirmed that the specific energy consumption for both single and twin screw extruders tends to decrease with the processing speed. However, this action deteriorates the thermal stability of the melt regardless the nature of the polymer. Rheological characterization results showed that the viscosity of LDPE and PS exhibited a normal shear thinning behavior. However, PMMA presented a shear thickening behavior at moderate-to-high shear rates, indicating the possible formation of entanglements. Overall, the findings of this work confirm that the materials' rheology has an appreciable correlation with the energy consumption in polymer extrusion and also most of the findings are in agreement with the previously reported investigations. Therefore, further research should be useful for identifying possible correlations between key process parameters and hence to further understand the processing behavior for wide range of machines, polymers, and operating conditions.

Yes / Extrusion is one of the fundamental production methods in the polymer processing industry and is used in the production of a large number of commodities in a diverse industrial sector. Being an energy intensive production method, process energy efficiency is one of the major concerns and the selection of the most energy efficient processing conditions is a key to reducing operating costs. Usually, extruders consume energy through the drive motor, barrel heaters, cooling fans, cooling water pumps, gear pumps, etc. Typically the drive motor is the largest energy consuming device in an extruder while barrel/die heaters are responsible for the second largest energy demand. This study is focused on investigating the total energy demand of an extrusion plant under various processing conditions while identifying ways to optimise the energy efficiency. Initially, a review was carried out on the monitoring and modelling of the energy consumption in polymer extrusion. Also, the power factor, energy demand and losses of a typical extrusion plant were discussed in detail. The mass throughput, total energy consumption and power factor of an extruder were experimentally observed over different processing conditions and the total extruder energy demand was modelled empirically and also using a commercially available extrusion simulation software. The experimental results show that extruder energy demand is heavily coupled between the machine, material and process parameters. The total power predicted by the simulation software exhibits a lagging offset compared with the experimental measurements. Empirical models are in good agreement with the experimental measurements and hence these can be used in studying process energy behaviour in detail and to identify ways to optimise the process energy efficiency.

Polymer extrusion is an energy intensive process whereby the simultaneous action of viscous shear and thermal conduction are used to convert solid polymer to a melt which can be formed into a shape. To optimise efficiency, a homogeneous melt is required with minimum consumption of process energy. In this work, in-process monitoring techniques have been used to characterise the thermal dynamics of the single screw extrusion process with real-time quantification of energy consumption. Thermocouple grid sensors were used to measure radial melt temperatures across the melt flow at the entrance to the extruder die. Moreover, an infrared sensor flush mounted at the end of the extruder barrel was used to measure non-invasive melt temperature profiles across the width of the screw channel in the metering section of the extruder screw. Both techniques were found to provide useful information concerning the thermal dynamics of the extrusion process; in particular this application of infrared thermometry could prove useful for industrial extrusion process monitoring applications. Extruder screw geometry and extrusion variables should ideally be tailored to suit the properties of individual polymers but in practise this is rarely achieved due the lack of understanding. Here, LDPE, LLDPE, three grades of HDPE, PS, PP and PET were extruded using three geometries of extruder screws at several set temperatures and screw rotation speeds. Extrusion data showed that polymer rheology had a significant effect on the thermal efficiency on the extrusion process. In particular, melt viscosity was found to have a significant effect on specific energy consumption and thermal homogeneity of the melt. Extruder screw geometry, set extrusion temperature and screw rotation speed were also found to have a direct effect on energy consumption and melt consistency. Single flighted extruder screws exhibited poorer temperature homogeneity and larger fluctuations than a barrier flighted screw with a spiral mixer. These results highlighted the importance of careful selection of processing conditions and extruder screw geometry on melt homogeneity and process efficiency. Extruder scale was found to have a significant influence on thermal characteristics due to changes in surface area of the screw, barrel and heaters which consequently affect the effectiveness of the melting process and extrusion process energy demand. In this thesis, the thermal and energy characteristics of two single screw extruders were compared to examine the effect of extruder scale and processing conditions on measured melt temperature and energy consumption. Extrusion thermal dynamics were shown to be highly dependent upon extruder scale whilst specific energy consumption compared more favourably, enabling prediction of a process window from lab to industrial scale within which energy efficiency can be optimised. Overall, this detailed experimental study has helped to improve understanding of the single screw extrusion process, in terms of thermal stability and energy consumption. It is hoped that the findings will allow those working in this field to make more informed decisions regarding set conditions, screw geometry and extruder scale, in order to improve the efficiency of the extrusion process. / Engineering and Physical Sciences Research Council

This thesis presents a model for the procedures of manufacturing Fused Filament Fabrication (FFF) components by calculating required process parameters using empirical equations. Such an empirical model has been required within the FFF field of research for a considerable amount of time and will allow for an expansion in understanding of the fundamental mathematics of FFF. Data acquired through experimentation has allowed for a data set of geometric characteristics to be built up and used to validate the model presented. The research presented draws on previous literature in the fields of additive manufacturing, machine engineering, tool-path programming, polymer science and rheology. Combining these research fields has allowed for an understanding of the FFF process which has been presented in its simplest form allowing FFF users of all levels to incorporate the empirical model into their work whilst still allowing for the complexity of the process. Initial literature research showed that Polylactic Acid (PLA) is now in common use within the field of FFF and therefore was selected as the main working material for this project. The FFF technique, which combines extrusion and Computer Aided Manufacturing (CAM) techniques, has a relatively recent history with little understood about the fundamental mathematics governing the process. This project aims to rectify the apparent gap in understanding and create a basis upon which to build research for understanding complex FFF techniques and/or processes involving extruding polymer onto surfaces.